Question about 1993 Jeep Grand Cherokee

2 Answers

1994, HAVING TROUBLE WITH ALARM SYSTEM, SOMETIMES IT WON'T START, WHEN I ADJUST THE TILT WHEEL ALL THE WAY DOWN, THE HEADLIGHTS GO OUT, I NEED WIRING DIAGRAM TO TRACK DOWN THE PROBLEM.

Posted by on

  • carolwilson1 Jan 26, 2009

    I have a 1993 Jeep Ckerokee .the alarm started to go off and lights blink and engine turnes over then quits. How do i reset it or shut off?The engine won't start. I had to unhook the battery to get lights to shut off

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem with my 96.I had to put a new computer on it.And that fixed mine.

Posted on Nov 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I tilt the steering wheel down on my 2003 pontiac grand am the headlights go out


i expect its pulling the wiring loom/connector away from the switch very slightly, remove the cowling and see if there is any sort of cable tie/tape around the wires from light switch if so cut free carefully and tape back up LOOSELY so the wires can move with the tilt of the wheel

Apr 27, 2014 | Cars & Trucks

1 Answer

My low beams don't work, but the high beams do. changed the light bulbs and headlight switch.


the multifunction switch that controls the wiper /turn signals,and high/low beam lights are very common for (when they get a lot of miles on them) for having problems.also I have seen a good number of these pickups that the connector (that plugs into the back of the multifunction switch)had lost the ability to properly hold the wire terminals into the connector causing a poor connection between the switch and the wiring. sometimes this can be verified without removing the column shrouds by (if equipped) tilting the tilt wheel up and down and see if the lights start working . hope this helps,thanks for using fixya

Jan 01, 2011 | 1994 Ford F350 Crew Cab

1 Answer

Car won't always start. Battery is good. Is


If you have tilt wheel the key cylinder has very thin wiring running all the way down the steering coluum. They tend to short out within years of use. Sometimes upon tilting the wheel the car will & will not start. The wiring runs to the security system

Apr 02, 2010 | 1998 Oldsmobile 88

3 Answers

When i turn on my headlights it blows the fuse but all the other lights work till you turn on the headlights


You have a short to ground somewhere. I would start at your headlights and make sure the wires are in good condition. From there I would look at your switch since it's the most used in the system.

Sep 24, 2009 | 1998 Chevrolet K1500

1 Answer

2003 gmc sonoma Day/Night Headlights only turn on when the tilt steering wheel is down and held down.


a problem with your dimmer switch; may be able to adjust it,if not replace it but inspect wiring and connector first

Jul 22, 2009 | 2003 GMC Sonoma Extended Cab

1 Answer

Toyota Camry 1994 No ignition think it may be alarm


disconnect the alarm system from under the dash.battery to starter direct will turn the engine over fine but ignition system still runs through your alarm system.It's also a theft prevent system so your car will not be stolen.The alarm went bad preventing your car from starting.That means putting the ignition wiring back to factory.

May 25, 2009 | 1994 Toyota Camry

2 Answers

Having a problem locating the alarm box


I had problems with an alarm. the ground wire was loose. i deactivated it by disconecting the ground wire. when i repaired the ground connection. it worked well.

May 19, 2008 | 1994 Chrysler LeBaron

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

69199 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...