Question about 1998 Jaguar XK8

1 Answer

Install instructions for new window switch module

How does the window switch module come out ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 100 Answers

Drivers side. Pull back the trim inside the door handle pocket, uner the trim there is a philips screw, then the window switch with wood trim pops out, disconnect the connector, swop the sprung wood trim and your good to go.

Posted on Jan 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

1 Answer

2005 trail blazer-power windows won't work and a/c only blows from the bottom


All the power windows are inoperative ?
Power Window System Components
The power window system consists of the following components:
?€¢
Driver door module (DDM)

?€¢
Passenger door module (PDM)

?€¢
Body control module (BCM)

?€¢
LR power window switch

?€¢
RR power window switch

?€¢
Window up and window down relays in each of the rear passenger window switches

?€¢
Window lockout switch

?€¢
Reversible power window motors in each of the doors (circuit breaker protected)

?€¢
LT DOOR CB 25A (System power for left rear window)

?€¢
RT DOOR CB 25A (System power for right rear window)

Are you aware of the electronics involved ? control modules - computers ? Are you good diagnosing electrical problems . Do you own a professional scan tool ?

  1. Install a scan tool.
  2. Monitor the Driver Window Status Data parameter in the driver door inputs list.
Does the Driver Window Status Data parameter display an active state?
Your best bet would be to take your vehicle to a qualified repair shop . For both problems .

The Trainer 24 Power Window Troubleshooting

Oct 26, 2016 | 2005 Chevrolet TrailBlazer

1 Answer

Turn signals do not work, have replaced module, still do not work


Find a wiring diagram an get a DVOM - digital volt ohm meter an do some electrical testing . Videos on you tube on basic automotive electrical testing , how to read a wiring diagram . Then go http://bbbind.com/free_tsb.html free wiring diagrams . What component controls windows an door locks , I know what does , what to see what you think does . The speedometer not working is probably the step motor inside the instrument cluster . New instrument cluster ! Replace the turn signal switch.
The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door. The driver door module (DDM) is the master control for the door lock system but the rear integration module (RIM) contains the program that determines when the lock functions are permitted.
The vehicle is equipped with power windows controlled by the door modules. The DDM receives a window switch request, over the SBI serial data, from either the passenger door module wired to the window switch pressed or from the driver door switch assembly. The DDM checks the Class 2 serial data to see if the status information is correct (i.e. ignition switch position) to permit window operation.
If the status information to permit window operation is correct, the DDM sends the command to the door module controlling the window to move the window as requested.
Windows Power and Ground
The windows are powered by discreet power and ground circuits. These circuits are in the same dedicated connector as the window motor drive circuits.
These systems are very complex and are able to set DTC'S in the controlling module .Your best bet is to take your vehicle to a qualified repair shop .
DTC B3142 LF Unlock Switch Circuit Low DTC B3147 Passenger Unlock Switch Circuit Low DTC B3152 LF Lock Switch Circuit Low DTC B3157 Passenger Lock Switch Circuit Low DTC B3172 RF Window Up Switch Circuit Low DTC B3177 RF Window Down Switch Circuit Low DTC B3182 LR Window Up Switch Circuit Low DTC B3187 LR Window Down Switch Circuit Low DTC B3192 RR Window Up Switch Circuit Low DTC B3197 RR Window Down Switch Circuit Low DTC B3377 LF Window Up Switch Circuit Low DTC B3382 LF Window Down Switch Circuit Low DTC B3387 RF Window Up Switch Circuit Low DTC B3392 RF Window Down Switch Circuit Low DTC B3397 LR Window Up Switch Circuit Low DTC B3452 LR Window Down Switch Circuit Low DTC B3457 RR Window Up Switch Circuit Low DTC B3462 RR Window Down Switch Circuit Low DTC B3467 LF Window Express Down Circuit Low DTC B3472 RF Window Express Down Circuit Low DTC B3527 Window Lockout Switch Circuit Low
DTC'S are intended to point the qualified technician in the correct diagnostic path. You may have a communication or network problem . Are you familiar with class two serial data bus communication network . The simple bus provides a means for information exchange among the vehicle door modules. Door module information on inputs and commanded outputs are converted to serial bus interface data for exchange among the door modules. The DDM can also take information from modules connected to the class 2 serial data circuit and relay the command to the simple bus interface. The vehicle power mode message (ignition switch position) from the DIM is an example. The DDM periodically addresses each module on the simple bus interface. When a module does not respond to the DDM, the DTC for that module is set. You can't just replace these modules , some need to be programmed . Dealer only ! First check codes , power an grounds etc....

Jun 29, 2016 | 2000 Buick LeSabre Custom

1 Answer

I purchased and installed a new switch master for my 2005 Nissan Pathfinder. Once installed I put the drivers window down per the instructions. After that none of the windows worked. The instructions said...


After 7 yrs, things just don't work as they should. Do the passenger windows work at the door switch? Get a new switch and re install with nothing on but the key switch. If the passenger windows work and the alarm works, then it should be OK! The alarm may be the problem!

Oct 07, 2012 | 2005 Nissan Pathfinder

1 Answer

Front driver door has no power, I have checked the fuses but no controls will work


This is a manufactures bulletin


SUBJECT:
Inoperative Right Front Door Switches OVERVIEW:
This bulletin involves replacing the right door interior handle. The loss of ALL functions may occur when attempting to control them from any of the switches located on the right door due to electrostatic discharge through the right door interior handle. The right door interior handle must be replaced to protect the switch module from static electricity. The new handle is more resistant to electrostatic discharge. MODELS:
2004 - 2008 (CS) Pacifica SYMPTOM/CONDITION:
The vehicle operator may experience a permanent loss in ability to actuate ALL of the following functions from the right door switches: ^ Power door locks. ^ Right power mirror. ^ Right power seat adjustments. ^ Right power window control. ^ Right heated mirrors. ^ Memory functions associated with the listed systems on right side (if applicable). ^ Loss of communication with the right door switch module to Scan Tool: DIAGNOSIS:
Perform a "Hard Reset of the right door switch module. This may be accomplished by removing all power (including memory keep alive power) from the right door switch module by unplugging the module power connector. Alternatively, vehicle power may be interrupted by removing the negative battery terminal when the ignition switch is in the OFF position. If after performing the hard reset functions of the right door switches return perform the Repair Procedure.
dak408_79.gif

PARTS REQUIRED:
REPAIR PROCEDURE:
1. Disconnect the negative battery cable. 2. Remove the right door trim paneldak408_80.gif
3. Remove the door tweeter speaker. Refer to the service information in TechCONNECT. Refer to 8 - Electrical > Audio > Speaker > Removal (Fig 1). 4. Remove the power seat switch. Refer to the service information in TechCONNECT. Refer to 8 - Electrical > Power Seats > right Seat Switch > Removal. 5. Replace the right door interior handle, p/n 05170261AA, as described on Mopar Instruction Sheet K6855628 included in the handle kit. 6. Install the power seat switch. 7. Install the door tweeter speaker. 8. Install the right door trim panel. 9. Connect the negative battery cable.

Nov 25, 2010 | 2006 Chrysler Pacifica

1 Answer

Where is the rear window relay located on the 2002 Ford Explorer sport trac. Not the rear door windows but the very back window.


  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.

NOTE: The power rear window motor is not on the multiplex link. Any diagnosis and testing carried out on the power rear window will not involve the GEM module. NOTE: The reinitialization procedure must be carried out when repairs are performed on any part of the power rear window system including when the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.

Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions
---------------------------------------------------------------------------------------------

Nov 16, 2010 | 2001 Ford Explorer Sport Trac

2 Answers

2003 where is the modules for the liftgate in a 2003 lincoln Nav


tascafordparts.com for discount.

The liftgate actuator and remote control are in the liftgate.
The module is in the left rear quarter trim panel.


SECTION 501-03: Body Closures 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Power Liftgate Module Removal and Installation
NOTE: Prior to removal of the power liftgate module, it is necessary to upload module configuration information to a diagnostic tool. This information needs to be downloaded into the new power liftgate module once installed. For additional information, refer to Section 418-01 .
  1. Remove the rear quarter trim panel. For additional information, refer to Section 501-05 .
  1. Remove the power liftgate module.
    1. Disconnect the electrical connectors.
    1. Remove the bolts.
89dd4de.gif
  1. NOTE: Once the new power liftgate module is installed, it is necessary to download the module configuration information from the diagnostic tool into the new power liftgate module. For additional information, refer to Section 418-01 .

-----------------------------------------------------------------------------------------

Principles of Operation
The power liftgate is controlled by the power liftgate module.
The power liftgate module receives inputs from:
  • glass position switch (determines the ajar status of the liftgate glass).
  • forkbolt switch (determines the primary position of the latch).
  • detent switch (determines the secondary position of the latch).
  • home switch (determines the power cinch status).
  • power liftgate control switch (activates the power liftgate from the interior of vehicle).
  • pinch strip switches (determines if an obstacle is detected between the pinch strip and liftgate).
  • instrument cluster module (activates and sets the options for the power liftgate).
  • optical sensor (determines the direction, travel speed and obstacle detection of the liftgate).
  • UBP serial communication link.
The power liftgate module sends outputs to:
  • liftgate motors.
  • power cinching latch system.
  • liftgate chime module.
  • body security module
------------------------------------------------------------------------------------

The liftgate consists of the following components:
  • liftgate window glass latch
  • door lock actuator (power liftgate only)
  • liftgate latch
  • liftgate handle
  • liftgate latch remote control (power liftgate only)
  • liftgate ajar switch
  • chime module (power liftgate only)
  • -------------------------------------------------

Apr 14, 2009 | 2003 Lincoln Navigator

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

Not finding what you are looking for?
1998 Jaguar XK8 Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...