Question about 2000 Nissan Xterra

1 Answer

I need to know how to replace the starter

4wd. Were is the starter located and what tools do I need?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 81,342 Answers

You will need to jack the truck up in the air and put it on stands and then disconnect the battery neg cable, the starter is at the rear of the engine, it is hjeld in by 2 14mm bolts and then the wiring.

Posted on Apr 26, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it hard to replace the starter on the 5.4 engine with 4wd? Can I do it in my garage with regular tools?


You should be able to do it in no more than a couple of hours in your garage with basic hand tools. The link below will take you to detailed instructions on how to replace the starter.

Starter Replacement Instructions

Please rate my response.

Jan 15, 2011 | 1998 Ford Expedition

1 Answer

I need to replace the starter on my 1998 Dodge Ram 1500 4wd 5.9l


Easy fix my friend.

1. Unhook the battery
2. Raise and support the truck on jack stands.
3. The starter is located on the drivers side at the front of the tranny.
4. Grab an 8mm and a 13mm wrench.
5. Remove the power wires from the starter.
6. Remove the starter by removing the top bolt 9/16 i believe and the bottom nut. Also 9/16 or 5/8.
7. Carefully slide it out toward the front of the engine.
8. Installation is the same as removal.

Hope this helps.

May 09, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

I am replacing a starter on a 96 s10 4wd and I


Right side. For any car, just follow the large positive battery cable, it always ends at the starter.

Dec 19, 2009 | 1996 Chevrolet S-10 Pickup

1 Answer

My 1999 toyota corolla having 120K plus mileage is probably going to need a new starter soon. Does anybody know how to replace the starter? What tools do I need? Thanks.


Between the engine and transmission is the location of the starter, on the outside of them. Basic tools to remove the bolts holding it and the electrical connectors need to be disconnected. Purchase a repair manual for details as this is a decent job.

xxsodasipperxx@yahoo.com

Dec 09, 2009 | 1999 Toyota Corolla

1 Answer

Replacing 4WD actuator


It is located by the front pumpkin should be 4 bolts I believe that hold it in and 1 connector

May 27, 2009 | 1998 Chevrolet K1500

1 Answer

Where is the starter located and what tool are required to remove


you have to look with a flash light depending on the vehicle, go under the vehicle and look left to the right of the bottom of the engine and you should see a elongated part no bigger than 12 inches(smaller) and it will have no more than three wires with a smaller cylinder attacked to it. most of the time there will be 3 bolts or nuts holding it on. tools= socket set; standard for domestic vehicles and metric for import vehicles, open end wrenches and wire cutters(just in case). most of the time on domestic cars you will use a size of 1/2 to 9/16 for you tools. start with disconnecting the battery then remove the starter. when putting the new one on just turn the teeth on the starter to line up with the wheel in the engine, you will see that when you remove the old starter. splice the new power wire if needed for the power, a new wire should come with the new starter if it is needed. hook the battery back up and enjoy!

Jan 12, 2009 | 2000 Dodge Caravan

1 Answer

Starter replacement - 1991 Toyota previa


Here are detailed, step-by-step instructions for the removal and re-installation of your starter motor. Hope this helps! Have a great day!

Starter Toyota Previa 1991-1997 Repair InformationREMOVAL & INSTALLATION
See Figures 5 through 12
  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front driveshaft.
  4. Remove the nut and disconnect the starter wire.
0900c15280089fbb.jpgFig. 5: Disengage the starter wiring
  1. Disconnect the starter connector.
0900c15280089fbc.jpgFig. 6: Remove the cap hiding the nut 0900c15280089fbd.jpgFig. 7: It will be necessary to use an extension to remove the nut
  1. Remove the bolt holding the starter stay to the upper stiffener plate.
  2. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  3. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
0900c15280089fbe.jpgFig. 8: Four bolts hold the starter in place 0900c15280089fbf.jpgFig. 9: The nut is located on the top of the starter 0900c15280089fc0.jpgFig. 10: Extract the starter from the engineTo install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc1.jpgFig. 11: Bolt locations on the 2WD models
  1. If equipped with 2WD, install the starter, nut and three bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc2.jpgFig. 12: Bolt locations on the 4WD models
  1. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  2. Install the starter connector.
  3. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  4. If equipped with 4WD, install the front driveshaft.
  5. Connect the negative battery cable.
SOLENOID REPLACEMENT
The starter solenoid (magnetic switch) is an integral part of the starter assembly.
  1. Remove the starter from the van. Remove the heat insulator from the starter assembly, if equipped.
  2. Disconnect the wire lead from the magnetic switch terminal.
  3. Remove the two long, through bolts holding the field frame to the magnetic switch. Pull out the field frame with the armature from the magnetic switch.
  4. Toseparate the starter housing from the magnetic switch assembly, remove the two screws and the starter housing with the pinion gear (1.6 kW), idler and clutch assembly.
To install:
  1. If necessary, install the gears and clutch assembly to the starter housing. Apply grease to the gear and clutch assemblies and place the clutch assembly, idler gear, bearing and pinion gear (1.6 kW) in the starter housing.
  2. Insert the spring into the clutch shaft hole and place the starter housing onto the magnetic switch. Install the two screws.
  3. Install the field frame with the armature onto the magnetic switch assembly and install the two through bolts. Tighten the bolts on the 1.4 kW to 52 inch lbs. (6 Nm) and on the 1.6 kW to 82 inch lbs. (9 Nm).
There is a protrusion or tab on each part; make sure you line them up correctly during assembly.
  1. Connect the wire to the terminal on the magnetic switch and tighten the nut to 52 inch lbs. (6 Nm). Install the heat insulator, if equipped.
  2. Reinstall the starter on the vehicle. Check starter system for proper operation.

Nov 23, 2008 | 1991 Toyota Previa

Not finding what you are looking for?
2000 Nissan Xterra Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

81294 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...