Question about 2006 Ford Five Hundred

1 Answer

How do I access the fuel pump shut-off switch on a 2006 Ford 500?

I know where the switch is located, but how do I get to get? Do I have to remove some trim , moulding or carpet? If so , can you give me instructions on disassembling the necessary parts to access the switch? Thank You

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 120 Answers

Are you asking about the fuel pump reset switch? The one that is under the glove box?
If so, you can just reach up under there from the passenger seat. The button is on the top of the mechanism, so it takes a little stretching to get to it. Good luck

Posted on Jan 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Is there a reset button on a GMC Savannah 1500 van and where is fuel pump location?


There is no reset button if you mean like a fuel shut-off switch or fuel inertia switch. Only used by Ford as far as I know. I've never heard of one on a GM product.
The fuel pumps have been located in the gas tank since the beginning of fuel injection systems back in the 1980's. Some GM cars since about 2000 have a special access plate in the trunk area just above the gas tank, for fuel pump module removal. Previously, the only way to replace a fuel pump was to remove the tank from the vehicle. That is probably the case in your van, but check for an access plate in the floor, just above the fuel tank-just above the small opening in the tank where the pump is removed.

Apr 30, 2017 | GMC Cars & Trucks

1 Answer

When I turn the ignition off the average fuel reading returns to zero,all other readings,tripometer,miles to empty remain.


2006 Ford Fusion Owners Manual - Scribd

https://www.scribd.com/doc/.../2006-Ford-Fusion-Owners-Manual
Mar 10, 2014 - 2006 Ford Fusion Owners Manual - Ebook download as PDF File (.pdf), Text ... To reset the switch, refer to the Fuel pump shut-off switch in the .... Holding the TRIP/RESET button for two seconds or more will reset the trip odometer to zero. .....Turn the ignition switch to RUN and then back to LOCK. rotate the ...

[PDF]Ford Fusion - Dealer e-Process

cdn.dealereprocess.com/cdn/servicemanuals/ford/2006-fusion.pdf
2006 Fusion (fsn) ... well acquainted with your vehicle by reading this handbook. ...Fuel pump shut-off switch: In the event of an accident the ..... reset the trip odometer tozero. ..... Turn the ignition switch to RUN and then back to LOCK. 4.

Nov 24, 2015 | 2006 Ford Fusion

1 Answer

Removal of rear door exterior lower moulding


the FSM covers this.,
a $4 look
https://suzukipitstopplus.com/Products/10218-2000-vitara-grand-vitara-service-manual.aspx

ill open mine now.
i have no idea at all where hands are touching/? photos?
is this body trim or door trim.
chapter 9 covers this. in the book.
but ive no idea what exact part you are touching.
are is this the seals, or plastic part?
post a photo with finger pointing....

Dec 07, 2014 | 2000 Suzuki Grand Vitara

1 Answer

How do I remove the carpet in a 2001 ford windstar mimivan?


Remove the seats and trim on floor then remove the carpet. Also check the illuminated visors the wire that goes through them shorts out all the time. Just unplug them and see if the fuse still blows.

Jul 03, 2014 | 2001 Ford Windstar

1 Answer

Where is the fuel pump located on the 2006 ford five hundred?


Pump is in the gas tank, and there is no access panel that I know of.

Sep 25, 2012 | 2006 Ford Five Hundred

3 Answers

2006 Ford Expedition blowing Fuel Pump Relay fuse


Try resetting fuel pump. I do believe the reset button is on the forward passengers side of vehicle. The button is behind the plastic shield. Reset once or twice. This hopefully will fix your problem. Look in your manual for exact placement of fuel pump reset button

Mar 25, 2012 | 2006 Ford Expedition XLT

1 Answer

How to replace heat blower


NOTE: The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed from the vehicle without having to remove the HVAC housing.

  1. Disconnect and isolate the negative battery cable.
  2. Remove the passenger side cowl trim panel. See: Body and Frame\Interior Moulding / Trim\Trim Panel\Service and Repair\Cowl Trim
  3. Pull back the carpet to access the front upper screw that secures the air inlet housing.
  4. Remove the recirculation door actuator.
  5. Remove the recirculation door actuator wire lead from the routing clip located on the lower air inlet housing and position the wire lead aside.
  6. Disconnect the blower motor wire lead connector from the blower motor resistor or power module, depending on application.

118348823 Lower Air Inlet Housing

  1. Remove the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing.
  2. Remove the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and remove the lower HVAC housing.

118348824 Blower Motor Wire Lead Grommet

  1. Push the rubber blower motor wire lead grommet through the opening in the lower air inlet housing.
  2. Feed the blower motor wire lead through the opening in the lower air inlet housing and remove the lower air inlet housing from the vehicle.
  3. Position the recirculation-air door as necessary to access and remove the three screws that secure the blower motor to the lower half of the HVAC housing.
  4. Gently flex the recirculation air door far down enough to remove the blower motor and wheel from the HVAC housing.

118348825 Blower Motor Mounting Tabs

  1. Remove the blower motor and wheel from the HVAC housing. Note the position of the blower motor mounting tabs.
INSTALLATION

11_29_2011_3_24_05_pm.gif11_29_2011_3_24_22_pm.gif11_29_2011_3_24_35_pm.gif

Nov 28, 2011 | Chrysler Sebring Cars & Trucks

1 Answer

Hi guys, my 2009 Dodge Grand Caravan get a code C2204 ( Dynamic Internal Sensor) and I want to change the sensor, Can any one tell where is it located? Any help is appriciated. Thank u


REMOVAL

  1. Disconnect and isolate the battery negative cable from its battery post.
  2. Remove the instrument panel center stack console. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Bin - Removal

asetech74.jpg
  1. Roll back the front floor carpet from under the instrument panel toward the rear of the vehicle for access to components. See: Body and Frame\Interior Moulding / Trim\Carpet\Service and Repair\Carpet - Removal
  2. Remove the fasteners (2), then instrument panel center support brackets (2). There is one bracket on each side of tunnel structure.

asetech74_0.jpg 5. Disengage the right intermediate floor distribution duct (2) from the stud located on the floor support (3) and move it aside as necessary to access the dynamics sensor.


asetech74_1.jpg
  1. Disconnect the wiring harness connector (3) at the dynamics sensor (2).
  2. Remove the screws (1) mounting the dynamics sensor to the mounting bracket on the floor pan tunnel (4).
  3. Remove the dynamics sensor (2).

asetech74_2.jpg
Hope this helps....

Sep 16, 2011 | Dodge Grand Caravan Cars & Trucks

2 Answers

I have a 2006 ford f350 and the fuel pump isnt working is there a shutoff switch


Yes. The switch is usually located around the passengers kickpanel. There should be an access hole to press the button on the switch. Sometimes the part is just above the carpet and sometimes you have to remove the kickpanel. If you are unable to find this switch on the passengers side,then look on the drivers side kickpanel.

Under the hood is a Powerbox. The shutoff switch (inertia switch) gets its power from the Fuel pump Relay after the Ignition is turned on. If resetting the shutoff switch does not help, your fuel pump Relay may be bad. On some Ford models, the horn Relay is the same Relay used for the fuel pump. This would allow you to swap and test before buying a new Relay.

Jul 13, 2011 | 2006 Ford F 350 Super Duty

Not finding what you are looking for?
2006 Ford Five Hundred Logo

914 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...