- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If it still has the original V8 engine installed you will need to locate the power steering reservoir which you should find on the drivers side front of the engine. The top on the PS reservoir will be marked to identify it as the power steering and the top also serves as a dip stick to ensure you have the correct level of fluid. When adding fluid do not overfill or you will have issues.
Many of these vehicles have had all kinds of different engines installed so if you have one of those then the PS reservoir could be anywhere at or near the front of the engine. There should be a marking on the cap to identify it though.
If you are unsure then don't do anything. Take the vehicle to a mechanic and have him locate the PS reservoir for you because you will just cause problems if you tip the PS fluid in the wrong filler.
If you can't find a power steering fluid reservoir under the hood in the engine compartment your G6 could have Electronic Power Steering . If you look up under the dash below the steering column you will see a electric motor mounted to the steering column !
The power steering system reduces the amount of effort needed to steer the vehicle. The system uses the powertrain control module (PCM), body control module (BCM), power steering control module (PSCM), discrete battery voltage supply circuit, steering shaft torque sensor, steering wheel position sensor, power steering motor, driver information center (DIC), and the serial data circuit to perform the system functions. The PSCM and the power steering motor are serviced as an assembly and are serviced separately from the steering column assembly. The steering shaft torque sensor and the steering wheel position sensor are not serviced separately from each other or from the steering column assembly. The steering column assembly does not include the power steering motor and module assembly.
It basically depends up on ,what is your car model and year.But the fluid is located in reservoir.
The power steering fluid reservoir is located next to the coolant overflow tank and the windshield washer fluid reservoir. The location of reservoir can be different or some car model ans year. Thanks.Helpmech.
The power steering fluid reservoir is located on the passenger side front of the engine, it is roughly square and black plastic with a twist off cap, check level hot and add so fluid is within two lines on the plastic dip stick which is part of the cap of the reservoir.
Locating the Power Steering reservoir and adding PS fluid. 1999 Pontiac GP
The reservoir is clearly visible in the engine bay on the 3.1 litre engine cars.
For the 3.8 Ltr engine cars,
use a flashlight to look down past the alternator for a black cap with a
steering wheel printed on it to indicate the power steering fluid reservoir. ( passenger side of the vehicle).
Remove the cap of the power steering reservoir, clean the
dipstick, re-insert and remove again to check the fluid level. If the
level is at or below the low level mark, add fluid slowly, taking care not
to fill above the MAXIMUM mark. It's best to add small amounts and re-check the level as you go to ensure you do not overfill the reservoir above the MAX level.
ONLY use the power steering fluid recommended for that vehicle by GM.
YOU HAVE A RUPTURE PRESSURE LINE IF YOU HAVE NO POWER STEERING FLUID IN THE POWER STEERING RESERVOIR.LOCATE LEAK THEN BLEED POWER STEERING SYSTEM BY ADDING POWER STEERING TO RESERVOIR.DONT OVER FILL BY FULL COLD MARK ON POWER STEERING DIP STICK.ADD FLUID TO RESERVOIR WAIT A 2 MINUTES.CHECK FLUID LEVEL AGAIN.WHEN POWER STEERING FLUID LEVEL STOP DROPPING.START ENGINE LET IT RUN FOR 10 SECONDS.THEN TURN OFF ENGINE CHECK POWER STEERING FLUID ADD FLUID IF FLUID LEVEL DROPS. WHEN FLUID LEVEL STOP DROPPING.SAFELY RAISE SUPPORT VECHICLE FRONT WHEELS.START ENGINE.NOW TURN STEERING WHEEL GENTLY FROM STOP TO STOP MEANING LEFT TO RIGHT DONT HOLD IN POSITION.LET THE STOP TO STOP BE QUICK.CHECK POWER STEERING FLUID AFTER YOU HAVE TURN STEERING WHEEL ABOUT 7 STOP TO STOP.WHEN FLUID LEVEL STOP DROPPING YOU AT HOT MARK ON DIP STICK BLEEDING PROCESS COMPLETE.TURN OFF ENGINE LOWER VECHICLE BACK TO GROUND WAIT ABOUT 5 MINUTES CHECK YOUR FLUID LEVEL.IF FLUID LOOKS LIKE A TAN COLOR.YOUR POWER STEERING SYSTEM FULL OF AIR.TURN OFF VECHICLE LET VECHICLE SET A LONG WHILE TO AIR BUBBLES SETTLE DOWN LOOK FOR LEAKS AROUND POWER STEERING PUMP FRONT SEAL AND CHECK FOR LEAKS AROUND POWER STEERING LINES.
Make sure that your vehicle is parked on a level surface and the engine is cool before you check fluid levels. Power steering fluid and other fluids read at different levels when warm instead of cool. Locate the power steering fluid reservoir. It is located under the hood of your Toyota Corolla on the passenger side next to the engine. The reservoir is connected to the power steering pump. Remove the cap and use the dipstick to check the fluid level. For the most accurate reading, clean off the dipstick with a rag first, then re-insert and remove for the fresh reading. Add automatic transmission fluid or power steering fluid approved for use in Toyota vehicles if the fluid is below the low level mark. Add fluid gradually to keep for over filling the reservoir. this will help.thanks.