Question about 2004 Buick Rainier

1 Answer

Replacing a headlight

I need to install a new headlight & would like thorough instructions on how to do so! :)

Posted by on

  • copettiford Dec 12, 2008

    how do you get to the bulb to replace!?!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 193 Answers

Go to your parts store and purchase the new halegeon blub. READ very carefully the instructions on the box. DO NOT TOUCH the new blub lens.

Carefully pull and twist out the old blub and remove it from its base. Using the special material or a glove, install the new blub in the base, and then carefully insert it back into the headlight shell.
Bill

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing halo and hid lighting in an after market headlight


    Aftermarket Projector Headlight How To Replace HID ...

    store.ijdmtoy.com/Aftermarket-Projector-Headlight-HID-Installation.../5...
    Here are some quick tips and instructions on how to install an aftermarket HIDConversion kit into an aftermarket projector headlight assembly. ... Aftermarket projector headlights look almost like an OEM headlight with the exception of the wiring and design. You would need to remove ... images for Replacing halo and hid lighting in an ...

Nov 24, 2015 | 2000 Jeep Grand Cherokee

1 Answer

How do I replace the headlight assembly MN133516


The 2003 Outlander utilizes replaceable (9007) headlight bulbs. If you're looking to replace the bulb(s);
1. Raise the hood.
2. Remove the plastic cover at the rear of the headlamp assembly by rotating it counterclockwise, and pulling it off. This will allow access to the headlight bulb.
3. Twist the bulb socket counterclockwise in order to remove it from the headlamp assembly. Pull the old bulb out of the socket, and use a clean cloth to install the replacement bulb. Do not touch the glass of the new bulb.
4. Place the socket back into the assembly, and twist it clockwise. Reattach the plastic cover, and close the hood.
Are you needing DIY instructions for replacing the entire headlamp assembly? Left (driver) or Right (passenger)?

Jan 18, 2013 | 2003 Mitsubishi Outlander

1 Answer

Instructions for replacing headlight bulb for '98 subaru forester.


Open the hood, reach behind the headlight assembly and carefully turn the lamp assembly counter-clockwise, then remove the pigtail. To install a new lamp, simply do the reverse procedure.

Jan 09, 2011 | 1998 Subaru Forester

1 Answer

Replacing headlight


Inspect/Replace There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.
f19-22.jpg Comparing the old and ther replacement headlamps. To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Jan 02, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

Replacing volvo 240 head light unit


There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.
f19-22.jpg Comparing the old and ther replacement headlamps.
To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Nov 10, 2010 | 1982 Volvo 240 Series

1 Answer

Change low beam headlight


Inspect/Replace There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.
f19-22.jpg Comparing the old and ther replacement headlamps. To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Nov 06, 2010 | 2002 Jaguar X-Type

1 Answer

2002 vw beetle headlight light bulb needs replacing


look under the hood toward the headlight there will be a lever. pull it up (some have a button thing that you push in while you pull up) after you lift the lever, pull the headlight out from the front.disconnect electrical connector. remove black back cover plate remove and install new bulbs( remember not to touch them). replace in reverse order. hardest part is putting it back it. make sure you align the rails and have lots of patience you will get it!

Apr 11, 2009 | 2002 Volkswagen Beetle Turbo S

1 Answer

Need to remove the passenger side headlight assembly on an "06 vw touareg?


There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.

To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).
Hope this helps!

Mar 10, 2009 | 2006 Volkswagen Touareg

Not finding what you are looking for?
2004 Buick Rainier Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...