Question about 2001 Audi A4

1 Answer

Gear 1 and reverse gear can no longer be engaged in my Audi A4 2002 1.8T Manual. On gear 3, the gear lever is very loose as though in neutral position, any help out there?

Posted by on

  • karuperse666 May 11, 2010

    where this gear link is loacated?

  • Anonymous Mar 27, 2014

    this is it ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Thanks I got the solution it was fixed this morning. One of the gear links was loose and out of place just at the gearbox level

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gears seem to want to slip out and make a winning noise in certain gears too is my gearbox done for or is it more likely clutch it's Audi a3 with 130000 on the clock and clutch is very high too any...


gears slipping out will be indicated by the gear lever jumping into neutral.This can be from incorrect rear engagement from a loose worn pivot in the gear lever tower or something stopping the gear lever from moving properly.. Clutch problems are indicated by --going to the floor. crashing 1st gear, engines rpm s climbing without an appreciable vehicle speed increase. If there is a fault in the gear box it will be only in the gear engaged (missing teeth-chipped ) and not all gears. If it is a bearing then there will be no noise in 4th gear
Boxes are repairable as mostly it only needs that faulty part to be replaced

Dec 22, 2014 | Audi A3 Cars & Trucks

1 Answer

2000 ford focus, manual, the stick stick flops around not engaged


There are three posibilities for this worn linkage on the gearbox the linkage under gear lever or a broken mounting on the bracket where the lever comes up through the floor as long as you can get all gears it will be exturnal linkage fault.

Mar 04, 2014 | 2000 Ford Focus

1 Answer

1995 celica 2.2L doesn't engage gear 2,4,r


are you saying this car is a A/T car, AUTO and not a stick?

say so, as both have 2,4 and reverse gears.

i think its a 5speed manual.

so the tip of the shifter is bad, remove it see plastic parts bad.

you could shift car , by moving the transmission levers and id bet it does work so that leaves. bad shift lever parts.

i bet the lever is real loose , so loose the H pattern is garbage
right> ?

Feb 01, 2014 | 1995 Toyota Celica

2 Answers

Audi a3 auto reverse gear doesn't move


run fault codes and look for faulty TCM and reverse servo .

Nov 29, 2013 | Audi Cars & Trucks

1 Answer

Gear lever loose & wont engage in 06 renault magane manual


Sounds to me that your cable is broke therefor not putting the car in gear. This can happen real easy. Have someone move the shifter for you and look at the side of your trans and see it the cable is moving. If not then you can do a visible inspection of it and see if it is broke.

Nov 25, 2012 | Cars & Trucks

2 Answers

Cannot get 5th and reverse gear. Feels like neutral. 1, 2, 3 and 4 work fine.


the linkage is loose or poping out! check to c if trans is tightend down

Aug 22, 2012 | 1995 Dodge Neon

1 Answer

Reverse on my gmc envoy not working


This can be due to few reasons but the most important can be as follows:

1. If can be a mis-alignment of the gear lever to the gear box as normally the reverse gear is always engage with more movement . so a change of postion or setting can alter the notch settings and refuse to engage properly.
2. Secondly the fault within the gear box, if there is a linkage or counter wheel/gear setting within it will not mesh or engage as the setting would be altered.
3. finally gaps or bush failures in the gear lever, linkages or the gear box will make the movement restricted and hence not engage.
You need to check on all the above. Thank You.

Sep 24, 2011 | GMC Envoy Cars & Trucks

1 Answer

Hi, I own a 1997 Ford E 350 Econoline, I have the following transmission engagement problem: Truck will not start: Transmission will not engage any gear, neutral or park. The shift lever feels like is not...


The weld on the manual lever is known to break loose. First, with the wheels off the ground, with the lever in the park position, does the drive shaft lock in park? If yes or no sometimes, drop the trans pan. I bet the nut on the lever camd loose.

Mar 31, 2010 | 1994 Ford Econoline

1 Answer

Car wont roll forward or back even in neutral


I assume it's a manual transmission.
If the car will not roll backward or forward in neutral (with or without the clutch engaged) the transmission is most likely locked in two gears at the same time.
This may happen if gear selectors are excessively worn. If you are able to examine the gear selection levers external to the gearbox, ensure they are in the 'neutral' (no gear selected) position when the gear lever is in Neutral. If not in correct position, you may be able to manually reset the levers to correct neutral position and thereby unlock the gearbox.
In any case, if it's happened once, it will happen again, so get the gearbox and gear selection mechanism checked for wear or breakage.


Jul 31, 2009 | 1997 Subaru Legacy

1 Answer

Shifter physically won't move into reverse position


To isolate the problem as either an internal transmission problem,or external to the transmission,(shifter or cable malfunction),the shifter cables should be disconnected from the transmission.On the transmission are two levers,if you have a 5 speed trans.One is the neutral gate lever,and the other is actual gear shift lever.Manipulating the levers manually,see if the transmission will engage into Reverse gear.If the transmission engages into Reverse gear,then the problem is either in the shifter mechanism itself,or the shift cables.If the transmission will not engage into Reverse gear,then the problem is either an internal problem,or possibly a switch seized up,like the reverse gear indicator switch.At this point,i would have an assistant sit in the car,engine off,and run through all the gear selections with the shifter,while watching and looking for a cable not operating to its full stroke.Take the console apart to access the shifter mechanism and visually inspect the assembly.Disconnect the cables and operate them manually,one at a time,while an assistant watches them underhood.Visually inspect the shifter and it's mechanism for a broken,cracked,or damaged component.At this point,the problem should be identified and repaired as either cable or shifter malfunction.

Nov 25, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
2001 Audi A4 Logo

Related Topics:

897 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13152 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...