Question about 1993 Volvo 850

1 Answer

1993 volvo 850.gear position sensor remove conector from housing

Yes i need to know how the wire conector comes out of the housing

Posted by on

  • gizzmo966 Dec 01, 2008

    thanx that did it! the link was a big help! fix me right up.not bad guys.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 128 Answers

Remove the housing from the transmission so it is loose, remove the tie straps and the rubber boot, break off the little tabs under the boot. Get a very thin screwdriver and insert into the other end of the housing, you will see a slot, and depress the tab and pull up on the connector. This is a very tricky little procedure, and difficult to explain, but this link should help..

Posted on Nov 29, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hello! My 1993 Volvo 850 Glt driver seat recline back and no coming back.what is the procedure. The key should in position 1, 2 ?

The cable that runs the seat back has twisted so many times it has disengaged itself from the seat back transmission. Pull the upper upholstery up and remove the cable housing from the transmission. Remove the metal end by trimming it off . Remove the piece of housing from inside the end reinstall the end, crimp it just a little and put it back in the transmission use the button and return the seat to the upright position and use the memory buttons to keep it positioned there.

Feb 22, 2015 | 1993 Volvo 850

1 Answer

DIY how do you change the PNP sensor on a 1994 Volvo 850

Remove battery, battery tray, air filter housing. Disconnect the wiring to the switch. Remove the shifter cable. Install the new switch and align the switch with the Volvo alignment tool. Reassemble.

Jan 03, 2014 | 1994 Volvo 850

1 Answer

Need wiring diagram for map sensor for 1993 850

If its a three wire sensor one is a ground , one is the 5 volt refrence and the other one is the signal .Key on the 5 volt refrence shuld be about 4.8 signal should be under 1 but above .5

May 23, 2012 | 1993 Volvo 850

1 Answer

Engine turns over but won't start on my 1993 Volvo 850-GLT, Distributor not firing. Error code is 314 (Cam Positioning Sensor - faulty or missing)!

Use the shop manual locate its position on the camshaft check it for wear and voltage and any other checks the shop manual says to do.

Apr 07, 2010 | 1993 Volvo 850

2 Answers

I have Volvo 1993 850 GLT odomters salvaged from the junk

Short of buying new, there is no known way of clocking it.

Jul 09, 2009 | 1993 Volvo 850

1 Answer

Code 122 of A&, 93 Volvo 850

I am not a mechanic, but was recently looking into codes for my 1994 850. Here is what I found out...perhaps it will be useful to you if you do not already know this: The A1 313 is for a "Faulty gear position sensor PNP" ; can not find info on the others. My limited understanding is that the other codes refer to different systems; e.g. the A1 is for transmission codes, A2 is for fuel system, etc.

Jan 22, 2009 | 1993 Volvo 850

1 Answer

1993 volvo 850 glt

Have you made sure the rotor is turning in the distributor, as this sound like a cambelt failure.
Sorry to bear bad tidings if this is so.
Paul 'W'
Onyer~EDson(:0) {#><U.K.
Please remember to politely rate my effort!

Jan 21, 2009 | 1994 Volvo 850

1 Answer

Volvo won't shift to second,third or 4th gear

Try to flush out you old trans fluid,see if this helps first.If its brown,that's bad it needs to be red.

Jan 16, 2009 | 1993 Volvo 850

1 Answer

I can't get the gear position sensor plug out of its case

Are you talking about removing the wiring connector out of the housing? Or something different? Let me know, I've replaced many of these and there are a few tricks.


Nov 17, 2008 | 1993 Volvo 850

Not finding what you are looking for?
1993 Volvo 850 Logo

Related Topics:

447 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides