Question about 1988 Nissan Pulsar

1 Answer

Do you have to remove trans when you replace the engine

On a 88 nissan pulsar?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

The engine and the transmission is bolted together, it is always better to remove them at the same time, it is easier to seperate the transmission from the engine when they are both out of the vehicle.

Posted on Jan 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan wiring diagrams


musnt laugh here but go to the scrapper and get the right loom

Nov 02, 2013 | Cars & Trucks

1 Answer

Nissan pulsar '88. replaced starter motor, then


Is it a manual, or an automatic? Earlier Nissans sometimes have a problem with the neutral safety switch (a device that keeps the engine from rolling over in gear or without the clutch depressed.) Generally, if their bad, they need to be a little warm before they'll start, like setting in the sunlight for a few hours.

Good Luck!

May 22, 2010 | 1988 Nissan Pulsar

1 Answer

Thermostat for Nissan Pulsar 1992 Model


STANT REVERSE POPPET SERIES THERMOSTAT -- 195%XB0 F, A Direct Fit OE Replacement Engine Coolant Thermostat,
Thank you for using FixYa , Lee

Feb 22, 2010 | 1990 Nissan Pulsar

1 Answer

1988 Nissan Pulsar will not engage clutch. Engine


You need to replace the clutch and pressure plate --your clutch is worn out. Plus other parts like throw-out bearing ,pilot bearing and may even need the flywheel machined flat.
You need to take it to a shop or if you are mechanicaly minded could do it your yourself,

Nov 15, 2009 | 1988 Nissan Pulsar

2 Answers

Alternator


1996 Nissan/Datsun Sentra 1.6L SFI DOHC 4cyl

Nissan Sentra/Pulsar/NX 1982-1996 Repair Guide
The alternators for Pulsar and Sentra have not changed much over the years. However, the 1987-88 alternators for Pulsar and Sentra have a different internal diode assembly.
  1. Disconnect the negative battery terminal.
  2. Disconnect the 2 lead wires and connector from the alternator.
  3. Loosen the drive belt adjusting bolt and remove the belt.
  4. Unscrew the alternator attaching bolts and remove the alternator from the vehicle.
To install:
  1. Install the alternator and retaining bolts loosely.
  2. Install the belt and connect the wiring.
  3. Adjust the belt as outlined in . Torque the retaining bolts to 25 ft. lbs. (34 Nm).

I hope help you with this (rated this help).

Sep 11, 2009 | 1996 Nissan Sentra

1 Answer

My 88 nissan pulsar 1.8 dosnt get spark


make sure the computer has a 5 volt reference signal.

Jun 12, 2009 | 1987 Nissan Pulsar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...