Question about 2000 GMC New Sierra 1500

1 Answer

Removing front wheelbearings from 2000 gmc 1500 4x2 reguler cab

Im trying remove the wheelbearing off the a arm all boalts are removed and anti lock brake line what nexts?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 95 Answers

Its probably rusted in place...make sure all 4 bolts are out of the spindle and tap it out with a hammer

Posted on Nov 19, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Removel of front rotor

remove brake caliper and pads. remove dust shield from center of wheelbearing. gives you access to the nut that holds rotor on.word of advice,check wheel bearings and replace rotor.not that expensive.

Apr 21, 2013 | 1995 Ford F250

1 Answer

Front wheelbearing replacement

Wheel, Brake rotor and caliper need to be removed. Lower ball joint needs to be poped loose to allow CV half shaft to be removed. There should be 3 bolts on the inside of spindle remove those.There should also be a speed sensor loosen fastener to it. Cheap replacement parts may not come with a new sensor. NAPA does.

Jul 02, 2012 | 2001 Buick Regal

1 Answer

Dodge ram wheelbearing number

front inner, cone pt# 52007659
front inner, cup pt# 4746921
front outter, cone pt# 52007899
front outter, cup pt# 4746922

those are straight off mitchell ondemand

front seal is # 52007658

Nov 30, 2010 | 1997 Dodge Ram 1500 Club Cab

2 Answers

Vibration and allignment

have the front end checked for worn parts, something is worn out, hard to say without hands on look at the parts, any tire shop like Big O will do an inspection for free.

Apr 29, 2010 | 2001 GMC Sierra 2500HD

2 Answers

Having trouble changing brake rotors on our 1999 Geo Metro


Apr 12, 2010 | 1999 Chevrolet Metro

1 Answer

Having a hard time removing front wheelbearing on 2000 daewoo lan

rent a 3 prong puller from a parts house. they'll come in a kit, so they'll be different sizes. that should take care of it. you'll get your money back when you return the tools as good as new. good luck.

Aug 29, 2009 | Daewoo Lanos Cars & Trucks

2 Answers

2000 GMC Safari anti-lock brakes

There was actually a recall for this. Go to your local GMdealer and have them check your VIN for a recall. If not under recall get out of there its easy to repair yourself don't let'em fool you.Remove the front pads caliper and rotors. Locate the abs sensor mounted to the wheelbearing assembly by a small socket head cap screw (Allen wrench). Removethe bolt and softly gently/wiggle the abs sensor around until it pops upout of the hole. some will break, which is why it wouldbe nice if the recall applies to your vehicle that way if they break gm replaces. Once you get both sides removed, clean themounting surface of all rust or build up with w-d 40 and small steel toothbrush then wipe off excess with clean rag and mild soap and warm water, dry completely make sure no spray residue exist on parts, Next apply a thin layer of lubricant grease to preventfuture rusting and reassemble.The rust build up under the sensor is causing the angle to change resultingin inaccurate wheel speed readings in the abs module your abs module will interprets this asa wheel is either slipping or skidding and applies your abs. This should make you happy with no more irritations. Please rate me. If you need further assistance you can always ask me. Good luck with this.

Apr 25, 2009 | 2000 GMC Safari

2 Answers

Bad front wheelbearing 2006 gmc sierra 1/2 ton pickup

Not too bad. Just break down the Hub and pull it out. You might need a big socket. Go get a chilton's manual, it will help you if you don't understand it.

Mar 26, 2009 | 2006 GMC Sierra

2 Answers

Wheelbearing replacement

Welcome to FixYa
the front wheel bearing is a hub unit.
need to remove the tire,brake caliper, rotor, the 34mm nut in the axle, then there is 3 bolts that hold the hub to the spindle, those come off then the hub comes out,reverse to install.

Jan 12, 2009 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides