Question about 1994 Isuzu Rodeo

1 Answer

Repair/Replace 1994 Isuzu Rodeo Fuel Line

There is a leak in the fuel line located at the engine compartment. I can see about where the leak is. How do I replace the fuel line or repair the leak.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 303 Answers

Is the line plastic or steel? They make repair kits for plastic lines, if you can find them. They are hard to find. If it is a steel line, you can go to the parts store and buy a pressure fitting. Cut the line and put the pressure fitting on. If it is the end of the lines, where they hook together or hook to fuel filter, it could be bad O-rings. Need more info.

Posted on Nov 19, 2008

  • straycats196 Sep 09, 2012

    I have steel line but also thre is rubber lines, the rubber lines are attached to the stte lines with just clamps

  • rom marrow
    rom marrow Nov 09, 2013

    steel line fom bowl/housing into this unit that is on side of housing,i need the name of that part for my 1996 e350 7.3 deisel

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have to regularly prime air out of fuel system to start


Sounds as if you have either a loose hose to the injection pump or a hole in the supply line allowing air to get in when engine is stopped. Check under vehicle after it sits to make sure you see any puddling of fuel. also inspect the lines going back to the fuel tank to see if you see fuel staining. Check the connections to the fuel tank to make sure they are sealed properly.

Jan 11, 2014 | 1994 Isuzu Rodeo

1 Answer

On my 2001 rodeo the check engine lite came on and the only code that came up is po440, can you tell me what this is


This alarm concerns the function of the EVAP SYSTEM. This system monitors vacuum correctness. If a sufficient vacuum level cannot be achieved, a large leak or a faulty EVAP canister purge solenoid is indicated. It can be caused for the following reasons:
1) Disconnected or faulty fuel tank pressure sensor
2) Missing or faulty fuel cap
3) Disconnected, damaged, pinched, or blocked EVAP purge line.
4) Disconnected or damaged EVAP vent hose.
5) Disconnected, damaged, pinched, or blocked fuel tank vapor line.
6) Disconnected or faulty EVAP canister purge solenoid.
7) Disconnected or faulty EVAP canister vent solenoid.
8) Damaged EVAP canister.
9) Leaking fuel sender O-ring.
10) Leaking fuel tank or fuel filler neck.

Apr 13, 2011 | 2001 Isuzu Rodeo

1 Answer

2000 Isuzu rodeo fuel tank filler neck leaks whenever I fill up with gasoline. Is there someway for me to fix this or do I need to replace it entirely?


Hello, It may be rusted out right under the fuel line so it is my habit NOT to mess with gasoline. I would look into replacing it. If you know how to replace it, I would do it; if you do not know how to, I would get someone to replace the receiving line.
Hope this helps,
Dana

Dec 31, 2010 | Isuzu Rodeo Cars & Trucks

1 Answer

Fuel problem holden rodeo ute 1994 is not starting beleave it could be the fuel pump. Remove line no fuel coming out belreave that the pump is beside fuel tank drivers side of vehicle


In that year of vehicle I wouldn't be surprised if the fuel pump was in the tank. I would be surprised if it was not in the fuel tank.

Jul 05, 2010 | 1994 Isuzu Rodeo

1 Answer

Where is a fuel filter located in a 1994 toyota camry, and what are the steps to replacing it?


1994 Toyota Camry 3.0L EFI DOHC 6cyl
The Fuel Filter is located under hood, driver side, front side of strut tower, mounted on fenderwell in fuel line.

How to Replace a Fuel Filter
(DIY Complexity: Moderate / Time: 1.4 hours)

Parts:
1. Fuel Filter

Tools:
1. 3/8 in. Drive Ratchet
2. Hose Pincher
3. Flare Nut Wrench
4. Flat Head Screwdriver
5. Socket Set

Steps:
Step 1 Open the hood and locate the fuel filter. If the fuel filter is not in the engine compartment, follow the fuel line from the tank until the fuel filter is located.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 If the fuel filter has a clear case, inspect the filter element for dirt.

Step 3 If the fuel filter case is not see-through, remove it from the fuel line. Drain the fuel from the filter into a container and inspect the condition of the fuel.
o Tip: Caution: Before removing fuel lines or fuel related parts, make sure that the fuel pressure is relieved from the vehicle fuel system. To relieve the pressure in fuel injected systems, remove the fuel pump fuse and run the engine.

Step 4 Install the new fuel filter making sure that the flow is in the correct direction. The arrow on the fuel filter is the direction of flow from the tank to the engine.

Step 5 Secure the lines back onto the fuel filter. If applicable, reinstall the fuel pump fuse.

Step 6 Start the engine and check for fuel leaks.

Step 7 Test drive the vehicle to check for a rough running engine, hesitation, or lack of power.


Hope this help (remember rated this).

Mar 25, 2010 | 1994 Toyota Camry

1 Answer

How do I replace the fuel filter in my 1997 rodeo?


Isuzu Rodeo - How to Replace a Fuel Filter
( DIY Complexity: Moderate / Time: 1.4 hours)

Parts:
1. Fuel Filter - $8.40

7e59050.jpg

Tools:
1. 3/8 in. Drive Ratchet
2. Hose Pincher
3. Flare Nut Wrench
4. Flat Head Screwdriver
5. Socket Set

Steps:
Step 1 * Open the hood and locate the fuel filter. If the fuel filter is not in the engine compartment, follow the fuel line from the tank until the fuel filter is located.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 * If the fuel filter has a clear case, inspect the filter element for dirt.

Step 3 * If the fuel filter case is not see-through, remove it from the fuel line. Drain the fuel from the filter into a container and inspect the condition of the fuel.
o Tip: Caution: Before removing fuel lines or fuel related parts, make sure that the fuel pressure is relieved from the vehicle fuel system. To relieve the pressure in fuel injected systems, remove the fuel pump fuse and run the engine.

Step 4 * Install the new fuel filter making sure that the flow is in the correct direction. The arrow on the fuel filter is the direction of flow from the tank to the engine.

Step 5 * Secure the lines back onto the fuel filter. If applicable, reinstall the fuel pump fuse.

Step 6 * Start the engine and check for fuel leaks.

Step 7 * Test drive the vehicle to check for a rough running engine, hesitation, or lack of power.


I really hope help with this (remember rated and comment this help).

Mar 10, 2010 | 1997 Isuzu Rodeo

2 Answers

Adjusting fuel pump


If you have the 91 3.1 V6 Rodeo you can't adjust the fuel pump or fuel pressure. The only thing you can really do is to get a throttle body rebuild kit that will have a new diaphragm for the fuel pressure regulator. If you want to adjust it, you'll have to get an aftermarket regulator and install on the return line (the smaller line) and remove the spring out of the regulator on the throttle body. If you feel the fuel pressure is too low, then you might need to change the pump. Its located in the fuel tank, only takes 1 or 2 hours to do.

Jul 12, 2009 | 1991 Isuzu Rodeo

1 Answer

Where is the fuel filter in my 1992 Isuzu Rodeo?


Look on passenger side frame rail ahead of the rear wheel in a bracket with a fuel line on each end. Before starting replacement-- be sure to release pressure from fuel lines, by removing fuel pump fuse under hood and running engine to use gas from lines. I then remove fuel lines by moving clamps away from fitting so hose can be pulled loose from old filter while it is still in bracket. On top of mounting is a bolt that holds filter clamp in place . After removing clamp and filter from mounting bracket, loosen filter body clamp and slip oout old filter-- then in with the new filter. Then reverse your steps to install filter. After filter is back in place -- reinstall fuel pump fuse, turn on key for a few seconds for gas to refill lines, then start engine and check your installation to make sure you have no fuel leaks at line connections.

Oct 18, 2008 | 1992 Isuzu Rodeo

Not finding what you are looking for?
1994 Isuzu Rodeo Logo

Related Topics:

363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...