Question about 2007 Dodge Caliber SXT Sport Hatchback

2 Answers

Need instuctions to change tail/break lights on 07 dodge caliber

I need to replace tail or break lights on my 2007 dodge caliber and don't know how and what part numbers are. can you help me?

Posted by on

  • 4 more comments 
  • Anonymous Dec 10, 2008

    cant get the push pins out

  • Anonymous Mar 10, 2009

    need help getting the tail lights out have no clue

  • Anonymous Mar 10, 2009

    I'm trying to change the rear brake light bulb in my 2007 Dodge Caliber and cannot get the push pins out. Help!!!

  • Anonymous May 07, 2009

    I can not get the pins out neither....what to do?

  • Anonymous Mar 22, 2014

    Changed break caliber on 1994 mazda b4000 breaks won't bleed

  • Anonymous Mar 22, 2014

    Changed break caliber on 1994 mazda b4000 breaks won't bleed

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Popohead, if people thought it was easy, they wouldn't be here asking. Your reply is useless.

To remove the pins, look a them closely. Notice that there's two little notches cut into the cup that holds the pin. Use a flathead on each side to leveredge them out a little. If that doesn't work at all, you can use a pair of pliers to firmly grip the head of the pin and pull straight out. Quick firm pull.

Once the first pin comes out, the second pin should easily come out. At that point, firmly grip your taillight housing, and pull straight back: Don't try to wiggle it out, and don't try to lift it to one side or the other like a trunk or door. Just pull it firmly straight back like you would a dresser drawer.

Once it's out, the little wiring harnesses come out of the taillight housing with about a 1/4 turn, and the bulbs just slide straight out of those.

Good luck!

Posted on Nov 01, 2009

  • 3 more comments 
  • RLFISH45 Sep 02, 2010

    Just replaced the left rear turn signal lamp on my 2010 Caliber following Khabok's instructions. Thanks to his instructions the job was easy and took about 5 minutes, including the time it took to open the right side as well and swap bulbs.
    Looking at the left bulb it didn't appear burned out so I swapped right for left to be sure.

    Way to GO, Khabok!!

  • girlfromh942 May 23, 2011

    so it took me and my dad half an hour trying to figure it out... but i finally looked online and after i read Khaboks post it took me like 4 minutes :) thank you <3

  • kc_frey
    kc_frey Sep 05, 2012

    Khabok you are the best. I just changed my 2008 tail light by myself and I'm a 50 year old lady.

  • victor dasilva
    victor dasilva Dec 01, 2013

    i need to no .my airbay ligth stays on ,sometimes the ligths blink and radio no work

  • victor dasilva
    victor dasilva Dec 01, 2013

    somebody hlep me tis a dodge caliber

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

The pins pull out the insert that holds the pins in pulls out also then carefully pull the lens out to get at the bulb it's actually pretty easy good luck and happy motoring.

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

07 dodge caliber throttle control


Usually replacing the TPS - throttle position sensor will get rid of this issue.

Mar 31, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

07 Dodge Caliber, ETC light


Try replacing the TPS first, then if your light doesn't go off, take it to the dealer.

Mar 31, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

I have a 07 Dodge Caliber, the ETC light issue


Take it to autozone or checker auto, orielly, precision etc. They can scan it for error codes for free. Then you can get a better idea of what is wrong.

Mar 31, 2014 | 2007 Dodge Caliber SRT4 Hatchback

1 Answer

On my 07 dodge caliber a lightening bolt appeared between 2 lines and the check engine light came on but everything ran fine. Please advise. Thank you


Have a repair shop check for codes every time
any light comes on your dash

Then you know if any systems have a fault & if you
should continue to use it prior to repairs

Nov 15, 2012 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

CHILL ZONE IN DODGE CALIBER NOT WORKING


There is a vent on the roof of the chill zone that allows a portion of the a/c to circulate in that compartment, keeping it cool....as long as the a/c is on...and the vent is open :-)

It's okay, I've had my 07 caliber since 07 and just now noticed that myself....hey is your dome light a flashlight?

Jun 08, 2012 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

I need to know the wiring diagram for 07 dodge caliber thanks


i doubt if you will get one ,these newer vehicles use encrypted software and modules so they do not use wires as such ,only 5 cables -two bus lines a perm 12v feed a earth and a 12v ignition switched feed .sorry--- again dealer only

Mar 08, 2010 | 2007 Dodge Caliber SXT Sport Hatchback

2 Answers

Need instructions to change tail/break lights on 08 dodge caliber


I dont know the exact method on this car but on most cars if you open the boot/ trunk it has little compartments near the lights on the inside of the car, if you pop those open you gan get to the bulbs and probly un screw the light unit it self. sorry if its no help.

Feb 16, 2010 | 2007 Dodge Caliber SXT Sport Hatchback

2 Answers

How do you replace break lights in 2007 Dodge Caliber?


Look inside the rear hatch area near the very rear of the vehicle. You should find a removable panel near the brake light housing. After you carefully remove the panel, look for some plastic wingnuts that hold the light housing in, and remove them, you should not need any tools to do this. After the nuts are removed you should be able to gently remove the tail light assembly from the rear of the car. Becareful not to damage the wiring. Now look at the back side of the tail lamp assembly and look for a locking tab on the light socket. Depress the locking tab and twist the light socket about a quarter turn, then pull the light socket away from the light housing. Pull the bulb out and replace it. Then reassemble and your done.

Aug 27, 2009 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

Needing to locate the airbag control module '07 caliber


it is located behind the floor shifter in center console..under small piece of carpet

Jun 16, 2009 | 2007 Dodge Caliber SXT Sport Hatchback

Not finding what you are looking for?
2007 Dodge Caliber SXT Sport Hatchback Logo

7,986 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...