Question about 1997 GMC Sierra

2 Answers

Head lights go off when the switch is turned to on position

When the switch is turned to the park light position the low beam comes on and the park lights, when I move it to the head light position they all go off

Posted by on

  • Anonymous Mar 22, 2014

    replace low beam head lights

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Mine does the same thing, i just kinda got used to it, the brights come on if you pull back on the blinker lever tho right?

Posted on Feb 11, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

J'aimerai entrer en contacte avec pour l'achat de votre vehicule

Posted on Nov 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right low beam headlight does not come on but my right turn signal will stay even tho i diddnt turn it on. If I cut on my high beams the rurn signal cuts off. Whats wrong? Helo


It could be the lamp control module !
Headlamps
Battery positive voltage (B+) is applied at all times to the lamp control module (LCM) through the underhood fuse block HDLP fuse.
When you place the headlamp switch in the HEAD position, the headlamps input to the LCM is grounded. The LCM then applies battery positive voltage (B+) through the underhood fuse block HDLOBML fuse and HDLOBMR fuse, which feed the left low beam headlamp and the right low beam headlamp respectively. When you activate the headlamp dimmer switch by pulling on the multifunction lever until the switch clicks, the high beam input circuit to the LCM in grounded . The LCM then removes battery positive voltage (B+) from the low beam headlamps and supplies battery positive voltage (B+) through the underhood fuse block HDHIBML fuse and HDHIBMR fuse, which feed the left high beam headlamp and the right high beam headlamp respectively.
Check this fuse in the left under hood fuse box first. HDLOBMR Fuse 18 10 Amp. RH Low Beam Headlamp . If the fuse is good check for B+ voltage with the low beams on . Use a test light or volt meter . If you look on top of fuse there are two metal tabs ,check there for B+ voltage , If no B+ voltage the LCM - lamp control module isn't supplying any .
Lamp Control Module (LCM)
Under the left side of the IP, to the right of the steering column
Turn Signal Flasher
Under the left side of the IP, to the right of the steering column
Lighting Systems Component Views in Lighting Systems
Lighting Systems Connector End Views in Lighting Systems
Turn Signal/Hazard Switch
In the left front of the passenger compartment, in the steering column

Apr 28, 2016 | 2000 Buick Park Avenue

1 Answer

No low beam. Good high beam. No day lights. What's wrong?


No on the fuse . The LH HDLP and RH HDLP fuse in the fuse block - under hood, supply battery positive voltage to both low and high beam lamps at all times. For manual operation, when the headlamp switch is in the ON position, the headlamp switch supplies ground directly to the headlamps and to the body control module (BCM) on the headlamp low or high beam signal circuit, depending on the position of the headlamp dimmer switch. The BCM uses this signal to determine if the conditions are present to illuminate the daytime running lamps or park lamps.
The headlamps may be turned on 2 different ways. First, when the driver places the headlamp switch in the ON position, for manual operation. Second, with the headlamp switch placed in the OFF position activating automatic lamp control (ALC).For ALC operation, the BCM receives a signal from the ambient light sensor indicating a low or high ambient, outside, light level. Under low light conditions the BCM grounds the headlamp relay control circuit energizing the headlamp control relay. The now closed relay supplies ground through the headlamp switch to the headlamps and the BCM on the headlamp low or high beam signal circuit, depending on the position of the headlamp dimmer switch. When the BCM grounds the headlamp relay control circuit it also grounds the park lamp relay control circuit illuminating the park lamps. The headlamp relay is grounded at G203.
Daytime Running Lamps (DRL)
The low beam headlamps operate at reduced intensity when in daytime running lamps (DRL) mode. The ground circuit to the switch side of the DRL relay has a resistor in-line to reduce the intensity of the low beam headlamps for DRL operation. The body control module (BCM) receives a signal from the ambient light sensor indicating a low or high ambient, outside, light level. Under daylight conditions the BCM grounds the DRL relay control circuit energizing the DRL control relay. The now closed relay supplies ground directly to the low beam headlamps and to the BCM on the headlamp low beam signal circuit. The low beam headlamps now illuminate with reduced intensity. The DRL relay is grounded at G203. Any time the headlamps are illuminated the DRL will not illuminate. Manual park lamps do not effect DRL operation.

Feb 23, 2016 | 2005 Chevrolet Equinox LS

1 Answer

2006 buick allure , automatic low beams do not come on when key starts car


Headlamps
You can use the headlamps two different ways.
?€¢
Place the headlamp switch in the HEAD position for normal operations


?€¢
Place the headlamp switch in the OFF position for automatic lamp control (ALC) operation. During ALC the low beam headlamps are ON for daytime running lamp (DRL) operation in daylight conditions at reduced intensity or low beam headlamps ON at full intensity with exterior park lamps ON in low light conditions. The ambient light sensor is a light-sensitive transistor that varies its voltage signal to the body control module (BCM) in response to changes in the outside (ambient) light level. When the BCM receives this signal the BCM turns ON just the low beam headlamps at reduced intensity for the daytime running lamp (DRL) operation. A resistor wire is used (CKT312) to reduced the voltage which reduces the light intensity for the DRL's function. The ambient light sensor can also turn ON the low beam headlamps and the exterior lamps for automatic lamp control (ALC). Any function or condition that turns ON the headlamps will cancel the DRL operation (this means no reduced voltage to the low beam lights). Thirty seconds after you start the engine with the headlamp switch in the OFF position, the DRL will perform one of two actions:
?€¢
Illuminate the low beam headlamps at reduced intensity in daylight conditions


?€¢
Illuminate the low beam headlamps and exterior park lamps for low light conditions

The DRL operates when the ignition switch is in the RUN position, the parking brake is not set and the transmission is not in the PARK position When these conditions are met and the DRL ambient light sensor indicates daylight conditions the DRL will illuminate
Should have BCM scanned for DTC'S - diagnostic trouble codes , could have DTC'S stored in memory !
DTC B2645 Ambient Light Circuit
The body control module (BCM) monitors the ambient light sensor signal circuit in order to determine if the daytime running lights (DRL) or the auto headlights (ALC) should be turned ON in the AUTO mode. When the BCM senses the ambient light sensor voltage is between 1.75-4.9 volts, either the DRL will be commanded ON or the ALC will be commanded ON.

  1. Turn ON the headlamps.
  2. Ensure that the headlamp dimmer switch is in the LOW position.
Do both low beam headlamps illuminate?
Is only one low beam headlamp inoperative? YES / NO
IF no
  1. Disconnect the lamps switch assembly.
  2. Install a jumper between the headlamp switch headlamps ON signal circuit and ground.
Do the low beam headlamps illuminate?
Do the low beam headlamps illuminate?
Go to Step 18
Go to Step 7

7

  1. Remove the headlamp module.
  2. Install a fused jumper between battery positive voltage and the switched low beam voltage supply circuit.
Do the low beam headlamps illuminate?
Go to Step 8
Go to Step 11

8

Test for the following in the headlamp module control circuit:
?€¢
An open


?€¢
A poor connection


?€¢
A short to ground

Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 10

9

Inspect for a poor connection at the harness connector of the lamp switch assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 14

10

Inspect for a poor connection at the headlamp module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 15

11

Test for a short to ground in the low beam voltage supply circuit. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 12

12

Inspect for a poor connection at the harness connector of the underhood fuse block. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 17

13

Inspect the inoperative low beam headlamp voltage supply and ground circuit for a high resistance, a short to ground, or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 16

14

Replace the lamp switch assembly. Refer to Headlamp Switch Replacement .
Did you complete the replacement?
Go to Step 19
--

15

Replace the headlamp module. Refer to Relay Replacement in Wiring Systems.
Did you complete the replacement?
Go to Step 19
--

16

Replace the inoperative low beam headlamp. Refer to Headlamp Assembly or Headlamp Bulb Replacement .
Did you complete the replacement?
Go to Step 19
--

17

Replace the underhood fuse block. Refer to Testing for Intermittent Conditions and Poor Connections .
Did you complete the replacement?
Go to Step 19
--

18

Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?
Go to Step 19
--

19

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 3

IF

Sep 30, 2015 | Buick Cars & Trucks

1 Answer

How to turn bright lights off on 2003 cts


Could be a bad dimmer switch or a stuck high beam relay or the ( DIM ) dash integrated module .
Headlamp Low or High Beams Always On

2

  1. Turn the headlamp switch to the OFF position.
  2. Verify that the transmission shift lever is in the PARK position for vehicles equipped with automatic transmissions or the parking brake is applied for vehicles with manual transmissions.
  3. Expose the sunload sensor to a bright light.
  4. Turn the windshield wipers to the OFF position.
  5. Turn ON the ignition, with the engine OFF.
Are the head lamps ON? YES or NO

3

  1. Turn OFF the ignition.
  2. Install a scan tool.
  3. Turn ON the ignition, with the engine OFF.
  4. Turn the headlamp switch to the OFF position.
  5. With a scan tool, observe the Head Lamp Switch parameter in the Dash Integration Module (DIM) Inputs data list.
Does the scan tool indicate that the Head Lamp Switch parameter is OFF?
I would think you probably don't have a GM Tech 2 factory scan tool , this is a very involved diagnostic flow chart an you can't diagnose it very easily without the factory scan tool . You could replace parts an get lucky . I would start with the high beam relay in the under hood fuse / relay center . Do you know what a relay is , not to talk down to you because I don't what you know . The relay is energized by the DIM - dash integrated module . You may want to take this to a ASE certified repair shop or the dealer !
I would



Or
wh
Which

Jul 31, 2015 | 2003 Cadillac CTS

1 Answer

Only one head light works at a time, diferent light in all positions


Most likely the high beam filament is burnt out on your left light, and the low beam filament is burnt out on your right light. My first recommendation would be to purchase a couple of headlamp bulbs, install them and see how they work, then post back if you are still having an issue

Aug 23, 2014 | 2002 Dodge Grand Caravan

1 Answer

2006 Chevy HHR low beams do not work in auto or on positions. However, low beams flash when locking/unlocking the car using the remote. Also, high beams, parking lights, and turn signals all work fine. All...


Your running lights which come on when you are in drive should be the ones flashing when you use the key FOB to lock or unlock vehicle not your head lights. Although unusual maybe both low beam head lights are burnt out or a bad ground, that the only thing that makes sense to me.

Nov 30, 2013 | 2006 Chevrolet HHR

1 Answer

I have a nissan pulsar Q 2001 model. When I turn on the lights the park lights come on but on switching to low beam the lights remain in park. High beam works fine. Where would the problem lie?


hi
the problem may be due to the mid spring inside the light switch which cause the turn on ,of the low beam light .its better to replace the light switch near the steering

Jul 14, 2009 | 1990 Nissan Pulsar

Not finding what you are looking for?
1997 GMC Sierra Logo

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...