Question about 1996 Jeep Grand Cherokee

1 Answer

No front lights work

When i use my turn signals all 4 turn signals light and the indicators on my dash flash including the highbeam indicator. when i turn on my headlamps or parking lamps i have no lights on the front, and only parking lamps on the back. the indicators for all 4 of the turn signals light as well as the highbeam indicator. i replaced the multifunction switch and tried a new headlight switch. i also replaced all 4 double filament bulbs on the exterior of the vehicle.

Posted by on

  • mibase29 Nov 22, 2008

    My rear brakes will not turn off.

  • pfboyd Dec 01, 2008

    the problem turned out to be a connector block under the pcm near the air filter. when i started to troubleshoot the wiring harness i noticed the connector was burned and also 2 wires had corroded off the connector block. the relays just jeeps spoke of are only on the fog lamp equipped vehicles and the wires to them dead end at this connector. i removed the connector and spliced the wires together and the problemn is solved. thank you for your help.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 74 Answers

Check the headlight relays under the hood also fuses under the hood and in the interior fuse pannel.

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have two questions, first my speedometer won't light up, and my high beems won't stay on. And when I put them on it knocks out the headlights. Please help


18538624 Indicators and high beam lights on dash cluster ...

surf.dev.kinday.ru/.../t18538624-indicators_high_beam_lights_dash_clu...
18538624 indicators and high beam lights on dash cluster turn on and wont turn off. ...The high beam indicator light stay on my dash, I have a 2002 HD night train. ... wontwork and the blue indicator light wont light up when the switch is turned to high beams.. the lights ... remove install instrument cluster speedometer cable.

Cluster/Gauge lights out, highbeams dont work, no fuses ...

www.rx7club.com/.../cluster-gauge-lights-out-highbeams-dont-work-no-...
Feb 17, 2012 - My gauge lights decided to go out one night and I can't find any reason why. ... are on works on my dashboard but the lights behind the gauges don't (speedometer/rpms/gas/temp) and my highbeams wont work. .... My foglights stay onwith the headlights. ... If that's the case someone hacked up some wiring.

Oct 24, 2015 | Cars & Trucks

2 Answers

02 Buick LeSabre Ltd. Rear flashers work (blinking rapidly), front bulbs stay on, inside indicators also flash rapidly. Replaced control module under the dash. Did not help. What else could it be?


Hi there., when flashers/indicators work rapidly on the dashboard you should check whether it is the same on the actual bulds. Fadt flashing is usually a sign of a bulb failure somewhere. If everything is functioning ok externally I would consult a competent technician for a diagnosis.

Jun 08, 2015 | 2002 Buick LeSabre

1 Answer

Brake/Signal Lights Problem.


Sounds like a ground problem to me. Bulbs are not getting there ground to complete the circuit so they backfed through the other bulbs.

Oct 23, 2012 | 1998 Acura RL 3.5

1 Answer

Left signal lights do not work on 2005 sts


Check for power at the light socket aswell as grounds

Jun 16, 2012 | 2005 Cadillac STS

2 Answers

1992 Cadillac Brougham 5.0 L V8 RWD, turn signal don't work.


The turn signal switch is most likely the problem,but change the flasher for the turn signals first,some times this is all that it is.

Jun 11, 2010 | 1992 Cadillac Brougham

1 Answer

1998 wrangler turn signal/brake light short


your socket may not be grounded properly, I have seen this before, and the simplest way to fix is change the socket with a new one.Not another used one it may also be bad.

Jul 30, 2008 | 1988 Jeep Wrangler

1 Answer

Ford Taurus Signal light failure


i can tell u this the multifuncion switch is in the steering colum signals,highbeam flash to pass and wipers chuck

Jul 09, 2008 | 1998 Ford Taurus

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

378 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...