Many of these Hyundai exhaust manifolds are cast steel not iron. Cast steel can be welded! It will still probably need to be removed to be repaired but it is an easy repair. I do recommend grinding a "V" groove where ever can see a crack and then welding up the V grooves. You can use stick, wire feed or probably even gas welding but I'd try to avoid gas welding it.
Use lots of penetrating oil on those exhaust studs and lots of patience. Don't break any of the studs. Try the other manifold. If it won't fit, put the old cracked one back on until you can find one that does fit.
SOURCE: 2000 Hyundai Accent
00-30-001 2000 ACCENT DMTL DIAGNOSIS: DTC CODES P1401, P1402 AND P1403
p1402 - dm-tl air pump motor is shorted or disconnected.
2000 model year accent is equipped with a new enhanced evaporative emission system. this new system is capable of measuring leaks as small as 0.020" diameter. the new system pressurizesthe evaporative emission system with a diagnostic module for tank leakage (dm-tl), while the previous model's system appliedengine vacuum through the purge valve to detect system leaks.
service information
vehicles that have the check engine light illuminated and have dtc p1401, p1402 and p1403 stored in the ecm should have their electrical systems diagnosed related to the appropriate dtc. these codes are not related in any way to an evaporative emission system leak. the conditions that set the diagnostic codes areas follows:
p1401 - dm-tl air pump motor current draw is higher or lower than expected (normal = 17-36 ma).
p1402 - dm-tl air pump motor is shorted or disconnected.
p1403 - dm-tl changeover valve is shorted or disconnected
SOURCE: installing new brake pads on 2000 hyundai Accent GL
REMOVAL 
1.
Remove the lower bolt and lift the caliper assembly up and secure it with a wire or some other retaining method.
2.
Remove the pads.
CAUTION: Do not depress the brake pedal while disassembling the pads
INSPECTION
1.
Check the pads for wear or oil contamination and replace, if necessary.
•
The pads for the right and left wheels should be replaced at the same time. Never "drop" or intermix brake pad sets.
•
All four pads must be replaced as a complete set.
•
When replacing the brake pad, check for deformation. When replacing the guide spring, use a new one or the used one after cleaning away foreign material.
2.
Check the pad for damage or deformation.
Brake pad thickness:
Standard value: 9 mm (0.354 in.)
Service limited value: 2 mm (0.0787 in.)
INSTALLATION
1.
Install the pad clips.
2.
Install the pads onto each pad clip.
3.
Insert the piston in the cylinder using the Special Tool (09581-11000).
4.
Install the new pads. The shims are attached to each pad as illustrated
Be careful so that the disc or pad isn't contaminated by grease.
5.
Install the bolt and tighten to the specified value.
Tightening torque
Guide rod bolt: 22~32 Nm(220~320 kgf·cm, 16~24 lb·ft)
SOURCE: Hyundai Accent 2000 shows overdrive OFF( OD OFF)
There is a button on the shifter that turns the OD off and on.
SOURCE: hyundai accent, location of fuel cut off
hi from uk location of fuel safety shut off valve/switch on uk r/h drive accents is on the engine bay bulkhead in front of drivers side it is a square box with red rubber top press button may be on opposite side on l/h drives ? if activated? just press button till click ? to reset these normally only cut off on impact ? to stop elec fuel pump continuing delivering if involved in an R.T.A fire prevention
SOURCE: free owners manual for hyundai accent 2000
Go to hyundaiusa.com and then click on OWNERS on their menu bar. Then create a new account for your specific Hyundai vehicle year and model. Once you successfully log into your account, under the My Vehicle page you should see an underlined link labeled "Owners Manual". Clicking on this link, you will then be able to download a complete PDF version of the original owners manual.
http://schematicsdiagram.blogspot.in/2012/03/this-is-how-system-operates.html
This will help.
Thanks.
200 views
Usually answered in minutes!
×