Question about 1998 Chevrolet K1500

1 Answer

98 silverado turns over will not fire

Just rebuilt motor. it turns but no spark.

Posted by on

  • 3 more comments 
  • scooby_dunn Nov 19, 2008

    changed ignition switch coil everything but distributor

  • yellowhammer Dec 05, 2008

    99 S-10 Blazer just rebuilt the motor engine cranks but wont run. No spark at the coil. Coil has constant power w/key on but no signal voltage on the other side. Coil ohms out correctly as well. replaced ignition module too. HELP PLEASE

  • sixbeer69 Feb 13, 2009

    i have the same problem but on a 98 1500

  • nick63079 Feb 13, 2009

    98 silverado good spark and fuelandoil pressure but wont fire

  • paul erickson
    paul erickson May 11, 2010

    did you get your problem fixed

    if not let me know we can work you threw it

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 276 Answers

Check out the ignition switch it needs replacement or intence cleaning.

Posted on Nov 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pulled the motor out of automatic 98 base v6 mustang and put the motor into a standard 98 base v6 mustang and now its not firing, what could be the problem?


Crank sensor, coil, ignition module, Or the distributor, If it has one. This for fire to the spark plugs. Being both were 98's. You could have purchased a bad engine. Check compression.

Apr 14, 2016 | Cars & Trucks

1 Answer

98 silverado intake gasket swap...truck ran now wont start


check all connections where you did the work and make sure no wires are loose or were barely plugged in possibly.

Dec 27, 2013 | Cars & Trucks

1 Answer

Only getting fire on number 4


did you check for spark in thos coils?

Apr 03, 2013 | 2003 Nissan Altima

1 Answer

98 dodge ram 1500 5.9 truck has been sitting for 2 years with a blown ****** got the ****** rebuilt and installed it back in the truck but wont start has spark and fuel at rail but injectors wont fire


98 so its a older vehicle ?? Well i know nothing about layout of this american vehicle but for its age check the fuel rail as on the end is a vacumn controlled valve so make sure its connected and the vacumn pipe isnt cracked or perished ,Anything else i have no idea sorry dont see these motors here in spain very often unless its on a imported camper van but these are normally all diesel ,have seen a 7.2 litre ford E350 petrol though but running on a gas conversion

Mar 09, 2013 | 1998 Dodge Ram 1500 4WD

1 Answer

Car not firing


Most likely the valves were bent.
When you attempt to start the motor does it turns over a bit fast and will not sound quit right - Not even attempt to spark up or fire up.
Check engine cylinder compression. The valves were bent when the belt broke.
you will
1. check compression (and when it fails)
2. decide to have the head checked and if possible rebuilt (use new head bolts)
or
3. Look for and buy a low milage used motor
or
4. Look for a rebuilt head

Mar 03, 2013 | 2004 Suzuki Forenza

1 Answer

Engine for 2000 chevy silverado will not start


make sure you have fuel going to the mottor then make sure you have spark to the spark plugs. if no fuel then your filter or fuel pump may be bad. if no spark then your crank sensor is bad . also it may be your timming belt or chain

Jan 24, 2013 | 2000 Chevrolet Silverado 1500

1 Answer

98 tahoe put in rebuilt trans. now no fire to fuel pump wont start blowing fuses


Depending on which fuses are blowing, you may have shorted a wire in the harness to the fuel tank.

Sep 14, 2012 | 1998 Chevrolet Tahoe

1 Answer

I have a 98 ford escort 2 liter it was running great while driving it just died the engine turns has spark fuel but will not fire


did you check your timing belt? Remove the top half of the timing cover. Spin the motor over with the starter see if the camshaft turns. No turn need belt. Leave comment.

Dec 25, 2010 | 1998 Ford Escort

1 Answer

Rebuilt my motor and installed itin the car but wont run


Check for Gas...Check your Timing...You say you rebuit it..was it just the top end, or the whole motor ? I asked, because there is more things to list, but i wont go into too much detail because you might have done most of them anyway..And also check your compression....Goodluck...

Mar 02, 2010 | 1994 Geo Prizm

1 Answer

98 chevy 1500 conversion van turns but gets no spark or fire will not turn over please help


Please re-phrase your question. First you say it "turns" but then you say it "will not turn". Which is it?

Feb 09, 2010 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
1998 Chevrolet K1500 Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...