Question about 2004 Jeep Grand Cherokee

1 Answer

Malfunction indicator not turning off

How do I reset the malfunction indicator?

Posted by on

  • noe_alaniz Nov 18, 2008

    I went to Advanced Auto and ran a diaognostic test and the following cods were provided;



    P0051

    P0031



    HO2S Bunch 1&2



    Sencer 1



    heater circut low

  • noe_alaniz Nov 22, 2008

    I was looking to make repairs at home, not at the dealership...

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 109 Answers

That was a good idea getting the VAG codes. You should get to a jeep dealer who can analyze the problem.

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset airbag light


Hey Earl, what's going on ? The air bag module is usually under the passenger seat or the center console ! The only way to turn off the light is with a up grade scan tool , not code reader. An the light is on for a reason , problem with the system ! If you don't know about this don't mess with it , you could deploy an air bag !
The AIR BAG indicator, located on the instrument panel cluster (IPC) is used to notify the driver of SIR system malfunctions and to verify that the SDM is communicating with the IPC. When the ignition is turned ON, the SDM is supplied with ignition 1 voltage and requests the IPC to flash the AIR BAG indicator 7 times. While flashing the indicator, the SDM conducts test on all SIR system components and circuits. If no malfunctions are detected the SDM will communicate with the IPC through the class 2 serial data circuit and request the IPC to turn the AIR BAG indicator OFF. The SDM provides continuous monitoring of the air bag circuits by conducting a sequence of checks. If a malfunction is detected the SDM will store a diagnostic trouble code (DTC) and request the IPC to turn the AIR BAG indicator ON. The presence of a SIR system malfunction could result in non-deployment of the air bags. The AIR BAG indicator will remain ON until the malfunction has been repaired.

Feb 06, 2015 | 2005 Chevrolet Tahoe

1 Answer

MY honda 2003 crv the malfunction indcaitor lamp has turn on,what should ido thanks.


take it to an auto parts store and allow them to put it on a computer they can tell you what cause it to light and reset it for you aswell

Aug 13, 2012 | Honda CR-V Cars & Trucks

1 Answer

Nissan micra malfunction indicator fault


You must now get the system control module scanned for the fault code(s) that are set in its memory when the check engine light was turned on by the system.

May 25, 2012 | Cars & Trucks

1 Answer

Malfunction Indicator Light is on in my 2003 Hyundai XG350. It is not blinking. Won't have money to repair for a week. Can I still drive it? If not, are there any affordable service centers that offer...


When a 'check engine light' (MIL=Malfunction Indicator Lamp) is turned on, there is a DTC (Diagnostic Trouble Code) set/stored in the ECM/PCM (Engine Control Module/Powertrain Control Module). This code identifies which engine management system component/function experienced a malfunction. Once you pull/read this code, you may begin diagnosis.

Sep 11, 2011 | Hyundai XG350 Cars & Trucks

2 Answers

Tire pressure light does not go off. how do i reset? also on the hatchback lift the button doesn't work. i can remove the inside cover and manually open it by manually sliding the switch. how do i...


All you have to do to reset the TPMS light is make sure all your tires are set around 35-38 psi then drive it a a couple miles and the light will turn off. If it is blinking then you have a sensor issue and you will have to take it to the dealer. The tire pressure warning light is yellow not red."Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow"

Jun 23, 2011 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

Malfunction Indicator light is on. Every thing seems fine except for that, any ideas?


{: ) If the malfunction indicator light is on, it means that your engine modules had detected inconsistencies , specially the emission systems. The engine control modules continuously monitor signals from various sensors and makes constant calculations based on predetermined calibrations. If the feedback gathered is in conflict with its programmed instructions, it will set a code and will request the cluster to turn on the malfunction indicator light.
You may find or feel that your engine is working fine, at the moment, but this issue shoud not be ignored. Small things can become worse if not anticipated earlier.
Tou can try this: Turn off all loads and the ignition switch. key out. Open then close driver door. Wait for 1 minute to reset. Then try to start, and check if the light will go off. If not, its advisable to have your vehicle scanned forn codes to determine the cause.

Feb 23, 2011 | 2003 GMC Yukon XL

1 Answer

Malfunction indicator lamp in my toyota corolla is on how i fix?


The check engine light also called the malfunction indicator comes only when the computer control unit (called the PCM) senses a fault in the electronic controls of the engine and/or the emission system, there are about 200 possible faults that turn the light on, to know what has developed a problem you must have the system tested, this is called an OBD2 fault code test, Kragen and Autozone parts stores do this testing for free.

May 27, 2010 | 2002 Toyota Camry

1 Answer

Malfunction Indicator light


usually a sensor has gone bad. have it check by a mechanic on the computer.

Mar 29, 2010 | 2003 Subaru Forester

2 Answers

What does code 1-p0650 mean?


P0650 Malfunction Indicator Lamp (MIL) Control Circuit Malfunction

Malfunction Indicator Lamp (MIL) is located on the instrument panel. When the ignition switch is turned ON without engine running, MIL will light up. This is a bulb check. When the engine is started, MIL should go off. If MIL remains on, the on board diagnostic system has detected an engine system malfunction.

Possible Causes:
  • Harness or connectors (MIL circuit is open or shorted.)
  • MIL bulb may be faulty
  • May 10, 2009 | Hyundai Accent Cars & Trucks

    1 Answer

    The malfunction indicator light


    Don't reset the battery, as it will only remove the error code but does not fix the problem. You may want to locate a store that can
    check obd 1 (1995 and older).

    Aug 18, 2008 | 1995 Toyota Camry

    Not finding what you are looking for?
    2004 Jeep Grand Cherokee Logo

    Related Topics:

    140 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    61168 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...