Question about 1994 Ford Crown Victoria

1 Answer

Oil Leak I have an oil leak on a 94 crown vic, somewhere on the driver's side above the oil filter area.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 235 Answers

Sounds like the oil filter housing gasket is leaking. clean the area up real good with some brake clean and then run vehicle for 15 to 30 min and see if u can see whare its coming from. it may also be coming from valve cover gasket.

Posted on Jan 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Oil leak in driver side rear wheel well for 2005 crown vic. drips down over top of tire and puddles under it.


Hi Don:
Have you checked to see if it's brake fluid?
Is it possible that the slave cylinder is leaking and the fluid is coming ot from the brakes? I can't think of any oil source in that area.

Jul 21, 2011 | 2005 Ford Crown Victoria

1 Answer

Looks like the water leak in my 89 ford crown vic is coming from above the oil pan. no water in oil far as i can tell. i add a qt of antifreeze everyday. i live in north texas. the heater hasnt worked...


until you can see the leak its still guess work --either mechanic didnt do repair correctly or you have a crack in block --use a mirror and light to look in area for origin of leak

Apr 20, 2017 | 1989 Ford Crown Victoria

1 Answer

1984 crown vic. where is the fuel filter located?


most of the time fuel filters are located on the drivers side, under the vehicle, on the inside of the frame. in the area of the door. but some have been further back

Jan 28, 2011 | 1984 Ford Crown Victoria

2 Answers

I have a 94 crown vic that blows blueish white smoke sumtimes on acceleration but then it goes away, it doesnt do it on start up and it runs fine otherwise


If there is a blue tint you are burning oil. You may have worn rings, or you may have one ring that is stuck and letting oil by. There may also be hardened valve stem seals. As old as it is try switching to full synthetic oil after doing an engine clean. It will not burn.

Hope this helps

Apr 09, 2010 | 1994 Ford Crown Victoria

1 Answer

Oil leak 94 dodge caravan 3.0L


Could it be the rear main seal? Some times oil can be "blown" around in bell housing from fly wheel. If you can pry the inspection plate with a little regular screw driver and oil starts to come out its a good chance its the rear main

Aug 06, 2009 | 1994 Dodge Caravan

1 Answer

94 crown vic how do i find out if car has keyless entry


Easy. Does your Vic have a five number keypad above the driver's side exterior door handle? If so the you got key-less. If not, you do not.

Jun 13, 2009 | 1994 Ford Crown Victoria

1 Answer

Crown vic oil change


Some of them have an oil plug at the front of the pan, as well as the regular one. You have to drain them both. The front one only holds a quart or less.

May 21, 2009 | 1990 Ford LTD Crown Victoria

1 Answer

Locate fuel filter on 91 crown vic


The fuel filter is located under the vehicle on the inner side of the left (driver side) frame rail.

Should look like the image below:
a31eb6c.jpg

Apr 13, 2009 | 2008 Ford Crown Victoria

1 Answer

2002 crown vic


you need to jack that side of the engine up. take the right side motor mount bolt loose then jack the engine up from underneath. be sure to use a block of wood or somthing so you dont bust the oil pan

Jul 22, 2008 | 2002 Ford Crown Victoria

Not finding what you are looking for?
1994 Ford Crown Victoria Logo

Related Topics:

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5626 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...