Question about 2003 Chrysler Concorde

1 Answer

How do I remove the headlight assembly

I need to change the bulbs in my headlight assy. How do I remove the assy. to access the bulbs?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Contributor
  • 29 Answers

Two torx head screws per headlight, once you loosen them you will see they are very long, pull them out and the headlight should pull forward

Posted on Nov 17, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to change headlight assy on 2000 dodge caravan

Remove the screw from the black tab on top of the headlamp assembly. Around the headlamp plug, there are 3 nuts, remove them carefully, as they are easily dropped and lost, remove the ring that secures the bulb to the assembly, it only turns a portion of a turn. Slide the entire headlight assembly partially out the front, then disconnect the rubber plug that contains the marker/turn signal bulbs. Re assemble in reverse order, making sure the headlight bulb is properly aligned or the ring will not tighten. Also,take care not to touch the headlight bulb glass, as the oil from your fingers may cause the bulb to break when it heats up. Hope this helps.

Feb 26, 2015 | 2000 Dodge Caravan

2 Answers

Changing headlight bulb.

Some car it is hard I did G6 took me one hour.You can get bulb or whole light out.

Apr 25, 2013 | 1993 Chrysler Lebaron

1 Answer

How to change headlight bulb

Depending on how much room you have behind the headlight assembly, unplug the wire connector turn the bulb 1/3 - 1/4 turn counterclockwise and remove. when reinstalling DO NOT TOUCH THE GLASS (it is a halogen bulb) of the bulb when installing, doing so will transfer oils from your skin and cause premature failure. If you do clean the glass with rubbing alcohol and a clean cloth. If there is no room to reach in and remove the bulb, the headlight assy will probably have a couple of screws that when removed will allow you access to the bulb. BTW the part # you need is 9007

Dec 15, 2011 | 2003 Mitsubishi Lancer

2 Answers

Trying to change headlamp

You need to remove the clips that hold on the grill, so you can pull away the grill as far as you can. You'll need to partly remove the headlight assembly to get to the bulb. Small hands are a plus!!!!

Mar 15, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Which bolt holds the headlight assy in i need to change the low beam bulb

There is a 10mm bolt that bolts into a cross plate. Unscrew that and raise the plate an inch or so; then jimmy the headlight assembly loose enough to gain access to the wiring harnesses. To remove, pull the inside corner of the assembly first and then slide out.

Jan 17, 2010 | 2005 Pontiac Grand Prix

2 Answers

How do I change the low beam bulb(drivers side) on 2005 Pontiac Grand Prix?

Upside down L shaped bracket that is bolted to frame just behind headlight assy. Unbolt bracket, lift bracket straight up to unlock headlight assy. Headlight assy should easlier fall forward to replace any of the 3 bulbs

Sep 26, 2009 | 2005 Pontiac Grand Prix

1 Answer

Replacing 2001 Hyundai XG300 headlight, how difficult?

1bd6158.jpg Here's a photo - remove cap, disconnect connector to bulb, move bulb retainer out of the way & extract bulb - installation of new bulb is in reverse order.
If you want to replace the entire ASSEMBLY, there are three (3) 10mm bolts holding the assy. Remove them, then slide assy forward to access connectors - disconnect them.


Jun 20, 2009 | 2001 Hyundai XG300

1 Answer

Bulb replacement 2004 expedition

which bulb are you trying to change? the headlight assemblies are removed by pulling up on the two tabs that are located under the hood just behind the headlight. The turn signal lamp is attached to the headlight assembly with a screw.

Mar 20, 2009 | 2000 Ford Expedition

2 Answers

How do you change the right front headlight bulb on a kia sedona

Remove the headlight assembly. Just remove the 3 bolts with a 10 mm socket and pull it out so you can disconect the wire harness. After that pull the whole assembly out and unscrew the bulb cover. The bulb is held in with a spring clip.

Dec 25, 2008 | 2003 Kia Sedona

Not finding what you are looking for?
2003 Chrysler Concorde Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides