Question about 1995 Geo Metro

2 Answers

Geo metro 94 lock cylinder removal

Couldyou please tell me how to remove the geo metro 94 lock cylinder.
Ilost both my 2 keys. Any body know how to get a new set of keys from car delers given them the vin number.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 97 Geo metro with a broken key inside the ignition. I have removed the column cover and have access to it but don't know how to remove the switch

Posted on Jan 27, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I found the keys

thanks you
Manuneethy

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removed all screws from my geo metro radio.cant find anything holding it.won't come out


Hi,

Normally there is another screw or connections towards the back. Under the steering wheel, remove the panel near the stereo. Also, remove the panel on the right side as well. This will give you access to the rear of the stereo and you will see another screw.

Jul 29, 2016 | Geo Cars & Trucks

2 Answers

Lost my keys to my 1991 geo metro is there any way to have keys made for that ignition


A locksmith can come out and make a key for it. But they used to charge $75 just to come out

Feb 22, 2015 | 1991 Geo Metro

1 Answer

Removing geo lock cylinder


from what,. name it.
point with finger and say.. xxxxxxxxxxxxxxxxxx here.

Apr 17, 2014 | 1994 Geo Metro

1 Answer

How do i chage the fuel injector for a geo metro 1997 LSI?


REMOVAL & INSTALLATION Fig. 1: Removing injectors from fuel rail 84245032.gif
Fig. 2: Make sure injectors rotate freely in cylinder head 84245033.gif
  1. Relieve fuel system pressure and disconnect the negative battery cable.
  2. Remove intake air hose between throttle body and intercooler.
  3. Remove accelerator cable.
  4. Unclamp PCV and fuel return hoses from deliver pipe.
  5. Unclamp injector wiring harness.
  6. Disconnect injector coupler.
  7. Remove cold start injector pipe from delivery pipe.
  8. Remove vacuum hose from pressure regulator.
  9. Remove fuel feed hose from delivery pipe.
  10. Remove pressure regulator from delivery pipe.
  11. Remove delivery pipe with injectors.
  12. Remove injectors from delivery pipe. To install:
  13. Replace injector O-rings and lubricate with fuel. NOTE: Make sure injectors rotate smoothly. If not, probable cause is incorrect installation of O-ring.
  14. Check if insulator is scored or damaged. If it is, replace with new one.
  15. Connect delivery pipe with injectors.
  16. Install pressure regulator to delivery pipe using a new O-ring.
  17. Install fuel feed hose to delivery pipe.
  18. Install vacuum and fuel return hoses to pressure regulator and clamp securely.
  19. Install cold start injector pipe to delivery pipe using new gaskets.
  20. Install injector coupler. Clamp injector wiring harness.
  21. Install PCV hose to cylinder head.
  22. Install throttle position sensor coupler.
  23. Install accelerator cable and adjust free-play.
  24. Install intake air hose to throttle body and intercooler.
  25. Connect the negative battery cable.
  26. Start engine and check for leaks.
prev.gif next.gif

Jul 03, 2010 | 1997 Geo Metro

2 Answers

My 94 geo metro runs very rough and has


you should check a throttle body valve or purge valve, choke valve

Feb 14, 2010 | 1994 Geo Metro

2 Answers

What should i set the timing at for my 94 geo metro i have a timing light should i set it at 0?


Unless you have replaced the hood or the sticker has been removed, there should be a label on the inside of your hood that lists the correct timing.

Make sure you short the two appropriate wires in the 'test plug' before setting the timing. It's on the drivers side firewall under the hood. The idle on 94 Metros is automatically controlled so you don't have to worry about setting the idle before adjusting the timing. My 94 automatic metro says 5BTC.

May 18, 2009 | 1994 Geo Metro

1 Answer

1993 GEO METRO


remove steer wheel with puller. u will see black cover remove 3 tork screws.remove. next u will need a special tool push down on plate . remove clip in center. remove plate. lift turn arm . remove bolt for lock cly. turn key lock will slide out

Nov 29, 2008 | 1993 Geo Metro

2 Answers

93 Geo Metro


As long as they are the same type of engine ( I believe they should both be 1.0L 3 cyl engines). Most parts for the Geo Metro from 1992 to 1994 interchange with out a problem.

Nov 10, 2008 | 1993 Geo Metro

1 Answer

1994 Geo Metro manufacture date


Most cars that I've seen have a decal in the driver's door jamb, either on the door or the car's body, which shows a month and year of manufacture. If not there, check the passenger side jamb. If neither side has the decal, you can call the dealership and ask them to tell you the build date by looking it up using your VIN number.

Aug 10, 2008 | 1994 Geo Metro

Not finding what you are looking for?
1995 Geo Metro Logo

438 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...