Question about 1995 Volkswagen Golf

2 Answers

Auto gearbox fault on my mk3 vr6

My vr6 engine runs fine and it goes in to all the gears however the minute i try to drive it grinds loudly to a halt knocking and crunching

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Pull auto trans dipstick out is oil gritty ? then your torque convertor has crashed, burn out.

Posted on Jan 11, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 67 Answers

Did ya brake a cv axle?

Posted on Nov 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fault gearbox


name the fault.
tell the symptoms, there are like 100';s
A/T or M/T
auto or stick
can you drive it?
do all gears work? (car moves in all gears with out RPM going crazy high)
gears grind.
cant shift at all?
what?

Dec 24, 2013 | 2005 Honda CRV 2.2

1 Answer

Grinding/whining noise from gearbox/final drive - fiat 500C Lounge - 2010 model


I think removes the tyre both then check its gear box bearing noise or clutch plate bearing noise

Dec 16, 2013 | Cars & Trucks

1 Answer

Hi I have a 2005 ford focus 2.0 automatic. I was reversing out of my drive no problems put the car into auto and the car jerked forward then made a loud clunking sound and wouldnt go. I can drive the car...


cannot be sure here without a on site inspection but i would hazard a guess and say the flex drive plate has broke around the crankshaft retaining bolts ,its a gearbox out job to repair ,the plate holds the torque converter in position to the engine crank ,Dont get this problem with a manual transmission

Mar 23, 2011 | Ford Focus Cars & Trucks

2 Answers

Geting no drive on my mk3 vr6 golf even in gear replaced slave cylnder


Make sure the air is out of the line. Any air... no clutch.

Oct 03, 2009 | 1993 Volkswagen Golf

1 Answer

Can a replaced non programmed abs affect auto gearbox


The ABS control unit does need to be coded to the vehicle. After coding the control unit, an End-Belt run test must be performed. I know that you will also have transmission faults stored, because the Trans warning is set since the control unit has not been coded
and the control units communicate constantly during engine operation. The trans uses abs input for shift characteristics and helps with power reduction during evasive driving control. A dealer should be able to code and perform the end run test and usually charge about an 1hr fee. They will also need to quick delete other fault memories.

Mar 16, 2009 | 2001 BMW 5 Series

8 Answers

Gearbox fault of Jaguar S Type


hi,change the gear box solonied c.should b ok than ali g autos birmingham 07971335303

Jan 08, 2009 | 2000 Jaguar S-Type

1 Answer

Vw golf Mk3 VR6 gearbox/cooling system


I don't know where your leak is happening but I suspect the transmission fluid attacks rubber and may be leaking from the heater because of softened hoses.
I think the first move I would make is to buy a Haynes or Chilton service manual and spend some time researching how the transmission and cooling systems are related. The books are available at auto parts stores (or on line of course) and cost between $17-$30 US.  

Oct 13, 2008 | 1995 Volkswagen Golf

2 Answers

Can't change to fifth gear. other gears are fine and engine sounds smooth enough. its a 2003 polo actually, not golf. 1.2, manual, petrol


selector forks on the fifth gear are worn out but don,t let a garage take the gearbox out it can be fixed in place . had the same problem on my golf mk3 vr6 get the parts from a scrap yard should take about half an hour in the right hands to fix

Sep 16, 2008 | 2001 Volkswagen Golf

1 Answer

The automatic gear have a delay in changing the speed number four in model 94 VR6


Maybe a stupid suggestion, but check the oil amount in the gearbox. It must be done with the motor running. I did´nt know that and checked it motor off when the level on the dipstick was fine. When I checked it motor running it was too low. I filled it up and the gearbox works fine...

Aug 30, 2008 | 1994 Volkswagen Corrado

Not finding what you are looking for?
1995 Volkswagen Golf Logo

Related Topics:

546 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...