Question about 2004 Ford F350

1 Answer

2004 F-350 Replacement Oil Filter Cap

Dumb me, when I was changing my oil and oil fiter, I didn't replace the new filter correctly and "tore up" the inside of the filter cap. Where can I get a replacement?

Posted by on

  • kswndsrfr Nov 18, 2008

    No, my problem is with the cap that fits over the new oil filter (paper type). The new oil filter is supposed to lock into the filter cap first, then screwed onto the housing. I (again, dumb and in a hurry) placed the filter onto the housing and screwed the cap down, breaking off the locking parts inside the cap.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 962 Answers

Why not just buy a new filter ? or do you mean the oil plug on the oil pan ?

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change my oil?


Remove filler cap,
lift car
then from under the car remove oil pan drain plug.
Allow oil to drain into an oil waste pan.
Change oil filter also ..located under skid plate..use filter wrench to remove filter. Be careful as filter is full of oil ..drain in waste pan
wipe filter mounting plate clean..put a thin coating of oil on new filter gasket before spinning it on to the mounting plate..hand tighten and then tighten about 3/4 more turn.. reinstall drain plug. do not over tighten or you can strip the threads. Install correct viscosity and amount of oil start engine. let run to get pressure up. shut off engine, check level with dipstick and close cap....you are done.

Feb 12, 2015 | 2010 Nissan Frontier

Tip

How to change the oil in your car


Attention: Read each step completely before you begin that task. Tools Required:
#1: Oil filter wrench or pliers
#2: Small wrench and sockets (Metric sizes for import cars)
#3: Oil collection device (pan or bucket)
#4: Funnel
#5: Cloth rag or paper towels
#6: Jack and stands or ramps
Supplies Required:
-Correct amount and type of oil, and thrust washer if necessary
-Correct oil filter
Step 1: Determine the correct oil type, oil filter type and size, and amount of motor oil for your car. (Information found in owner's manual)
Step 2: Park your car on level ground and turn off the engine.
Step 3: Locate the engine and make the oil pan accessible. (With the use of jack and stands or ramps) Tool #6 required.
kormega_11.jpg
Step 4: Remove oil cap. (Located on top on engine)
kormega_12.jpg
Step 5: Loosen oil drain plug. Collect oil when draining and dispose of properly. (Located on oil pan which is attached to the bottom of engine block, directly below oil cap)
Tool #2and 3 required
Caution: Oil will start to drain and may be hot
kormega_13.jpg
Step 6: Once completely drained (a slow drip), replace oil plug. Install new thrust washer with oil drain plug if necessary. Do not over tighten.
Tool #2 required
kormega_14.jpg Step 7: Loosen oil filter. Collect oil when draining and dispose of properly. (Attached to the side or bottom of engine)
Tool # 1 and 3 required
Caution: Oil will start to drain and may be hot
kormega_15.jpg Step 8: Install new oil filter hand tight. Lube the rubber O-ring on oil filter with motor oil, and make sure the O-ring from the old filter is not still on the oil filter connector.
kormega_16.jpgkormega_17.jpg Step 9: Pour correct amount of new motor oil into engine.
Tool#4 required
kormega_0.png Step 10: Check for oil leaks from drain plug or oil filter.
kormega_18.jpg Step 11: Turn on engine and continue to check for leaks. Tighten oil drain plug or oil filter if necessary.
Step 12: Turn off engine and check oil dip stick to see if the right amount of oil has been added. After removing oil dip stick, wipe clean with rag or paper towel. Reinstall oil dip stick and then remove again to see correct oil level. Then Reinstall oil dip stick again.
Tool #5 required
kormega_19.jpgkormega_20.jpg Step 13: Lower vehicle from jack and stands or ramps.
Step 14: Record the mileage of the car for future reference. (Motor oil should be replaced about every 3 months or 3,000 miles)kormega_21.jpg

on May 03, 2011 | Nissan Maxima Cars & Trucks

3 Answers

Oil leaks from the place oil fiter fit on motor


Perhaps but it could also be a bad oil filter seal. Might want to remove the filter to inspect both the seal and the housing.

Jan 12, 2014 | Audi A4 Cars & Trucks

1 Answer

Where is the oil filter Located on the 2011 Lexus GX460


The oil filter on a Lexus GX460 is a cartridge type filter located at the bottom front of the engine. It is difficult to see without removing the front engine undercover, which is basically a steel plate shield held to the vehicle by 4 bolts. Once the shield is removed, the oil filter housing is visible right behind and just above the stabilizer bar. The housing is positioned sideways and a large pair of channel locks can be used to unscrew the black housing cap. Make sure you have a drip pan ready because a fair amount of oil will drain once the cap is removed. After the cap is removed, it's a simple matter of removing the cartridge filter with your fingers and popping in the new one. A new rubber o-ring should be included with the replacement filter.

Jun 25, 2012 | 2010 Lexus GX 460

1 Answer

How do i do a self oil change on a 1995 jeep grand cherokee


locate oil drain plug on oil pan,engine off. take out oil plug with wrench, drain oil into a big pan or similar. when oil is drained remove oil filter and put new one on, put some new oil on filter seal with finger then screw on to car as tight as you can get it by hand. do not use a fiter wrench to tighten filter only hand tight. use oil filter wrench to take off old oil filter. when filter is on put plug back in oil pan and tighten. then add your new oil to reccomended oil level.

Jul 21, 2010 | 1995 Jeep Grand Cherokee

2 Answers

How to and what tools are nessacery to change oil


oil catch pan hydraulic cat and ratchet with metric sockets adjustable filter rachet lift car front get on under with oil pan rachets and on the motors side of the car you'll find a bolt on the crank pan just a lonley screw on the bottom of a pan close to where your under loosen screw first then put oil pan under try and loosen screw slowly so when it lets go you can cntrol the flow a little so the oil pan can be put in the proper place to catch the oil let it empty till there is nothing but droplets return screw and tighten back on do not over do it the treads on the pan can be harmed if you over tighten then locate filter put oild pan under filter loosen and the same way as the screw do with the fiter . Before putting in new filter on put some fresh oil on the rubber ring and inside just a little so it goes on smooth your finished under the car now go up top hood open you can put car down by now find oil cap and fill in oil

Apr 03, 2010 | 2002 Toyota Camry

1 Answer

How do i change the oil on my 01 vw gti vr6


This engine requires synthetic oil, 5 quarts, and oil filter. Remove dip stick, remove oil drain plug at bottom of engine oil pan, remove filter housing, remove oilf filter and o-ring. Replace o-ring and filter, rub o-ring with some new oil, replace filter housing, replace oil drain plug, pour new oil in at top of engine oil cap, replace dip stick, start engine, run for 45 seconds, turn off, check dip stick to make sure oil is at correct level. You are done, recycle old oil.

Sep 19, 2009 | 2002 Volkswagen GTI

3 Answers

Oil drain plug


It is in the bottom of the oil pan. The oil pan is the bottom most part of the engine. it looks like a pan.

Jun 30, 2009 | 2006 Volkswagen Passat

4 Answers

Oil Filter Location on 2009 Kia Borrego W/3.8 ltr


nazof is exactly right. Totally disregard emissionwiz and clint_carter. I have the exact same vehicle and have changed the oil and filter myself. The filter is located right in the middle, almost up against the firewall, after you pop the plastic engine cover. You must twist off a plastic cap and then pull the filter (a cartridge type) straight up and out. There are two replacement rubber rings that should come with your replacement filter. One goes on the plastic cap (just above the screw threads) and the other much smaller one goes at the end of a plastic rod that is connected to the cap.

Apr 06, 2009 | 2009 Kia Borrego

2 Answers

How do you change the oil filter on a Hyundai Accent 1998/99?


Replace the oil filter after draining the old oil, and" BEFORE "adding new fresh oil, otherwise you'll be dump all that fresh oil, on the ground,while you "TRY to get the new filter installed.

Step 1 Remove drain plug,Drain oil into drain pan
Step 2 Remove oil filter
Step 3 Reinstall drain plug,qnce oil has drained.
Step 4 Fill new filter with oil,lube seal on filter.
Step 5 Install new filter, Add fresh oil to proper level.replace filler cap
Step 6 Run engine check for leaks.
Happy motoring!

May 23, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
2004 Ford F350 Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...