Question about 2004 Ford Explorer Sport Trac

2 Answers

High beams wont turn on.

Low beams work fine go to turn on high beams i have no headlights at all. when i have fog lamps and low beam on and hit high beams fog light go out. please any help would be appreciated. thank u.

Posted by on

  • 6 more comments 
  • Anonymous Mar 12, 2014

    low beams work but high beams wont work

  • Anonymous Mar 13, 2014

    Front headlights come on but the high beams

  • Anonymous Mar 15, 2014

    low beam lights work, high beam lights wont turn on

  • Anonymous Mar 15, 2014

    while changing a headlight bulb I lost my low beam and driving lights but the high beams still work. whats wrong.

  • Anonymous Mar 18, 2014

    My company bought a new 13 F550 and at 3,000 miles the high beams only came on if you held the multifunction switch, then when the high beams did come on they wouldn't go back to low beams, until like a half hour later after hitting a lot of bumps.

  • Anonymous Mar 24, 2014

    pump works fine in low but this happens in high

  • Anonymous Mar 27, 2014

    Low beams working but the high beams aren't working. The lights turn off when the knob is on the high beam position.

  • Anonymous Mar 30, 2014

    drivers side low beam went out the other day. replaced both headlight bulbs (as recommended) and the one still does not work. high beams work on both. fog lamps work for both.

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 193 Answers

First place to start is with headlight switch. I did have a case many years ago when both high beams were blown out at once, but this is rare. When you have the headlight switch out, jump power from te low beams to the high beam contacts. If high beams come on, replace switch.
Bill

Posted on Nov 19, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 93 Answers

Park up to a wall with the lights on and move the dimmer switch slowly on and off up and down and see if you get a flicker of lights...probably a bad switch

Posted on Nov 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

2 Answers

No headlights or fog lights


I suspect it is the headlight switch

Mar 18, 2014 | 2004 Pontiac Grand Am

1 Answer

High beam indicator comes on with fog lights


Could your Mazda have daytime running lights? If you checked all fuses, did that include the three in the joint box?

There is an auto light-off control module that is central to all functions you describe. It is assumed that you would only turn on the fog lights with headlights on and set for high beam. If you set the headlight switch to LOW, the module closes the headlight relay to turn on the low beams. If you then turn the headlight switch to HIGH, the module turns on the high beams and allows you to turn on the FOG LIGHT switch, closing the fog light relay and turning on the fog lights. Since this sequence is not working, I suggest checking both high beam lamps as both could be burned out. Other possibilities are a defective headlight switch or the module

Oct 01, 2012 | 2005 Mazda 6

2 Answers

2005 Ford Focus ZX3 SES, the blue high beam indicator in the dash comes on with low beams, and goes off with high beams. The indicator is on at the wrong time! I have tried the following: The turn signal...


It sounds like you are confused about how your headlamp system is supposed to work. The DRL does not run on the High beam circuit, it runs on the low beam circuit. The fog lamps are supposed operate with the park lamps and also with the low beams, not the high beams. From your description, I would say that your system is operating as designed and you are having trouble telling High from Low. (Don't feel bad, that is why high beam indicators were invented in the first place.)

May 08, 2011 | 2005 Ford Focus

1 Answer

My 2000 Blazer low beam headlights won't come on .High beams, fog,running, turn signals all work fine.


Try changing the headlights....some headlight high beams will work even when the low beams dont

Aug 17, 2010 | 1995 Chevrolet Blazer

1 Answer

Passenger headlights only do not operate.


check the bulbs first and also the fuses theres a fuse for each side and for low and high beams, start there, good luck.

Feb 19, 2010 | 2002 Mitsubishi Eclipse Spyder

1 Answer

Low beam headlight are not working. high beams and fogs lamps work fine. is there a fuse for a controller?both low beams stopped working at the same time so i don't think it the fuse for the headlamps.


The problem could be the headlamp switch.
You are right about the fuses.There is one for the LH high/low and one for the RH high/low.
Have you tried turning on the lamps manually with the switch?

Nov 10, 2009 | 2006 Pontiac Torrent

1 Answer

Headlight trouble on sunfire 2003 with 2.2ecotech


sounds like either a wiring loom is shorting across somewhere ??where ----best of british to finding it

Aug 05, 2009 | 2003 Pontiac Sunfire

1 Answer

Low beam headlights not working on 2004 Pontiac Montana extended


You headlight lamp have a diffuser mechanism which allows it to flip between the hight beam and low beam feature of the bulb. In fact, you high beam will function even if the low beam is not working.

I would recommend the purchase of the new headlight lamp. It would cost you you any where from $15.00 per unit to get a replacement lamp

Dec 26, 2008 | 2004 Pontiac Montana

Not finding what you are looking for?
Cars & Trucks Logo

1,450 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...