Cars & Trucks Logo
Posted on Nov 19, 2008

1995 DODGE RAM B1500 NO START

I have 1995 Dodge Ram Van B1500, 5.2L v8. Recenlty, the car would not start. It would crank but would not turn over. I check the fuel and it was coming out, so I replaced the fuel pump assembly. A day later, it happend again, it would crank , but would not turn over. This time there were no spark and fuel injectors are not working either. I went through the basic check and messure voltage for Crankshaft & Camshaft sensor, they seems to be working. I though it might be the ASD Relay, so I replced it and but it was the same. Does anyone know how or what way to measure the signal that Crank sensor is receiving and sending it to the PCM?

Thanks
Mike

  • CAMJIKUS Nov 25, 2008

    Thanks for the info. I've retested the Crank Sensor by checking ohm reading for terminal "B & C" and it did not give me any ohms. Replaced the Crank Sensor and it solved the problem.



    Thanks

  • myvan Dec 21, 2008

    where is the crank sensor?
    we tested it a while ago and it said crank shaft sensor or something like that.
    my van does not turn over.
    thank you



×

2 Answers

Shawn Wright

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on Nov 27, 2022
Shawn Wright
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Nov 27, 2022
Answers
1
Questions
0
Helped
1001
Points
4

I am having the same exact issue with my 1995 dodge ram 1500 5.9L i have no spark at coil or no fuel injector pulse.... Im lost on what else to do myself i have changed the computer checked all the fuses and relays and wires... Someone please help its my only vehicle and i do not have any other way to work.... I have also changed the crank sensor and cam sensor 2 times and still nothing.... Someone please any info will be greatly thankful.... if it helps any a week before it did thiss it took me 30 mins to get it to crank one day then wen it started this it popped back one time and never ran again it also has a new timing chain also i checked 5 times to make sure its dead in time....

Anonymous

Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Problem Solver:

An expert who has answered 5 questions.

  • Contributor 16 Answers
  • Posted on Nov 22, 2008
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Problem Solver:

An expert who has answered 5 questions.

Joined: Nov 22, 2008
Answers
16
Questions
0
Helped
6841
Points
22

You need to use a LED type test light for the injectors or a Bosch style Noid light for the injector. To test the cam/crank sensor signal you either need a scanner to read them or a lab scope to show you a signal. The pickup plate in the dist handles the injector timing, the crank sensor provides a RPM signal. They both feed the computer information for ignition timing. Good fuel pressure, injector activity(Noid), and good spark out of the coil. The coil is what I replace the most of.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
1helpful
1answer

I have no injector impluse

no injector pulse - DodgeForum.com

dodgeforum.com/forum/2nd-gen-ram.../269362-no-injector-pulse.html
Nov 21, 2010 - no injector pulse 2nd Gen Ram Tech. ... but was running and driving fine before. as far as i can tell i have no injector pulse. tested with a noid ... No spark AND no fuel injector pulse ONLY when van is cold ...
Nov 18, 2013
2000 ram 1500 Has spark but no injector pulse wont start ...
Jun 25, 2013
v10 RAM no start....frustrated
Sep 19, 2011
help - no spark, no injector pulse, no run
Oct 30, 2009
More results from dodgeforum.com

No injector pulse 02 Ram 1500 - DodgeTalk : Dodge Car Forums ...

www.dodgetalk.com > ... > 3G Dodge RAM - General Talk
May 30, 2012 - No injector pulse 02 Ram 1500 3G Dodge RAM - General Talk
0helpful
1answer

I have a 1998 dodge van B1500 with a 5.2L . Problem is that the van just shuts down while driving. I have replaced the fuel pump, fuel filter, fuel relay, TPS fuel pressure regulator... I out of ideas can...

My Ram recentlystarted running horribly to the point of the engine not even reaching 2000rpms. I was fearing the worst but it turned out to be the catalytic converter stopped up. I fixed it and it runs good as new.
1helpful
1answer

97 dodge ram van 5.9 litter cranks over and over but no start no spark

First thing to check is the ASD relay and voltage at the coil.
2helpful
1answer

2001 dodge 3500 van cam position sensor location

Crank sensor is in the bell housing of the transmission. Cam sensor is in the distributor.
0helpful
1answer

460 1995dodge ram cranks won't start wiggle wires sometimes works

A friend of mine has a Dakota about that same year, he had to replace the computer. His was acting the same way he bought a reconditioned one from Autozone, I think for about $100.
4helpful
1answer

Sprak plug Wires Need To Be Installed Correctly

You have several RAM sub-models in here:
Normal 0 21 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabla normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} B1500 RAM Van
B2500 RAM Van
B3500 RAM Van
RAM 1500 1/2 ton 2WD
RAM 1500 1/2 ton 4WD
RAM 2500 3/4 ton 2WD
RAM 2500 3/4 ton 4WD
RAM 3500 1 ton 2WD
RAM 3500 1 ton 4WD

Chrysler Full-Size Trucks 1989-1996 Repair Guide
To avoid confusion, remove and tag the wires one at a time for replacement.


f160dd3.jpg


Fig. 1: 2.5L 4-cylinder Engine. Engine Firing Order: 1-3-4-2. Distributor Rotation: Clockwise


a1a8242.jpg

Fig. 2: 3.9L V6 Engine. Engine Firing Order: 1-6-5-4-3-2. Distributor Rotation: Clockwise


dc6748e.jpg

Fig. 3: 5.2L and 5.9L V8 Engines. Engine Firing Order: 1-8-4-3-6-5-7-2. Distributor Rotation: Clockwise


832c92e.jpg

Fig. 4: 8.0L V10 Engine. Engine Firing Order: 1-10-9-4-3-6-5-8-7-2. Distributorless Ignition


Hope helped with this (remember rated this help) Good luck.
7helpful
1answer

Van stops running

You need to look at your fuel pump it does not pump to specification when it gets hot. You might just have to replace it.

Good luck
Not finding what you are looking for?

1,011 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...