Question about 2001 Mercedes-Benz C-Class

Open Question

Speed pulse wiring

Need to install a taxi meter on 2007 C180 car,whereby i need to find a cable to connect speedo pulse.is there a place i can do that,especially on the doors.what colour is it?

Posted by on

1 Suggested Answer

  • 1 Answer

SOURCE: wiring diagram for vss

Try American Taximeters & Communications Inc. 21-46 44th St. L.I.C. NY 11101. We just bought a 7800-0572 converter from them, it plugs into the OBDII plug under the dash, it was for a 2006 Ford 500. Good Luck. $150 plus shipping.

Posted on Aug 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cruise control not working


Check cruise control cable under hood is tight enough to pull throttle arm.
Check brake pedal . see if wires to cruise control are still attached to switch on brake pedal.
Check magnets are still on drive shaft if rear wheel drive.
Check hall effect transducer is still in place to dedect magnets spinning on drive shaft.
Check Vacuum tubing is ok on cruise control it pulls the cable in and out .
Check if ignition sensing that wire is connected that senses ignition pulses ( front wheel Drive)
Check if a speed sender device is used on speedo cable to create pulse (front wheel drive ) sometimes used to sense speed on some cruise controls.
Check wiring around plugs and sockets under bonnet.

May 27, 2015 | 1998 Mercury Grand Marquis

1 Answer

I need to install a centrodyne pulse divider in my 2007 dodge caravan to go with my centrodyne silent 610 taxi meter.


Call Lee at Centrodyne he will help you.
The pulse is most easily found on the transmission at the VSS output. It is a connector with two wires, you want the DG/V. Run that to the pulse divider green wire. From the meter, tie the white in the 2 stand cable to the pulse output. Hook up power and ground then calibrate the meter. You should end up in the 33,000 range for calibration.

Feb 05, 2011 | 2000 Dodge Caravan

1 Answer

Odometer not working


Could be that speedo cable has become disconnected or that the inner shaft has broken. The speed cable is connected between the back of the instrument cluster and the left side of the transmission. Check under the car that the cable is securely fitted to the side of the transmission. Disconnect it and and check on the condition of the square drive flexible shaft. The spinning of this inner shaft is what conveys the output shaft speed of the transmission to the instruments. The instrument cluster can be removed but pushing a length of coat hanger wire with right angle turn on its end between the the cluster and the dashboard surround. Turn the coat hanger to hook behind the cluster and pull forward to remove it. Try several points around the cluster. It is best to disconnect the speedo drive cable to withdraw the cluster (after electrical connections have been disconnected. check that the speedo cable is secure to the back of the instruments. If you remove the cluster completely follow the path of the speedo cable. If you have to replace the cable, tying a length of string to the speedo cable end first and posting the string down the cable path will help the re-installation enormously. Simply pull the string whilst reinstalling the instrument cluster until the end of the speedo can be got hold of. Refit the speedo cable to the transmission only after the instrument cluster is back in place.

Oct 17, 2010 | 1990 Mercedes-Benz 190

1 Answer

Ihave just purchased a mercedes c180 esprit 1994, but speedo not working


check the speedometer cable that runs from your speed gauge to the rear side of the transmission..either you have a loose connection or a bad cable

Apr 21, 2010 | 1994 Mercedes-Benz C-Class

2 Answers

My speedometer works sometimes and sometimes it doesnt but the heat one works and gas one works what is causing this?


hi every car has a speedo meter cable in tat a worm gear attached in the wheel so i case of fails the speedo meter works some time and nt work . so u hav to change the speedo meter warm gear

Aug 25, 2009 | 1998 Dodge Neon

1 Answer

The speedo in my 2000 Rav4 doesnt work.


to test vechicle speed sensor.safely raise front of vechicle.block back wheels besure you are on level ground.get some help to do this.you need a digital volt meter set it on AC SCALE.TURN IGNITION ON DONT START ENGINE.TAKE VOLT METER BACK PROB THE VECHICLE SPEED SENSOR CONNECTOR.TURN YOUR WHEEL WITH ONE HAND YOU SHOULD GET 0.5 VOLTS.AS YOU SPIN WHEEL FASTER YOUR VOLTS ON AC SCALE SHOULD INCREASE.IF IT DOES NOT WORK.IF WIRES ARE OKAY.YOUR VECHICLE SPEED SENSOR BAD OR THE MAGNET GEAR IN TRANSAXLE IS BROKE..

Jun 22, 2009 | 2000 Toyota RAV4

1 Answer

2006 Hyundai Sonata. pulse wire for the speedo.


Go to http://www.hmaservice.com/ and register the Sonata (VIN). Then you'll have access to all kinds of data, technical and otherwise, related to your vehicle... ,service manuals, service bulletins, wiring diagrams, etc.

May 13, 2009 | 2006 Hyundai Sonata

1 Answer

Speedo reads slower than actual speed by about 8%


I fixed it. You just need to physically move the speedo hand anticlockwise. Be careful though.

Jun 28, 2008 | 2007 Mazda Speed 3 Hatchback

Not finding what you are looking for?
2001 Mercedes-Benz C-Class Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64052 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...