Question about 2002 Ford Explorer

1 Answer

How can I find the keyless entry code for a 2002 Explorer Limited

I bought the car used in NY, and it runs fine, everything is OK. I want to be able to use the keyless entry (on the outside of the driver's door) but i cannot justify going to the dealer and paying over $100 for the answer.

Posted by on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Contact Ford dealer with vehicle serial number and registration

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 Ford Explorer and I don't know the keyless entry code. I need to know how to reset it


Have you tried getting a hold of the ford dealership they helped me when i called them

Oct 04, 2012 | 1999 Ford Expedition

1 Answer

My boyfriend bought a 1996 ford explorer, from a friend who is now passed away. Every now & then the alarm goes off but he does not have a remote for the alarm or the code for the keyless entry on the...


The security computer box is in the cargo area open the rear hatch on the driverside behind the plastic is the box, it will have the keyless entry code printed on the side.

Jan 18, 2011 | 1996 Ford Explorer

1 Answer

Remove or disable keyless entry code.


this code is located on a module on inside left rear panel where your car jack is located you will need a flashlight to look up on the module there will be a sticker on this module with 5 digits this will be the original factory code to lock or unlock your car . inside your owners manual there is a procedure to change the code .

Mar 19, 2010 | 1994 Ford Explorer Limited

1 Answer

Where is computer nodule to get the factory code for keyless entry pad


The module for the keyless entry system is located behind the glove box. it should be black or white box

Aug 12, 2009 | 2002 Ford Explorer

1 Answer

Can't program Second remote to my Ford Explorer 99


reading your post you mention to "open and close switch"..not sure what refering to...these are the instructions from your vehicles service manual...good luck!

Programming NOTE: All keyless entry remote transmitters (15K601) are programmable and must be set at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Diagnosis and Testing.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 08, 2009 | 1993 Ford Explorer Limited

1 Answer

1993 ford explorer


the keyless entry pad may be an add on from the dealer which was just stuck on therefore comtains a battery need to remove the door panel and check for wires from pad

Sep 14, 2008 | 1993 Ford Explorer Limited

1 Answer

Keyless entry combination


  • 1995 thru 2001 is located in the jack storage compartment in the rear of your Explorer. First remove the panel to the jack storage compartment. Towards the front of this area you should see a metal box this is your auto-lock module(way up front next to your rear left passenger seat). On the back side of this is your 5 digit code factory preset code. It is hard to get to. To see it you will have to loosen, pull, use a flashlight or a mirror but it can be done.
  • Jul 27, 2008 | 1995 Ford Explorer

    2 Answers

    Keyless door pads


    Go to www.customersaskford.com - type in the text box - keyless entry - then press the "ask" button

    Jun 21, 2008 | 2002 Mercury Mountaineer

    Not finding what you are looking for?
    2002 Ford Explorer Logo

    Related Topics:

    274 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    60792 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...