Rx300 2003 model, black key with remote working fine for last 500miles, today morning wont start
SOURCE: 2005 ford taurus. Remote entry wont work theft light keeps blinking when key is engaged
HI, I'm reading your problem,
Let me explain something about your car.
2005 Ford Taurus, The key on that car has Chip inside of the key and receiver on the ignition switch,
Check if the key you are trying to use is Black and has a plastic head.
If not you need a key with that characteristics.
But if you have the right key, Remenber if you had drop on the floor, or hit with something,
Because some times they come damaged, with insignificat thins.
Remenber if you left the key close to a magnets like speakers.
If nothing aply at your case, you need to call a place Aloha Smith, they have the computer to program or reprogarm your key. IF not you can't start your car.
OK.. I hope this information work for you.
Thank's for submit yous question on fixya.com
SOURCE: The Lexus car remote key control model ES300
try this:
1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.
2. Insert key into the ignition (DO NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.
4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes.
SOURCE: replace side marker light on lexus rx300
Remove 3 - 4 screws on fender cover close to side marker light. Pull fender cover out a bit for you to use your other hand to reach side marker light. By twisting on one direction and here you go the light out. Replace new bulb and replace everything on reverse order.
SOURCE: security light blinks on dash , truck wont even try to start
Does your key have a chip on it? If it does its probably the problem
SOURCE: 1999 lexus rx300 check engine
Your 306 code means you have a misfire on cylender 6. That may be the cause of the po 125. Inspecdt the coil, spark plug wire, and spark plug on cylender 6. With the age of the car I would replace all 3 items. If you want know how to test all 3 I can tell you process of elimination is the way to do it. Do you know how to find cylender 6
You should see three buttons on the driver sun shade. Let's name them from left to right 1,2, and 3. Start by clearing any old codes. To clear codes press buttons 1 and 3 simultaneously until the light starts blinking. Release the buttons simultaneously. Before starting to program the car remotes you must have your gate hand held remote ready with a good charged battery. Now, to program your first gate car remote let's choose button 1. Press button 1 until it start blinking (about 20 seconds). Keeping button 1 pressed, activate your hand held remote close (about an inch) from the car button 1, until the light blinks faster than before. Release both remotes simultaneously. You are done programming your car remote button 1. For two additional gates remote controls programming repeat the procedure with button 2 and then with button 3.
5,346 views
Usually answered in minutes!
×