Question about 2007 Chevrolet Equinox LS New Cars

1 Answer

2007 chevy equinox turn signals, hazard lights, lift gate stopped

While parked in a parking lot for 5 minutes something strange happened elctronically to vehicle. when i got in car and started driving (rain, puddles, highway) all of a sudden the turn signals didnt work...inside or ouside. the lift gate doesnt open (no electronic 'click' when i open with remote), windshield wipers have only 1 speed now, instead of 3. inside electronic door locks do not work.

Posted by on

  • 1 more comment 
  • pamon1214 Jan 25, 2009

    I have the same problem. It started on a very wet rainy and cold day as well, and has continued through very cold weather

  • Diane
    Diane Mar 15, 2014

    i have the same problem. what is the solution to 2007 equinox

  • Carol Bryan
    Carol Bryan Jun 29, 2014

    pop and it went off. Also, the turn signal noise didn't work. The next day my battery was dead. But that was original . Now almost 2 months later, my radio and turn signals are doing the same thing. Oh, and my winshield washer doesn't work.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have the same problem with my 2007 chevy equinox. how can i fix it?

Posted on Aug 10, 2013

6 Suggested Answers

  • 117 Answers

SOURCE: 2007 Chevy Equinox - with

believe it or not you need to take it to the dealer. There is a software reprogram for the remote control door lock receiver to fix the probelm - really common on tahoes and suburbans. Go to the dealer and tell them about bulletin #06-08-52-002g. It probably will need new remotes also. Try and get the dealer to warranty it since its a known product defect and a known problem

Posted on May 03, 2009

wickedsteele
  • 56 Answers

SOURCE: windshield wipers

You will need to replace the wiper motor. Most likely the circuit board is bad. You might check with your local chevy dealer and see if there is a recall on the wiper motor before you buy a new one, even if you are not the original owner the car the recall will still be done free of charge. Some chevy models did have a wiper recall. I hope this helps.

Posted on Aug 09, 2008

  • 1 Answer

SOURCE: Windshield wipers not parking

The problem could be a bent parking pall bracket. This is usually caused when you wipe snow from windshield using the wipers instead of brushing off. You need to remove both wipers and the cover from the drivers side. Remove the cover over the wiper motor assembly (held by a plastic button). On the right side of the wiper mechanism is a small tab (part of the wiper bracket). This tab needs to be straight for the wiper park pall to rest against.Carefully hammer this tab straight (or you may have to replace bracket, big job) Then cycle the wiper and you will see the assembly return to park position. Re-install all parts in reverse order.
Hope this works for you.

Posted on Feb 28, 2009

  • 4 Answers

SOURCE: 99 Chevy Tahoe... Rear turn signals, brake lights, and hazards

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Posted on Oct 11, 2009

  • 1 Answer

SOURCE: On my 2007 Chevy Equinox

i have chevy equinox 2007 LT with AWD system, my problem is that i have two messages appearing in the DIC : satbilitrack and service tracktion control. can u help me with this and tell me whats the problem and how should i fix it?

Posted on Apr 13, 2011

  • 1 Answer

SOURCE: How do I replace the rear windshield wiper motor

How to remove rear wiped from a 07 equinox

Posted on Aug 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How did someone so easily steal my entire turn signal LAMP assembly from walmart parking lot? Sorry, I originally described it wrong. It was below the headlights outside the car, not inside


Hi Raymond:
What a strange thing to have happened.
I'm assuming that it was installed in the vehicle, so the thief would have had to:
1) Get access into the vehicle (hopefully the doors were locked)
2) Open the hood (latch release mechanism is inside the vehicle)
3) Disconnect the battery. (stops the horn from blowing)
4) Remove the steering wheel
5) Remove the turn signal assembly.
Sounds like a LOT of work to steal the part.
Very strange.

May 11, 2016 | 2006 Chevrolet Tahoe 5.3

1 Answer

Where is the blinker relay in my 2011 Chevy Equinox.


PCB Relays
This vehicle is equipped with the following printed circuit board PCB mounted relays.
• High beam
• Low beam
• DRL
• Fog lamp
• Park lamp
• Stop lamp
• Horn relay
They are directly soldered to the underhood fuseblock circuit board. A failure of one of these relays will require the whole under hood fuse block to be replaced.

Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.

Vehicles are just not the same as they use to be. Electronics !!!!!

Sep 25, 2015 | 2011 Chevrolet Equinox

2 Answers

2005 Chevy Equinox passenger side tailight doesn't work. Brake light, turn signal, and hazard work but unit does not illuminate at night. Easy fix ?


Have you tried swapping the bulb from the other side see if that works If not check for power and ground at the tail lamp circuit that is inoperative. Also take a good look at the connector(s) make sure there is no corrosion in the terminals.

May 19, 2014 | Cars & Trucks

1 Answer

1991 Park avenue, Tail lights and license's plate light's stopped working turn signal's hazards and brake lights still functional. but no tail lights or license plate lights


Check for Power on your License Plate Light, more than likely you have lost GROUND

Turn Signals, Do the Front Work and the Back don't? If NONE then FLASHER FUSE

Apr 09, 2013 | 1991 Buick Park Avenue

1 Answer

None of the blinkers work on my 1996 dodge stratus, all bulbs are good as the park lights and flashers work. I have three dead ports in fusebox under hood.


Guessed it's a V6. Trying to sort this out. If setting the headlamp switch to PARK turns on the park filaments of the front park/turn signal lamp and the tail filaments of the rear tail/stop lamps and the separate tail lamps, the park light circuit is good. If 20A fuse 6 in the power distribution center is OK, the combination flasher in the multifunction switch is receiving power. Power is directed to the turn signal lamps by operation of the turn signal/hazard warning switch. If the turn signals are not flashing, the combination switch may have failed or the turn signal flasher part of the combination flasher may have failed. Finally, the hazard warning switch causes the turn signal elements of the front combination park/turn signal lamps and the rear turn lamps to flash.

Sep 14, 2012 | 1996 Dodge Stratus

2 Answers

When in park hard to move shift stick out of park


Moving the shifter out of park is sometime diffucult if the vehicle is parked on an incline or decline?

Aug 15, 2010 | 1993 Honda Accord

1 Answer

Honda transmission stuck in park


In all probability the brake sensor on the pedal is starting to work erratically. This sensor sends a signal to the shifter gate, and the gate will not open unless the brake pedal is depressed. I had it happen to me, and the only solution until i replaced the sensor was to hit the brake over and over until the stop light worked. If the stop lights work, the shifter gate should allow the shifter to move out of park. This sensor/ switch is located about 3 inches above the brake pedal, and it is easily recognizable by the cable attached to it.

Jul 07, 2010 | 1998 Honda Accord

1 Answer

85 Chevy k10 pickup: Working headlights, but no park/tail or turn/hazard lights.


one of your bulb is blown one bulb will shut the rest off check all your bulbs.

Jun 03, 2009 | 1985 Chevrolet Chevy

4 Answers

2006 chevy equinox lt can't get the key to turn. so the car won't start, stuck in park all-wheel drive so it won't tow or move out of the parking spot.


Turn the key while turning the wheel, either to left or right. "jiggleitalittleit'llopen" I had the same thing happen to our GMC safari, the steering wheel got locked. The wheel had turned sharply and it was jammed. I fiddled with it turning the wheel back and forth while trying to turn the key, eventually it popped loose. 'WHEW!' Good Luck!

Jul 09, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
2007 Chevrolet Equinox LS New Cars Logo

1,090 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...