Question about 1985 Cadillac Fleetwood

1 Answer

Rear hubs moving in and out about quarter to half inch

Axle retainers or bearing retainers maybe

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 303 Answers

The pin is worn if it is a c lock could be the c clip or axle if its old could be all not hard to check pull the cover .

Posted on Nov 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u remove hubs on a 1992 Isuzu big horn


TO DO WHAT? not even the smallest hint on job or failure.>?
USA?
hubs, the rears have hubs to with disc brake option.rotor hubs.
I guess front hubs?.
guess 2, wheel bearing hubs, and not 4wd axle locking hub units.
doing what?
brakes, wheel bearings, axle damage. 4wd axle bearings what?
the pages are 2wd pages, and 4 wd pages, which is yours?
is this your first time DIY ever. ? or first time 4wd?
guess 3, 4wd, how am I guessing....


names
Acura SLX
Chevrolet Trooper
Isuzu Bighorn
Holden Jackaroo
Holden Monterey
Honda Horizon
HSV Jackaroo
Opel Monterey
Subaru Bighorn
Vauxhall Monterey
wow......
our usa book lists it as trooper only.
so ...

just B or B then A off? if you had b off, you'd see what?, a big nut.
that is locked to spindle shaft.
ill guess? wheel bearings are bad? (just in hub not spindle bearings bad... no matter this is first.)
so you do what. ? here are the steps.

that part"B" must be off first, see the bolts holding it, ?
B = auto locking hubs. or hub axle lockers.
26005769-b5pjo3cin0lhc1b54v4xlnuy-4-0.jpg you can see the caliber must come off, so, do so and tie them up.
  1. "Place the Transfer shift in the 2H position.
  2. Raise and support the front of the vehicle safely on jackstands. (rear tires chocked, and hand brake set hard)
  3. Remove the wheel and tire assembly.
  4. Loosen the hub to rotor retainer bolts.
  5. Remove the brake caliper mounting bolts and carefully remove the caliper (along with the brake pads) from the rotor. Do not disconnect the brake line. Secure the caliper out of the way with the flexible line still connected.
  6. Remove the hub nut using hub wrench J-29020-A or equivalent. ( special tool)
  7. Remove the hub cap assembly retainer bolts. Remove the spindle nut, washers, and other components. Remove the hub/rotor, being careful not to drop the outer wheel bearings. As the hub/rotor is pulled forward, the outer wheel bearings will often fall forward.
  8. Once the hub/rotor is removed, remove the retainer bolts securing the rotor and hub together. Inspect the hub and replace if needed."
  9. end removal. install is next... (alldata.com covers this)

Dec 13, 2015 | Isuzu Cars & Trucks

1 Answer

How to change a rear wheel bearing on a 2004 ford taurus???


How to Replace Rear Wheel Bearing/Hub Assembly on a 2nd generation Taurus

The following procedure is for a Ford Taurus (VIN S), with rear drum brakes and ABS.

1. Loosen wheel lug nuts, raise rear of vehicle, and support securely on jack stands. Block front wheels and remove rear wheels.

2. Remove brake drum (parking brake must be off).

3. Remove and clean ABS Sensor (Torx E8) with a spritzled rag.

4. Remove grease cap from hub.

5. Remove and discard hub retaining nut (36 mm). This is a compound nut, comprised of several nuts inside a metal cage. Use a 36 mm axle nut socket (e.g., OEM 25206). Many auto parts stores will lend you this socket. A 1/2-inch drive air impact wrench or breaker bar is necessary to remove the nut.

6. Remove wheel bearing/hub assembly from spindle. It easily comes off by hand.

7. Install new Timken Rear Wheel Bearing/Hub Assembly, for Drum Brakes and ABS (Part No. 512162). Tighten new axle spindle nut (Dorman 05114) 221 lb.-ft., replace grease cap, and button everything up.

Jun 22, 2012 | 2004 Ford Taurus

1 Answer

Remove rear brake drums


Light Duty Models
  1. Raise the vehicle so that the wheel to be worked on is clear of the floor and install jackstands under the vehicle.
  2. Remove the wheel. Remove the three retaining nuts and remove the brake drum. It may be necessary to back off the brake shoe adjustment in order to remove the brake drum. This is because the drum might be grooved or worn from being in service for an extended period of time.
  3. Before installing a new brake drum, be sure to remove any protective coating with brake cleaner or a suitable fast-drying degreaser.
  4. Install the brake drum in the reverse order of removal and adjust the brakes.

Heavy Duty
  1. Raise the vehicle and install jackstands.
  2. Remove the wheel. Loosen the rear brake shoe adjustment.
  3. Remove the rear axle retaining bolts and lockwashers, axle shaft, and gasket.
  4. Remove the wheel bearing locknut, lockwasher, and adjusting nut.
  5. Remove the hub and drum assembly from the axle.
  6. Remove the brake drum-to-hub retaining screws, bolts or bolts and nut. Remove the brake drum from the hub.

To install:

  1. Place the drum on the hub and attach it to the hub with the attaching nuts and bolts.
  2. Place the hub and drum assembly on the axle and start the adjusting nut.
  3. Adjust the wheel bearing nut and install the wheel bearing lockwasher and locknut.
  4. Install the axle shaft with a new gasket and install the axle retaining bolts and lockwashers.
  5. Install the wheel and adjust the brake shoes. Remove the jackstands and lower the vehicle.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 32; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 32; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

May 08, 2011 | 1991 Ford F250

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

2 Answers

How to replace rear wheel bearings


don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
  1. Remove the hub grease cap (1131) from the wheel hub.
  1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
  1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
  1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
  2. Remove the wheel hub from the rear wheel spindle.

Feb 06, 2010 | 1990 Mercury Topaz

1 Answer

How to install wheel bearing hub assemble (front)1998 on a ford escort


front or rear?

Assuming rear, on the brake drum:

Hub Removal
  1. If equipped, remove the brake drum (1126) ; refer to Section 206-02 . If equipped, remove the rear disc brake rotor (2C026) ; refer to Section 206-04 .
  1. Remove the wheel hub.
    1. Unstake the rear axle wheel hub retainer.
    1. Remove the rear axle wheel hub retainer and discard.
    1. Remove the wheel hub (1104).

Nov 05, 2009 | 1998 Ford Escort

1 Answer

Rear drive axle hub removal on a 1994 318i


Need to be pressed off Take whole assembly off and press hub out of bearing Crack retaining ring behind bearing with a cold chisel Press hub back on to new bearing

Jul 09, 2009 | 1996 BMW 318

1 Answer

Bad right rear axle. Need to know how to replace axle.


Dana or Ford axle?

Ford here:
SECTION 205-05: Rear Drive Halfshafts 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Halfshaft
Special Tool(s) s2n~us~en~file=st2258a.gif~gen~ref.gif Protector, Differential Seal
205-506 s2n~us~en~file=st2272a.gif~gen~ref.gif Remover, Front Wheel Hub
205-D070 (D93P-1175-B) or equivalent s2n~us~en~file=st2309a.gif~gen~ref.gif Remover, Halfshaft
205-502
Removal and Installation
NOTE: This procedure applies to both rear halfshaft assemblies.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not loosen the rear axle wheel hub retainer until after the wheel and tire assembly are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied.
    With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. NOTE: Have an assistant press the brake pedal to keep the axle from rotating.
    Remove and discard the rear axle wheel hub retainer and the washer.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the brake hose, do not allow the disc brake caliper to hang suspended from the hose.
    Remove the brake disc.
    1. Remove the two bolts and lift the disc brake caliper and brake pads off the brake disc.
      • Using mechanics wire, position the disc brake caliper out of the way.
    1. Remove the brake disc.
  1. Remove the bolt retaining the parking brake cable bracket to the frame.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Cover the stabilizer link bolt threads and the nut to prevent boot damage when removing the halfshaft assembly from the vehicle.
    Using a rubber hose approximately 37.5 mm (1.5 in) long, cover the stabilizer link bolt threads and nut.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The bolt that retains the upper ball joint to the knuckle is longer and it has fewer threads than the bolt that retains the toe link to the knuckle. Switching these bolts during installation will prevent the pinch arms on the knuckle from correctly retaining the toe link to the knuckle. This may cause the toe link to separate from the knuckle during vehicle operation. Failure to follow these instructions may result in personal injury.
    Remove the pinch bolts and disconnect the toe link and upper ball joint from the knuckle.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the rear suspension upper arm to prevent boot damage when removing the halfshaft assembly from the vehicle.
    Using a wood stick, approximately 450 mm (18 in) long and 25 mm (1 in) wide, support the rear suspension upper arm.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the outboard CV joint separates from the hub the knuckle will continue to pivot until the brake backing plate presses against the suspension lower arm. To prevent damage to the brake backing plate, immediately after separating the outboard CV joint from the hub, rest the knuckle on a cushioned support that is tall enough to keep the backing plate from pressing against the suspension lower arm.
    Separate the outboard CV joint from the hub and rest the knuckle on a cushioned support.
    1. Using the special tool, press the outboard CV joint until it is loose in the hub.
    1. Remove the special tool.
    1. Separate the outboard CV joint from the hub.
    1. Rest the knuckle on a cushioned support.
04ab306.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the axle shaft oil seal or the machined sealing surface on the inboard CV joint housing.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow the splines on inboard CV joint housing to touch the axle shaft oil seal.
    NOTE: A circlip retains the inboard CV joint housing to the differential side gear in the axle.
    Using the special tool, disengage the inboard CV joint housing from the differential side gear.
c231bc2.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the axle shaft oil seal, install the special tool before removing the inboard CV joint housing from the axle.
    Install the special tool.
50c5d1d.gif
  1. Remove the halfshaft assembly from the vehicle.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the axle shaft oil seal, install the Differential Seal Protector before positioning the inboard CV joint housing in the axle.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always install the halfshaft with a new retainer circlip and a new rear axle wheel hub retainer.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never use power tools to tighten the rear axle wheel hub retainer.
    To install, reverse the removal procedure.

Apr 17, 2009 | Ford Explorer Cars & Trucks

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

1 Answer

Rear hubs


In the center of the hub is the axle retaining bolts, 8 I think, remove them and pull the axle out, under that is a giant nut that retains the hub, it requires a quite expensive special tool to remove and re-install correctly, that huge nut retains the entire hub/brake drum assembly. Replace th grease seal and check the axle bearing while you have it apart.


Please rate this solution.

Oct 19, 2008 | 2001 Ford F350 Super Duty SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...