Question about 1995 Chevrolet Beretta

1 Answer

Heater core broken

I have a 95 beretta how much of the dash do i need to take out

Posted by on

  • angelbunny33 Nov 19, 2008

    Thank you so much for the info. Cindy

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 150 Answers

All of it don't try this at home unless you are experienced.

  1. Disable the Supplemental Inflatable Restraint (SIR) system, refer to Disabling the Supplemental Inflatable Restraint (SIR) System. See: Body and Frame\Interior Moulding / Trim\Air Bag(s) Arming and Disarming\Service and Repair
  2. Negative battery cable.
  3. Drain cooling system.
  4. Raise vehicle.
  5. Drain tube from heater case.
  6. Heater hoses from heater core.
  7. Lower vehicle.
  8. Right and left sound insulators.
  9. Steering column opening filler.
  10. Floor air outlet duct.
  11. Heater core cover.
  12. Heater core mounting clamps and remove heater core.

Posted on Nov 19, 2008

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater is not getting hot whats the problem


thermostat could be bad, heater core could be bad, blower motor could be bad. See if the blower motor turns on (passenger side under the dash). if it does then i would replace the thermostat. depending on how old the vehicle is you may want to have it flushed, something could be backed up. the last resort is the heater core because that is really involved and timely. it involves (in most cars) taking the entire dashboard out. for a feel, years ago it took me around 8 hrs just to get the the heater core in my chevy beretta. good luck

Dec 03, 2012 | Cars & Trucks

1 Answer

Trying to put on a heater core in dash of 95 ford van and having hard time disonnecting the heater hose


they can stick good. if ur going to scrap the old one then just break them off and take it out. then u can cut the hose back just enough to get them out. make sure u dont cut urself though. the broken aluminum will be very sharp.

Nov 17, 2010 | Ford E-150 Cars & Trucks

1 Answer

How do I cange the heater core in my 1995 Chevy Berretta


Start by removing the panel under the dash on the passenger side. You will need a regular phillips screwdriver and a snubby 2-3" phillips later. Also get a 1/4" socket set. First thing, go under the car and remove the heater hoses from the firewall and twist out the drain spiggot. Then go back inside the car. The heater core sits under the radio. Under the core is a tray used to catch the leaking antifreeze and drain it out the firewall. You need to remove this tray. It has 6-8 screws holding it. Once the screws are out it is tricky removing it with the center console in, but it can be done-twist and bend. Then remove the screws holding the core in place and pull out the heater core. One note on the replacement-got mine from Oreilly's for $20-the two lines coming out of the heater core swivel to line up with the holes through the firewall. If you don't swivel them it will never seem to fit. Then reverse the above order, fill up the fluid, bleed the air off and away you go. Took me about 3 hours total in a parking lot. Ruined a shirt, but got it done. You will also cuss being upside down under the dash. It's a small place for a 240 lb. guy :) This was for a 1993 Beretta. Expect some bloody knuckles and a few mental breakdowns.

Good luck, and rated the help!!!
REMOVAL & INSTALLATION CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

For heater core removal on these vehicles, please refer to the procedure for vehicles with A/C.
1994-96 VEHICLES
See Figures 1, 2 and 3
  1. Properly disable the SIR system, as outlined earlier in this section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system into a suitable container.
  4. Raise and safely support the vehicle.
  5. Disconnect the drain tube from the heater case.
  6. Detach the heater hoses from the heater core.
  7. Carefully lower the vehicle.
  8. Remove the right and left sound insulators.
  9. Remove the steering column opening filler.
  10. Remove the floor air outlet duct.
  11. Remove the heater core cover.
  12. Unfasten the heater core mounting clamps, then remove the heater core from the vehicle.
bda4cf8.gif
Fig. 1: The heater core is located in the passenger's side footwell, below the glove compartment

d3686c3.gif
Fig. 2: Exploded view of the heater core and related components (1 of 2) - 1994-96 vehicles

45d1f7c.gif
Fig. 3: Component list for the heater core and related system components (2 of 2) - 1994-96 vehicles

To install:
  1. Position the heater core in the vehicle and secure with the mounting straps.
  2. Install the heater core cover.
  3. Install the floor air outlet duct.
  4. Install the right and left sound insulators.
  5. Install the steering column opening filler.
  6. Raise and safely support the vehicle.
  7. Connect the heater hoses to the heater core.
  8. Attach the drain tube to the heater case.
  9. Carefully lower the vehicle.
  10. Connect the negative battery cable.
  11. Enable the SIR system, as outlined earlier in this section.
  12. Connect the negative battery cable, then start the engine and check for coolant leaks. Check the coolant level, and add if necessary.
WWW.AUTOZONE.COM

Aug 11, 2009 | 1995 Chevrolet Beretta

1 Answer

Need to remove dash to get to heater core


Some upper panel bolts are located behind plastic tabs, the rest cab be pried off.

Jul 02, 2009 | 1990 Chevrolet Beretta

1 Answer

Lower dash removal


The lower dash is pried off. Then there are screws for the heater core cover

Jul 02, 2009 | 1990 Chevrolet Beretta

2 Answers

95 Chevy Beretta 3.1 engine will not warm up


termperature sensor needs to be replaced

Feb 11, 2009 | 1991 Chevrolet Beretta

1 Answer

I need to know where the hoses go from the heater core?


Have had the same problem with a Corsica.The reason they bypassed the heater core is that it had a hole in it.Reccomend filling with water prior to hooking up hoses.

Feb 04, 2009 | 1991 Chevrolet Beretta

1 Answer

How to change heater core in it under the dash or under the hood on 95


it is under the dash...you will need to remove the dash to access the hvac box and the door for the heater core

Sep 09, 2008 | 2004 Dodge Stratus

Not finding what you are looking for?
1995 Chevrolet Beretta Logo

Related Topics:

491 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...