Question about 2000 Chevrolet Monte Carlo

1 Answer

Turn signals my turn signals aren't working at all. All the bulbs and fuses are good. what do i check next?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 185 Answers

Check the thermal flasher. It is a little metal can about the size of a quarter located (usually) in the interior fuse panel. This panel usually located in the dash just to the left of where the drivers knee would be. You can get a replacement at any auto parts store.

Hope this helps Loringh PS Please leave a rating if appropriate Thanks

Posted on Nov 17, 2008

6 Suggested Answers

  • 1 Answer

SOURCE: No rear brake light / turn signals on 2001 Chevy Cavalier

The problem is the turn signal/headlight/hazard switch assembly on the steering column which the brake light wiring runs through. The part is easy to change and cost about $50 at most parts stores

Posted on Sep 05, 2008

  • 1 Answer

SOURCE: Turn Signals not working

The blinker button (hazard lights 4 way blinking) which is also a relay, is broken. with time the tention on the metal contacts gets loose so the contact only happens sometimes. pop it out with a thin screwdriver and replace it, 15$ on ebay...

Posted on Oct 12, 2008

localwonder
  • 6784 Answers

SOURCE: 2000 toyota camry turn signals not working. Fuses

Hi, i recommend testing the switch and flasher module. i will post the testing procedures for both devices. replace the device that is faulty.

To test turn signal switches, use a 12-volt test light to probe for voltage into and out of the switch. The ignition switch must be in the RUN position for the circuit to operate. If voltage is present on the input side of the switch but not on the output side, the switch is faulty.

FLASHER TEST PROCEDURE---

  • A test light can be used to determine which flasher is used for the turn signals and which is used for the hazard warning light.
  • An easier way is to turn on both the directionals and the hazards. This activates both flasher units.
  • By removing one of the flashers, the affected circuit no longer flashes.
  • Therefore, that flash unit controls that particular circuit.
  • If the turn signals fail to operate and the fuse is good, the flasher has probably failed.
  • Occasionally, the flasher does not flash as fast as it once did, or it flashes faster. This is also cause for replacement.
  • If it flashes too slowly or not at all, check for a burned-out bulb first.
the flasher is located in the Front seating area, driver side, driver side of steering column, mounted in corner behind instrument panel

If the turn signals operate properly in one direction but do not flash in the other, the problem is not in the flasher unit. A burned-out lamp filament will not cause enough current to flow to heat the bimetallic strip sufficiently to cause it to open. Thus the lights do not flash. Locate the faulty bulb and replace it.

Posted on May 19, 2009

  • 4 Answers

SOURCE: 1997 Chevy Tahoe both turn signals stopped working

Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Posted on Jul 21, 2009

  • 4 Answers

SOURCE: 99 Chevy Tahoe... Rear turn signals, brake lights, and hazards

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Posted on Oct 11, 2009

  • 1 Answer

SOURCE: Turn signals and 4-way flashers do not work - 1997 Buick Century

turn signals some times don't work

Posted on May 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal problem.Fixed all bulbs and made sure flasher relay was working.all running lights brake lights reverse lights work and hazards work.but I get nothing on dash or lights when trying.


Double and triple check the fuse for your rurn signals both visually and with ammeter to check for fuse continuity, or just replace with new one of same amperage. The fuse can look good but have a hairline crack that is not visible.

Oct 19, 2015 | Cars & Trucks

2 Answers

Front light next to the headlight does not work. All other lights work fine except the rear right turn signal blinks fast.


Depending on the make model and year, I would say you are talking about the front turn signal lamp. Thats why the signal flashes fast.
I would check the socket for power and ground next.

Dec 05, 2014 | Cars & Trucks

2 Answers

Brakelightswontwork1996jeepgrandcherokee


First, check the fuses and the bulbs. Also check for voltage at the light bulb socket. IF no voltage, and bulbs and fuses are good, next thing to check is the brake light switch.

Nov 13, 2014 | Cars & Trucks

1 Answer

Rear Turn signal is not working


Aren't your brake lights and turn signal lights on the same bulb, same filament? Recheck the bulb in the rear, as the rapid blinking is an indication of a burnt out bulb. If the bulb is the correct one and is good, check the connector and socket at the housing for a loose or poor connection.

May 26, 2012 | Dodge Durango Cars & Trucks

1 Answer

95 grand marquis no turn signals changed the switch still didnt work changed the lcm no change all the fuses are good . next problem have no climate control nothing lights up fuses are good thank you


check the turn signal flasher,also check the bulbs some autos,are designed to do this.
If there is a blown bulb,the turn signal on that side will not blink,but will burn steady to tell the driver,a short in wiring can also cause this

Sep 25, 2011 | 1998 Mercury Grand Marquis

3 Answers

Both my right & left turn signals aren't working but hazards are


If you can locate the hazrd flasher unit under the dash on the drivers side, the turn flasher unit should be right beside it and looks the same. Unplug and switch the 2 flashers and see if the turn signals work. The flasher unit is a silver and round. they are usually close to the stering colum. Let me know if that helps.

Mar 27, 2011 | Dodge Durango Cars & Trucks

1 Answer

Turn signals not working in a 1993 Jeep Grand Cherokee


fuses good? turn signals come on but won't blink? check blinker switch under dash at fuse panel, it will be a round push incylider next to fuse panel, with signals on put your finger on round cylinder, if you don't feel it click, it's bad.also if not that check for a blown bulb in turn signals. hope this helps!!

Nov 11, 2010 | Jeep Grand Cherokee Cars & Trucks

3 Answers

Blower motor and turn signals stopped working


CHECK BLOWER MOTOR FUSE AND RELAY.IF ALL IS GOOD.CHECK TO SEE IF BLOWER IS GETTING POWER.IF NOT.SWITCH IS BAD.IF YES REPLACE BLOWER MOTOR.IF TURN SIGNALS STOP WORKING.CHECK FUSE FIRST.IF FUSE LOOK GOOD. CHECK BULBS TO SEE IF THEY ARE BLOWN.IF BULBS LOOK GOOD PROBLEM COULD BE WORN OR CORRODED BULB SOCKETS OR.BAD GROUND.OR THE TURN SIGNAL SWITCH IS BAD.

Aug 24, 2009 | Plymouth Voyager Cars & Trucks

Not finding what you are looking for?
2000 Chevrolet Monte Carlo Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...