Question about Toyota Camry

1 Answer

My cv joints on my 1992 toyota camry broke and I need instructions on replacing them

Posted by on

  • 1 more comment 
  • Randuarte420 Dec 16, 2008

    how do I remove the inner cv joint boot on 1993 toyota camry

  • yadayada
    yadayada May 11, 2010

    Just saw the year, sorry, will look it up and let you know, but you will need to remove the axle to do it with any ease.

  • yadayada
    yadayada May 11, 2010

    What year?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Toyota Master
  • 1,779 Answers

There is a lot of labor involved in changing the cv joints. I would strongly recommend purchasing a good repair manual (Chilton or Haynes), or going on line to alldata or e-mitchell auto repair to get all the necessary info on doing this repair. The cost of this info is small considering what u will save by doing it yourself. Good luck, let me know if this helps out.

Posted on Nov 19, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace a cv joint

I can tell you how to replace the CV joint but it is by far better to just buy a re-manufactured axle. The price of the CV joint itself then the labor to remove the axle, change the joint and install it is a big pain. Changing just the CV joint is labor intensive and you could run in to problems. Don't risk it, but a rebuilt.

Mar 23, 2014 | 1994 Toyota Camry

1 Answer

Toyota camry

That usually is a worn CV joint. Go to a smooth surface like a parking lot, wind the windows down, and turn slow circles on full lock. If you hear that noise, it is probably the CV joints and not ball joint noise, since you are not going over bumps.
Also look at the CV rubber boots (2 each side) to find any splits in them. Those let grease out and dirt in, and rapidly end the life of a CV joint.

The individual joints can be replaced, but it isn't worth it. If worn out, get a complete re-manufactured front axle each side.

Jan 28, 2013 | Toyota Camry Cars & Trucks

1 Answer

My 96 camry is starting just fine. When I put it in reverse, or any gear for that matter, and step on the gas it goes no where. It just revs the engine but doesn't move a inch. I was told it could be a...

Well if it was a cv joint and you put it in gear it would be banging around if it was broke. More likely a trans problem. did you check the fluid level?

Dec 31, 2011 | 1996 Toyota Camry

1 Answer

I need to change the front right CV DRIVE SHAFT of my 2002 Toyota Camry.

Cheaper to find a complete assy at a salvage yard. To replace the axle unless you are handy with tools would recommend buy the axel and take it to a repair shop.
To check the CV joint do a visual inspection, they normally have a torn boot and dirt in the joints and causes them to fail. Also to check it drive the car it will make a bumping noise when you turn hard either direction

Nov 13, 2009 | 2002 Toyota Camry

1 Answer

1992 Toyota Corolla CV Joint

You can pick up an entire re manufactured axle assembly at your local auto parts store. In order to replace the assembly you will need to disconnect the tie rod end and the ball joint. Remove the spindle nut. Push the axle stub out of the hub. Now with a suitable container under the axle to catch spilled fluid pry the axle from the transmission housing. Install is the reverse of removal. For more detailed instructions and diagrams go to vehicle repair guides.

Oct 29, 2009 | 1992 Toyota Corolla

1 Answer

How to replace a cv joint on a 2005 toyota corolla, i cant get the cv joint back part off the transmittion. driver side cv joint broke and rear part is stuck to transmittion..

There are two types of cv joints used. One type bolts on the other you have to pop out. Do this by prying it out with a big screwdriver. A c-clip hods it in and it will pop out for you. When reinstalling be sure it seats back in.

Jul 26, 2009 | Toyota Corolla Cars & Trucks

1 Answer

I need to replace the axle on my toyota camry

The CV joint boots? Hah.. if you've never done it before get a mechanic to do it. You'll just run into more and more problems if you mess up. There's more to it then just replacing the boot. You'll also need to check the cv joints for damage and repack them with high pressure grease.

Mar 06, 2009 | 1991 Toyota Camry

1 Answer

Um cv joint

a whole lot faster to just replace the whole half shaft

Nov 09, 2008 | 1991 Toyota Camry

1 Answer


it could be someting up ur exhaust check it with a rod

Jun 25, 2008 | 1992 Toyota Camry V6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

782 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides