Question about Mazda 323

1 Answer

The cluth only occasionaly will not disengage. It will work perfectlty for a week or so the as you are driving and go to change gear the pedal goes to the floor with no resistance but does not engage the clutch. The master cylinder appears ok and does not leak oil. The local Mazda dealer cant find the problem.

Posted by on

  • Anonymous Jan 11, 2009

    I too have this problem everything was fine then as i was driving my car i went to shift and i put my clutch to the floor b/c there was no resistance and it would not allow me to shift.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 21,949 Answers

I would change the master cylinder,or fit new rubbers as it sounds like the rubber is turning in the bore or its just worn ,beleave it or not the rubber can actually wear the metal away

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My gear shift was extremely hard to get out of gear. When i did get it out, it week not go into any gear at all


Clutch maybe not fully disengaging; does car want to drive forward at a stop with clutch pedal pressed to the floor or smell burunt smell after long stop and go traffic?

Jun 06, 2015 | Cars & Trucks

1 Answer

Overdrive goes on off by itself?


Try this:
place shifter from D4 to D3 don't change the gaz pedal keep steady .if you have a RPM gauge see if rpm change a lot
if yes then it,s not the fourth gear overdrive it's the TCC torque converter clutch apply and disengage depend on load on engine and it's normal function
have someone good technician a test drive
hope it help

Oct 17, 2014 | 2004 Pontiac Vibe

1 Answer

Car will not engauge into 1st or 2nd gear


the gear grinding noise is because the clutch plate is not fully disengaging and the input shaft is still driving. If you did not use the same length of push rod then the slave cylinder is not moving enough to disengage the clutch. Check it out that with the pedal on the floor the piston in the slave cylinder should be almost to the edge of the slave cylinder . That is where It should be to be working properly

Jan 13, 2014 | 2004 Pontiac Grand Am

1 Answer

Started off with cluth sticking to floor.would have to pull clutch pedal back up with foot. truck would stick in gear. even with clutch fully depressed. seemed like spring had disconnected from clutch...


your clutch uses a hydraulic master and slave cylinder to disengage. It is likely that the slave has been leaking and the reservoir gone dry, thus allowing air into the system and reducing effectiveness. Check the clutch master cylinder reservoir (near the brake reservoir) fluid level. If low, also check the slave cylinder at the clutch for leakage. If leaking, replace the slave and bleed the system. If you need procedures or have more questions, please let us know.

Sep 25, 2010 | 1994 Nissan Pickup

1 Answer

Problems with clutch master cylinder on a suzuki grand vitara 2007 after replacing clutch master cylinder was ok for 6 weeks now no clutch pedal again!


I too am having problems with my 2006 GV clutch master cylinder. I noticed gradually over several weeks the gears and clutch pedal were degenerating and then the cluth gave completely. My mechanic took a look around and said the cylinder is the cheapest one he has ever seen, it's just a piece of plastic apparently! Is going to hopefully get the part this week or next, though he said as it's such a cheap and nasty part its likely it will happen again in the future. Not happy!

Jan 31, 2010 | 2007 Suzuki Grand Vitara 4WD

1 Answer

After traveling about 8km my car wont go into 1st or reverse gear. when it is cold it goes into all the gears fine. when i switch the car off it will go into gear. we did put a new(aftermarket clutch) in a...


Cluth cable ajustment if equiped.Some cars have a cluth cylender if your model has the cylender no ajustment is available.If you had your cluth changed at a garage you might consider takeing it back in for ajustments.If you changed the clutch check cluth cable for ajustment if your car is equiped with cable if not i would perhaps remove the transmission and inspect clutch for loose clutch plate or release bearing might not be seated properly hope this helped you.

Dec 24, 2009 | Mazda 323 Cars & Trucks

1 Answer

After being stored clutch willnot engage


do you mean wont disengage? does the pedal feel normal, or like its pushing nothing?cant put it in gear? or goes in gear but wont move?. if you put it in gear but car wont move, the clutch is toasted. if you can put it in gear with the engine off, but not when its running, check the clutch master fluid. if its low or out, then the slave or master is leaking and you will need to replace both. if the clutch arm IS working, and the pedal feels normal, sometimes you can put in gear, and start it with the clutch pedal depressed and drive it, and goose the gas to "break the disc loose"

Oct 14, 2009 | 1997 Suzuki Sidekick

2 Answers

5 speed manual transmission wont shif gears while running


You probably have air in the system. You need to bleed the air out of the system so that it will disengage your clutch. The air in the system is compressing and, therefore, the slave cylinder can't reach the full extension.

Aug 04, 2009 | 1998 Pontiac Sunfire

1 Answer

BELIVE ITS A BAD CLUTH PLATE ON MY 1998 SUZUCKI SIDEKICK


Do u have play in the pedal? when does the clutch start to engage when u let it out to move? close to the top means the clutch plate is worn out.

Mar 15, 2009 | 1998 Suzuki Sidekick

2 Answers

I have a 2002 renault laguna, every now and again the cluth pedal stays in the down position and the car struggles to go in gear, once i lift the pedal back up into the normal position the clutch works...


try bleeding the cluth it sounds like you have air in the system.and have a look and se if the brakes and the cluth use the same fluid if there do bleed the brakes to

Sep 20, 2008 | Renault 18I Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...