Question about 2000 Oldsmobile Intrigue
I have a 2002 Oldsmobile intrigue GL. I noticed the traction control isnt working. When i first start the car the traction control light doesnt light, the switch to turn the traction control does turn on a "track off" light. The ABS system (which i belive is linked to trac) does work fine. is there a fuse somewhere for this? i didnt see any fuses dedicated to traction control in the owners manual
GM DELCO THEFTLOCK RADIO UNLOCK CODE:
1. Press and hold presets 2 and 3 for about 5 to 10 seconds until you
get 3 digits on your display. This is the first 3 of 6 digits you will
need, so write 'em down.
2. After doing step one and writing down the code, immediately press
AM/FM button to get the last 3 of the 6 numbers you'll need, and write
'em down. (if you wait too long between steps 1 and 2 and the LOC code
displays again, just start over).
3. Call this number, it's a prerecorded message, so don't worry about
having to talk to anyone...1-800-537-5140. The voice will ask if
calling for Chevy, Pontiac, Cadillac, etc... When you here him tell
to press "2" for Pontiac, press 206010 and hit the # key. He'll ask
for the 6 digit code that you've written down. Enter that and press
* key. He will then give you a code, and the option to get additional
digit codes, but one should be sufficient.
4. Follow the normal procedure in your owners manual for unlocking the
radio with your new code...press the hour set button on your radio
you get the first two numbers of the code, then press the minute set
button until you've entered the last two numbers. Immediately press
AM/FM button once the correct code is entered and the code SEC or
"secured" will be displayed on the display screen. Now, just turn the
radio on, and your ready to roll.
There is an additional step you can take to remove all codes from the
radio and start from scratch by entering your own personalized 4 digit
code so that it won't get you in a pickle again! Just repeat step 4
you should get a display screen that reads ---. This means the code is
out, and you can now program your own code. Of course, once you
the 4 digit code from the GM recorded message, just keep it in a safe
place, because you can use that same code again and again should you
have any more problems with it in the future. Good luck, and yes, it
Posted on Nov 13, 2008
SOURCE: 2000 oldsmobile Intrigue V6
This could be a # of problems but try these: Remove gas cap and carefully inspect it and the fuel filler neck for small cracks and/or distortion/dirt. Under the hood there is a small green cap which is the test port for the evap system, remove it and check the schrader valve to be sure its tight ( left hand threads!!!). Check all hoses attached to this for cracks/breaks.Other than this a diagnostic will have to be ran with a smoke machine to pin point leaks or valve/switch/solenoid/canister failure.
Posted on Jan 14, 2009
SOURCE: 2000 oldsmobile alero gl 2.4
The window regulator is what causes the plastic clip to break. I had the same problem. I was able to find a new clip at advanve auto parts, and had to purchase a regulator which includes the motor from ebay. There were many diffrent options out there. Total cost was about $60.
Posted on Feb 17, 2009
SOURCE: i have an 1998 Oldsmobile
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then pull back the weather seal and you will be able to put it back on the track. You will most likely need to buy some clips to secure it back on
Posted on Oct 21, 2009
You need to have the abs system scanned for codes. You likely have a bad wheel speed sensor on one of wheels.
Posted on Apr 21, 2010
. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wIre CONNECTOR plug to the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery.
Posted on Jun 05, 2010
Tips for a great answer:
Oct 13, 2015 | 1998 Oldsmobile Intrigue
Jun 19, 2015 | 2001 Oldsmobile Intrigue
Jan 13, 2013 | Cars & Trucks
Jun 18, 2012 | 1998 Oldsmobile Intrigue
Apr 08, 2011 | Oldsmobile Intrigue Cars & Trucks
Apr 21, 2010 | 2000 Oldsmobile Intrigue
Dec 14, 2009 | 2002 Oldsmobile Intrigue
Mar 31, 2009 | 1999 Oldsmobile Alero
688 people viewed this question
Usually answered in minutes!