Question about 2000 Daewoo Lanos

Open Question

2001 Daewoo Lanos check Engine light flashing

I have a 2001 Daewoo Lanos in which I just had the timing belt, cam sensor and harmonic balancer replaced. I picked it up last night and on my way home it died at a stop light I was able to restart it and since the place had closed shortly after I left I drove the rest of the way home. On my way the check engine light began flashing. Once I turned the car off and back on the light didn't come back on until I had driven over 10 miles. Is this flashing something I need to worry about? What could it be?

Posted by on

  • yadayada
    yadayada May 11, 2010

    If the light is flashing then there is a problem, have a test run by Kragen or another parts store like it, it is free, post the trouble codes back here, but I would really make the repair shop do this work, they did something wrong

×

6 Suggested Answers

  • 6 Answers

SOURCE: reset passcode for radio of 2002 daewoo ,lanos

MINE CAME ON A SMALL METAL TAG ON THE SPARE KEY

Posted on Jul 16, 2008

  • 68 Answers

SOURCE: 2002 DAEWOO LANOS PROBLEM

hi andrecti
im dave

check to see if your timing belt is broken. there should be an access hole usually a rubber cap that you can remove to see it. if there is no access hole remove the screws of the timing belt cover and open it enough to see the belt without breaking the cover. If the belt looks ok be sure there is enough tension so that it is not skipping over the camshaft pulley.
check your ignition components for dampness or to see if they are faulty (spark plugs, wires and ignition module and coil packs).

Posted on Jul 20, 2008

jrosario
  • 2 Answers

SOURCE: !999 Daewoo Lanos

201b665.jpege046938.jpeg

It verifies well the year, it is of one of 1999

I hope that it should serve you

Posted on Oct 21, 2008

  • 1 Answer

SOURCE: User manual for daewoo lanos car

Need code to work radio. Replaced the battery and it is asking for a code for the radio to work

Posted on Feb 12, 2009

emjem74
  • 162 Answers

SOURCE: Daewoo Lanos Engine Number

should be on a small seperate plate located no the front of the engine compartment. if not there then check on the back of the engine compartment for a small section with your serial stamped into it. if there are none of the above then i would check for stolen recovered.

Posted on Feb 25, 2009

juggernautxt
  • 145 Answers

SOURCE: 2001 daewoo lanos check engine light

oil is non conductive so I doubt that's the problem, but the oil leak should be fixed to reduce problems down the road.
as for the misfire could be a couple things, fouled plug(s), a plug wire(s) that has cracks, or even valves that are not seating which i doubt from your explanation.
I would change your plugs and wires first, and fix oil leak. if this does not fix the issue there are other things going on.

Posted on Apr 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change a timing belt on a 2000 daewoo lanos 1.4 e tec


If this is an "interference" engine and the belt broke while running you may have major engine damage. If non-interference, buy shop manual to give all details and torque values for this very important procedure.

Feb 09, 2015 | 2000 Daewoo Lanos

1 Answer

Where is the crankshaft sensor location on lanos 2001 ? I changed my camshaft position sensor and the timing belt, but the engine light still on with the same code and the mechanic said it's the...


both the single cam and twin cam engines use the teeth on the crank pulley for crankshaft sensor which is bolted in bracket attached to block near oil pressure switch, hopefully you didnt dent(bent) teeth on crank pulley from dropping it or putting pulley down a bit roughly because they bend really eazy.
also is the crank pulley bolted up in correct position?
is the timming belt tension correct from when you did cam belt?
if tension wrong or timming out by a tooth it will set crank sensor codes, even possibly cam sensor codes and if you get timming out more than 3 teeth either way(advanced or ********) you will bend valves.

stevenhurc_26.jpg

Sep 05, 2011 | 2001 Daewoo Lanos

1 Answer

Camshaft position sensor a bank 1 circuit low input. what is it and where is it located


its on the back cam under the timing belt cover on the one i done last week with a timing belt change

May 16, 2010 | 2001 Daewoo Lanos

1 Answer

No treads on harmonic balancer. Should there be treads on the harmonic balancer because my serpentine belt came off and upon reinstalation properly I found that the belt had treads on the serpentine belt,...


the pulley on the crankshaft should have grooves in it for the belt, otherwise the belt will not turn. is the pulley broken off, get back to me. there are NO technical servise bulletins on this item,if you need more help get back to me, Thanks Ray

Dec 10, 2009 | 2001 Oldsmobile Aurora

2 Answers

I changed the harmonic balancer and now it is terribly out of time. Didn't touch any timing belts, distributor or the like. Any advice?


There may be a magnet on the harmonic balancer for the crankshaft sensor,

The cam and crank sensor call for spark to the plugs..

Some cars you need a Harmonic Balancer Installer Adapter,
to make sure everything is lined up and gaped..

Check the crankshaft sensor for damage from inproper install, also check the wires going to sensor,, some times the harmonic balancer are such a Pain!! to come off the sensor or wires get damage in the battle.






Nov 30, 2009 | 1995 Geo Prizm

1 Answer

Where is crankshaft sensor in 2000 daewoo se


on single cam engines it is bolted to block near front of engine next to harmonic balancer pulley(crank pulley)
on twin cam engines on type lives in block under front engine mount air con compressor and power steering bracket
the other lives in rear section of engine block (trans end) just above sump near oil filter

Jul 02, 2009 | 2000 Daewoo Lanos

1 Answer

CAMSHAFT


on single cam engine its inlet manifold side just behind cam gear rear cover bolted into cam box cover
twin cam its behind cams in middle front of engine in centre of rocker cover remove cover over h.t.leads this one is eazy but tricky due to bolt inside cam belt cover

Jun 28, 2009 | 1999 Daewoo Lanos

1 Answer

2001 daewoo lanos check engine light


oil is non conductive so I doubt that's the problem, but the oil leak should be fixed to reduce problems down the road.
as for the misfire could be a couple things, fouled plug(s), a plug wire(s) that has cracks, or even valves that are not seating which i doubt from your explanation.
I would change your plugs and wires first, and fix oil leak. if this does not fix the issue there are other things going on.

Apr 22, 2009 | 2000 Daewoo Lanos

1 Answer

Instaling a timing belt on 2002 daewoo lanos


I have a 2001 Lanos and I've replaced my belt twice (after breaking the first one at speed and having to replace the engine). The two cam gears have timing marks that should point towards each other. If you hold a ruler up with the edge of it passing through the center of the cam shaft bolts, the timing marks on each cam should be lined up on with the edge of the ruler and pointing towards each other. The crankshaft gear (not the big pulley) has a small triangle timing mark on it that should point almost straight down. There is a V cut into the oil pan that actually should line up with the cranshaft timing mark. BE VERY CAREFUL because if you rotate the crankshaft independently of the cams, you can tear up the valves very quickly.

Dec 05, 2008 | 2002 Daewoo Lanos

Not finding what you are looking for?
2000 Daewoo Lanos Logo

Related Topics:

562 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

yadayada
yadayada

Level 3 Expert

60541 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...