Question about 2007 Mercury Mariner Premier 4WD

1 Answer

Replace bulb in 05 Mercury mariner

Do you get to it from the inside or the outside.

Driver side, rear brake light

inside looks sealed?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Two screws on the inside and lightly tug the the assembley off the outside of the car. should pop right off.

Posted on Dec 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace multi-function switch 2005 mariner


The tail light is usually a bulb with lower wattage, so it won't glow as brightly as the brake and turn lights.. There should be one or two other bulbs in either of the two tail assy's. The turn signal can use the same bulb as the brake light. If so, it's up to the flasher assy to direct the lights to both come on, and/or for one to flash if the brake and turn signal is on, e.g.. There could also be a backup light.

So if the brake and turn lights don't operate, look to the fuses, and flasher assy. for possible replacement.

Jun 01, 2015 | 2005 Mercury Mariner Premier

1 Answer

Replace turn signal flasher


Change the bulb first... That's a double filament setup...could be a $2 fix

Jan 27, 2014 | Mercury Mariner Cars & Trucks

1 Answer

Rear driver side running light is not working, but the brake and rear turn signal are working. I have replaced bulb and checked the wiring.


check the front light on the same side is working as their is a fuse for either side of the sidelights .failing which i would need a play as this vehicle isnt wired to europeon standard and uses them funny american electrics with a big stop light switch that interferes with the brake light for the indicator so i would need a play to determine the exact cause ,have you checked the bulb holder ??

Nov 11, 2012 | 2005 Mercury Mariner

1 Answer

Change rear brake light on a 2010 mercury mariner


Well, here is an article which may about how do I replace rear brake pads, I hope it might have help to you.

Aug 01, 2012 | 2010 Mercury Mariner

1 Answer

2008 Mercury Mariner rear axle is leaking. Is there a possibility I can just tighten it down or will it require me to replace it?


You have to loosen the rear suspension on that side

Remove the axle nut & pull the knuckle clear of the axle

Then remove the axle on the side that leaks

Change the seal & replace axle,etc.

Jul 08, 2012 | 2008 Mercury Mariner

1 Answer

How do you change the outside tail and brake light in the rear of a 1997 Mercury grand marquis? Tail light assembly seems sealed. Is there a trick to changing the bulbs or is this a major endeavor?


Move trunk interior inside fenderwell. There are 4 retaining nuts that hold the outer light assy. Remove those nuts and pull assy straight out so as not to damage plastic studs. Rotate bulb socket counterclockwise and and replace with correct bulb

Mar 12, 2010 | 1997 Mercury Grand Marquis

1 Answer

How do i change the brake bulb for my 2007 mercury mariner? I have already removed the 2 screws on the inside section of the rear tail light lens, but something is keeping it connected on the outside of...


Are you positive that there are only 2 screws? If so give a good push with your thumbs near the ceanter of the assembly it should pop out. If not theres another screw that your missing.

Jul 29, 2009 | 2007 Mercury Mariner Premier 4WD

1 Answer

99 mercury mystide had rear running light broken


If the driver's side tail light is working, it's not a fuse. Use a test light to check for power at the bulb holder. One terminal will be for tail light, the other for brake/turn light. If the is constant power for tail light, replace bulb. If no power, trace wiring from bulb holder to driver's side junction. Probable broken wire between the two tail lights.

Jan 16, 2009 | 1999 Mercury Mystique

1 Answer

Cannot replace driver side brake light bulb


how is it installed? from outside, or from inside the trunk? if outside, you may have to remove the lens. but if inside, you may have to remove the entire assembly to get the bulb out.

Nov 13, 2008 | 2000 Mitsubishi Galant

1 Answer

Replacement of rear outside tail light assembly


If you're asking how do you change a taillight bulb, then follow this procedure:

Open the trunk lid.

Disconnect the connectors from the taillights (taillight bulb connectors are visible by looking inside the trunk at the back of the tail lamps.) There may be an interior trunk trim panel that you have to take off but in most cases its just a series of thumb screws that hold them in.


Brake Lights/Taillights: 21/5 W

Rear Turn Signal Light: 21 W

Back-up Light: 21 W

Rear Side Marker Light: 5 W


Turn the bulb sockets 45 º counterclockwise to remove the bulbs.


If you're removing the taillamps with the bumper off there are 3 nuts and screws that hold the taillight to the rear panel of the car that have to come off from the inside of the trunk.
Remove the nuts and screws, then remove the taillight.

hope that answers your question

Aug 15, 2008 | 2006 Volkswagen Jetta

Not finding what you are looking for?
2007 Mercury Mariner Premier 4WD Logo

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...