Question about 1996 Jeep Cherokee Country

1 Answer

How to remove the ignition switch

Hi, my ignition switch has failed. can you tell me the procedures to remove it so i can install a new one? it's a 1996 jeep grand cherokee laredo 4x4 with tilt steering. 4.0 engine
thanks
Roger phillips

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

The best thing to do is call a locksmith so you dont accidentally break anything.if you already have the swotch it wont cost more than 40.00 or so to have it changed out

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition switch removal


here is the procedure can't remove the wires until you remove the key tumbler.

1. Disconnect the battery ground cable.
2. Remove the steering column filler panel.
3. Remove the knee bolster bracket.
4. Remove the instrument panel (I/P) cluster trim plate.
5. Remove the ignition switch bolts.
6. Lower the ignition switch away from the instrument carrier.
7. Insert the key into the ignition lock cylinder. Turn the key to the ON/RUN position.
8. Depress the retainer to release the transaxle park/lock cable. Remove the park/lock cable from the ignition switch by pulling on the cable.

Important: You cannot remove the Passlock(TM) electrical connector until the lock cylinder is removed

9. Depress and hold the detent on the bottom of the ignition switch in order to release the ignition lock cylinder. Remove the ignition lock cylinder with the key.
10. Disconnect the Passlock(TM) electrical connector.
11. Disconnect the electrical connectors

12. Use the following procedure if the ignition switch lock cylinder is seized or won't rotate:

1. Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.
2. Locate the surface for the release button (2) for the ignition switch lock cylinder on the plastic ignition switch housing. Center punch a location (1) on the rib approximately 3/8 inch reward, toward the key entry end, from the cylinder release button.
3. Carefully drill a pilot hole through the plastic housing with a 1/8-inch drill bit.
4. Using a 9/32-inch drill bit, carefully drill a larger hole at the pilot location, and slightly into the surface of the ignition switch lock cylinder, to break the release button retaining spring.
5. Remove portions of the broken spring from the hole using a small suitable tool.
6. Grasp the ignition switch lock cylinder and remove the cylinder from the switch housing.
7. Remove any plastic flash from the drilling operation, and using compressed air blow out the ignition switch assembly.
8. Follow Service Data procedures when cylinder coding is required. Refer to Key and Lock Cylinder Coding.

Installation Procedure

1. If the lock cylinder would not rotate or was seized, perform the following procedure:

1. Install the new ignition switch lock cylinder as required by rotating both the cylinder and the ignition switch to the ON position.
2. Push the ignition switch lock cylinder into the ignition switch housing until fully seated.
3. You may have to slightly depress the release button as the button passes by the 9/32-in hole previously drilled in the ignition switch housing
2. Connect the electrical connectors.
3. Connect the Passlock(TM) electrical connector.
4. Connect the park/lock cable to the ignition switch
5. Turn the key to the ON/RUN position. Install the ignition lock cylinder into the ignition switch. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
6. Remove the key

7. Position the ignition switch to the instrument carrier.

Notice: Refer to Fastener Notice in Service Precautions.

8. Install the ignition switch bolts.

Tighten the bolts to 10 N.m (89 lb in).

9. Install the trim plate bezel to the I/P cluster.
10. Install the knee bolster bracket.
11. Install the steering column filler panel.
12. Connect the battery ground cable

here are the diagrams too and good luck!
cf5a3c19-5b49-4036-9763-320025f7769e.gif 1803b10b-7885-49ce-8dea-eb3c9d239b80.gif 40925797-2b33-43e6-9245-a3d579edf645.gif 39db686b-5b37-4e74-b7ea-6653178ff643.gif f1e60817-d4d7-43d1-a113-437e4c91f2f3.gif

Apr 10, 2014 | 2002 Chevrolet Monte Carlo

1 Answer

Relay switch


Ignition and Start Switch Replacement
Removal Procedure
2c23f8d.jpg Disconnect the battery ground cable. .
Remove the steering column filler panel.
Remove the knee bolster bracket.
Remove the instrument panel (I/P) cluster trim panel.
Remove the ignition switch bolts.
Lower the ignition switch away from the instrument carrier.
Insert the key into the ignition lock cylinder. Turn the key to the ON/RUN position.
Depress the transaxle park/lock cable retainer to release. Pull to remove the park/lock cable from the ignition switch.
Important: The Passlock? electrical connector cannot be removed until the lock cylinder is removed.

Depress and hold the detent on the bottom of the ignition switch in order to release the ignition lock cylinder. Remove the ignition lock cylinder with the key.
d857e46.jpg Disconnect the Passlock? electrical connector.
Disconnect the electrical connectors.
4093e3a.jpg Important: Ignition switch lock cylinder that won't rotate or is seized.

Perform the following procedure if the ignition switch lock cylinder is seized or won't rotate.
12.1. Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.

12.2. Locate the surface for the ignition switch lock cylinder release button (2) on the plastic ignition switch housing and center punch a location (1) on the "rib" approximately 3/8 inch reward (toward the key entry end) from the cylinder release button.

12.3. Carefully drill a hole through the plastic housing with a 1/8 inch drill bit.

12.4. Carefully drill a larger hole at the pilot location, and slightly into the ignition switch lock cylinder surface to break the release button retaining spring using a 9/32 inch drill bit.

12.5. Remove portions of the broken spring from the hole using a small suitable tool.

12.6. Grasp the ignition switch lock cylinder and remove it from the switch housing.

12.7. Remove any plastic "flash" from the drilling operation, and using compressed air blow out the ignition switch assembly.

12.8. Follow service manual procedures when cylinder cording is required. Refer to Key and Lock Cylinder Coding in General Information.

Installation Procedure
If the lock cylinder would not rotate or was seized, perform the following procedure:
1.1. Install the new ignition switch lock cylinder as required by rotating both the cylinder and the ignition switch to the ON position.

1.2. Push the ignition switch lock cylinder into the ignition switch housing until fully seated.

1.3. You may have to slightly depress the release button as the button passes by the 9/32-in hole previously drilled in the ignition switch housing.
9600af8.jpg Connect the electrical connectors.
Connect the Passlock? electrical connector.
Connect the park/lock cable to the ignition switchdd765ba.jpg Turn the key to the ON/RUN position. Install the ignition lock cylinder into the ignition switch. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
Remove the key
681874a.jpg Position the ignition switch to the instrument carrier.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Install the ignition switch bolts.
Tighten

Tighten the bolts to 10 N?m (89 lb in).

Install the trim plate bezel to the I/P cluster. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Install the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Install the steering column filler panel. Refer to Steering Column Filler Replacement .
Connect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.

Dec 05, 2013 | 2005 Chevrolet Impala

1 Answer

On my altima 96 when I'm parking or turning extremely slow the steering wheel somewhat locks


Hi, can you tell if it's the lock in the steering column or something with the power steering instead? If it feels like the power steering, check the belt for looseness and tighten as needed. If it feels like it's in the column, your locking assembly may be coming loose inside. Below is a procedure for removing the steering wheel lock for inspection. Please let me know if you have questions, and thanks for using FixYa.


REMOVAL & INSTALLATION The steering lock/ignition switch/warning buzzer switch assembly is attached to the steering column by special bolts whose heads shear off upon installation. The bolts must be drilled out to remove the assembly or be removed with an appropriate tool. The bolts may also be removed with a hammer and chisel by notching the bolts and tapping them counterclockwise with the hammer and chisel.
The ignition switch or warning switch can be replaced without removing the steering lock assembly. The ignition switch is on the back of the assembly and the warning switch is on the side.


CAUTION The models covered by this guide may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Chassis Electrical .

  1. Disable the air bag system by disconnecting the negative battery cable and waiting at least 10 minutes, prior to starting this procedure.
  2. Remove the steering column covers.
  3. Remove the steering wheel.
  4. Remove the spiral cable assembly.
  5. Remove the combination switch from the steering column.
  6. Remove the steering column support nuts and lower the steering column.
  7. Disconnect the ignition switch wiring.
  8. Remove the bolts that secure the steering lock and remove the steering lock assembly.

To install:
  1. Install the steering lock assembly and secure with new shear type bolts.
  2. Connect the ignition switch wiring harness.
  3. Raise the steering column and secure with mounting nuts. Tighten the mounting nuts to 11-14 ft. lbs. (15-19 Nm).
  4. Install the spiral cable assembly.
  5. Install the combination switch.
  6. Install the steering column covers.
  7. Install the steering wheel.
  8. Connect the negative battery cable.

Apr 04, 2011 | 1996 Nissan Altima

1 Answer

Need to replace ignition cylinder. no keys


This is not an easy repair due to anit theft requirements. need to chisel off bolts.

Section 11-04: Steering Column 1997 Probe Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000
Ignition Switch Lock Cylinder Removal
  1. Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the four lower steering column shroud screws.


    j5021c.gif

  1. Separate the upper and lower steering column shrouds.
  1. Remove the ignition switch lock cylinder illumination miniature bulb from the lower steering column shroud.
  1. Remove the upper and lower steering column shrouds.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal and installation procedure.
  1. If equipped, remove the ignition/shifter interlock cable screw.
  1. Disconnect the ignition/shifter interlock cable (3F719) from ignition switch lock cylinder (11582).
  1. Use a chisel to remove the two ignition switch lock cylinder bolts.
  1. Remove the ignition switch lock cylinder from the steering column.
  1. Disconnect the ignition key reminder switch electrical connector.
  1. If necessary, remove the ignition key reminder switch.


    j5028b.gif

Installation
NOTE: Use new ignition switch lock cylinder bolts. Tighten the bolts until the bolt heads break off. Check for proper ignition switch (11572) operation.

To install, reverse the removal procedure.

Mar 25, 2011 | 1997 Ford Probe

1 Answer

Ignition switch is broke


Here are procedures for removing the ignitionlock assy. If equipped with SRS, extra care must be taken while removing ang installing to avoid damage to the SRS cable reel.

IGNITION SWITCH & LOCK CYLINDER
Removal
1. Remove steering wheel and combination switch (if necessary). Disconnect ignition switch harness connectors. If shear bolt studs are accessible, use a hacksaw to cut slots into exposed studs.

2. Remove studs using a screwdriver. If shear bolt studs are recessed or hard to reach with hacksaw, use a center punch on studs. Using a drill bit and screw extractor, remove studs. Place key in ACC position and remove ignition switch and lock cylinder.

Installation

To install, reverse removal procedure. Install NEW shear bolts. Tighten shear bolts finger tight. Ensure proper operation of ignition switch and lock cylinder. Tighten shear bolts until heads break off. Install combination switch, upper and lower steering column covers and steering wheel (if removed). Tighten steering wheel nut and Torx screws to specification.

Sep 26, 2010 | 1996 Toyota Avalon

1 Answer

How do i replace the ignition switch?


Removal
Remove steering wheel and combination switch. See STEERING WHEEL & AIR BAG and
COMBINATION SWITCH . Disconnect ignition switch electrical connector. Using a chisel and screwdriver,
back out bolts at steering lock bracket. Insert key into steering lock cylinder, and turn to ACC position. Using a
small Phillips screwdriver, push cylinder lock pin inward. On all models, remove ignition switch, steering lock
and bracket.
Installation
To install, reverse removal procedure. Use NEW steering lock bracket and bolts. Temporarily install ignition
switch and steering lock cylinder onto steering column. Ensure ignition switch functions normally, then tighten
steering lock cylinder bolts. Tighten lock bolts until heads twist off. To complete installation, reverse removal
procedure.
If you need anymore info let me know.

Jun 19, 2010 | 2001 Mitsubishi Eclipse

2 Answers

I have a 99 voyager and the ignition will not turn how do I remove it


Here's a copy of a service bulletin on your problem.

I'll bet the dealer says $300 for parts and 2 hrs labor.:screwy:

Ignition Key - Will Not Turn And/Or Cannot Be Removed
NUMBER: 23-23-00
GROUP: Body
DATE: JUNE 30, 2000
SUBJECT:
Ignition Key Will Not Turn And/Or Cannot Be Removed
MODELS:
1997 - 2000 (NS) Town & Country/Caravan/Voyager
OVERVIEW:
This bulletin involves performing one or any combination of the following procedures; cutting a new ignition key, and/or adjusting transmission shifter cable, and/or replacing the ignition lock cylinder and/or replacing the ignition lock housing and switch assembly.
SYMPTOM/CONDITION:
1. Cannot turn the ignition key when attempting to start vehicle, this condition may be intermittent.
2. Unable to remove the ignition key from the lock cylinder.
PARTS REQUIRED:
AR(1)04778115 Key
AR(1)05003843AB Cylinder, Ignition Lock
AR(1)04690523 Assembly, Ignition Switch and Lock Housing
EQUIPMENT POSSIBLY REQUIRED:
Key Cutter such as Pentastar Service Equipment (PSE) IL-MK1-P2627 or
IL-ECM-100
T-27 Torx Bit
T-25 Torx Bit
T-10 Tamper Resistant Torx Bit
SR-706059 Lock Cylinder Build Kit, Pentastar Service Equipment (PSE)
DIAGNOSIS/REPAIR PROCEDURE:
DOES NOT REQUIRE HOISTS OR OTHER FULL SERVICE FACILITY SPECIAL EQUIPMENT. THIS REPAIR IS COMPATIBLE WITH DAIMLERCHRYSLERS MOBILE SERVICE PROGRAM.
SYMPTOM/CONDITION ONE
1. Ensure the steering wheel is centered and the vehicle is positioned on a level surface.
2. Disconnect the negative battery cable.
3. Insert ignition key into the ignition lock cylinder and attempt to rotate the key to the start position and then the accessory position.
4. If the key does not turn, remove the key from the lock cylinder and rotate it 180°. Reinsert the key into the lock cylinder and attempt to rotate the key. If the key does not turn skip to step 14. If the key does turn make a new key.
NOTE: USE THE KEY CODE ON THE VEHICLE INVOICE TO CORRECTLY CUT THE NEW KEY. KEY CODES ARE ALSO AVAILABLE USING THE D.I.A.L. SYSTEM, MAIN MENU OPTION 13. DO NOT USE A KEY DUPLICATOR TO MAKE THE NEW KEY.
5. Insert the new ignition key into the ignition lock cylinder and attempt to rotate the key to the start position and then the accessory position.
6. If the key turns, remove the key from the lock cylinder and turn it over 180°and reinsert the key into the lock cylinder. Attempt to rotate the key.
7. If the key turns, repeat steps 5 and 6 ten times. If the key continues to rotate smoothly the repair is complete. If the key fails to turn smoothly at each rotation attempt, continue to step 8.
8. Remove the ignition lock cylinder using the procedure outlined on page 8D-29 of the 2000 Town & Country, Caravan and Voyager Service Manual (Publication No. 81-370-0005). DO NOT ATTEMPT TO DISASSEMBLE THE Lock CYLINDER.
9. Build a new lock cylinder to the key code on the vehicle invoice, using the instructions in the Pentastar Service Equipment SR-706059 Lock Cylinder Build Kit.
10. Install the new ignition lock cylinder using the procedure outlined on page 8D-29 of the 2000 Town & Country, Caravan and Voyager Service Manual (Publication No. 81-370-0005).
11. Insert the new ignition key into the new ignition lock cylinder and attempt to rotate the key to the start position and then the accessory position.
12. If the key turns, remove the key from the lock cylinder and turn it over 180°and reinsert the key into the lock cylinder. Attempt to rotate the key.
13. If the key turns, repeat steps 11 and 12 ten times. If the key continues to rotate smoothly the repair is complete. If the key fails to turn smoothly at each rotation attempt, continue to step 14.
14. Remove the ignition lock housing and ignition switch as an assembly using the procedure outlined beginning on page 19-47 of the 2000 Town & Country, Caravan and Voyager Service Manual (Publication No. 81-370-0005).
NOTE: SKIP STEPS 13 AND 14 OF THE SERVICE MANUAL REMOVAL PROCEDURE SO THE IGNITION LOCK HOUSING AND IGNITION SWITCH ARE REMOVED AS AN ASSEMBLY.
15. Install a new ignition lock housing and ignition switch assembly, p/n 04690523, using the procedure outlined beginning on page 19-49 of the 2000 Town & Country, Caravan and Voyager Service Manual (Publication No. 81-370-0005).
NOTE: PRIOR TO PERFORMING STEP 2 OF THE SERVICE MANUAL LOCK HOUSING INSTALLATION PROCEDURE, INSTALL THEN REMOVE THE TWO LOCK CYLINDER HOUSING MOUNTING SCREWS INTO THE LOCK HOUSING MOUNTING HOLES TO CREATE THE THREADS IN THE HOLES.FAILURE TO CREATE THE MOUNTING HOLE THREADS PRIOR TO INSTALLATION TO THE STEERING COLUMN MAY CAUSE MISALIGNMENT OF THE LOCK HOUSING TO STEERING COLUMN AND DAMAGE BINDING OF STEERING COLUMN MAY RESULT.
STEPS 5 AND 6 OF THE SERVICE MANUAL INSTALLATION PROCEDURE FOR THE LOCK HOUSING ARE NOT NECESSARY FOR THIS TSB PROCEDURE.
WHEN PERFORMING STEP 9 OF THE SERVICE MANUAL PROCEDURE USE THE NEW LOCK CYLINDER THAT WAS BUILT IN STEP 9 OF THE SYMPTOM/CONDITION ONE DIAGNOSIS / REPAIR PROCEDURE OF THIS BULLETIN.
16. Insert the new ignition key into the new ignition lock cylinder and attempt to rotate the key to the start position and then the accessory position.
17. If the key turns, remove the key from the lock cylinder and turn it over 180°and reinsert the key into the lock cylinder. Attempt to rotate the key.
18. If the key turns, repeat steps 16 and 17 ten times. If the key continues to rotate smoothly the repair is complete.
SYMPTOM/CONDITION TWO
1. Check the operation of the shift lever. The shift lever should fall freely away from the driver when it is brought up into the Park position.
2. If the shift lever does not seat fully up and away from the driver the column will not allow the key to be removed.
3. If binding of the shift lever is discovered, adjust the transmission shift cable using the procedure outlined on page 21-114 of the 2000 Town & Country, Caravan and Voyager Service Manual (Publication No. 81-370-0005).

Jun 01, 2010 | 1999 Plymouth Grand Voyager

1 Answer

Ignition switch replacment


Ignition Switch REMOVAL & INSTALLATION The ignition switch is located at the bottom of the ignition key cylinder body. To remove the ignition switch, first remove the ignition lock cylinder.

1993–99 Golf and Jetta
  1. Disconnect the negative battery cable.
  2. Center the steering wheel.
  3. Remove the air bag.
  4. Remove the steering column switches.
  5. If the vehicle is equipped with an automatic transmission, detach the shift lock cable from the lock cylinder housing.
  6. Remove the adapter sleeve from the steering column.
  7. Remove the spring and horn contact ring from the steering column assembly.
  8. Detach the sheer bolt.
  9. Insert the ignition key and unlock the cylinder, then detach the wiring connectors.
  10. Once all wiring has been detached, slide the housing off the steering column.
  11. Mark and drill the lock cylinder as shown and described in the above procedure.
  12. Compress the stop spring and pull the lock cylinder out of the steering column housing.
  13. Put the new lock cylinder into the steering lock housing.
  14. Insert the key into the lock cylinder.
  15. While you gently turn the key, insert the lock cylinder fully into the housing.
  16. The rest of the installation procedure is the reverse of removal. NOTE: Always use a new shear pin when installing the lock cylinder.

Jun 25, 2009 | 1998 Volkswagen Jetta

1 Answer

Remove ignition tumbler


lock cylinder removal

Section 11-04: Steering Column 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder Removal
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR DRIVER SIDE AIR BAG MODULE DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY DRIVER SIDE AIR BAG MODULE SYSTEM COMPONENTS.
    Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal procedure.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the ignition/shifter interlock cable mounting bracket bolt and position the ignition/shifter interlock cable mounting bracket and the ignition/shifter interlock cable (3F719) aside.




  1. Remove the four steering column upper mounting bracket bolts and lower the steering column (3C529).
  1. Use a hammer and chisel to make a groove in the head of each of the two ignition switch lock cylinder bracket bolts.


    0764353.gif

  1. Remove the two ignition switch lock cylinder bracket bolts with a screwdriver and discard the bolts.




  1. Remove the ignition switch lock cylinder and the ignition switch lock cylinder bracket.
Installation
  1. Position the ignition switch lock cylinder and bracket and install two new bolts, tightening them only enough to hold the ignition switch lock cylinder in position.
  1. With the key in the ignition, verify the operation of the ignition switch lock cylinder. If necessary, reposition the ignition switch lock cylinder until it operates properly.
  1. Tighten the ignition switch lock cylinder bracket bolts until the bolt heads break off.
  1. Position the steering column and install the four steering column upper mounting bracket bolts. Tighten the steering column upper mounting bracket bolts to 9-14 Nm (80-124 lb-in).
  1. On vehicles equipped with tilt column, remove the upper mounting bracket retaining pin.
  1. Position the ignition/shifter interlock cable mounting bracket and install the bolt. Tighten the ignition/shifter interlock cable mounting bracket bolt to 4-6 Nm (35-53 lb-in).
  1. Connect the ignition switch electrical connector.
  1. Install the multi-function switch. Refer to Section 11-05 for the installation procedure.
  1. Install the steering wheel. Refer to the procedure in this section.
  1. Inspect the shift interlock system. Refer to Section 07-05 for the procedure.

Apr 07, 2009 | 1995 Mercury Tracer

5 Answers

Diagram on a pontiac grand prix


Ignition Switch GM Century/Lumina/Grand Prix/Intrigue 1997-2000 The vehicles covered by this guide use one of two types of ignition switches:
  • A mechanical key and lock cylinder built into the steering column, that works a pull rod to actuate the separate electrical portion of the ignition switch mounted further down the steering column. For more information and replacement procedures on this type of switch, please see .
  • An instrument panel-mounted ignition switch is also used on some W-Body vehicles. To service this switch, the radio, heater & A/C control panel and the instrument cluster must be removed. All of these procedures are found elsewhere in this section.
REMOVAL & INSTALLATION
Instrument Panel-Mounted Ignition Switch
WARNING You must perform the Body Control Module (BCM) theft deterrent relearn procedure after replacement of the ignition lock cylinder. Failure to perform this relearn procedure means the BCM will not function properly. This means the vehicle will not be theft protected by the Passlock system and the engine may not crank or start. GM recommends that this procedure be performed with their Tech 2® or equivalent scan tool. An alternate relearn procedure is given at the end of this procedure.
  1. Disconnect the negative battery cable.
  2. Remove the radio assembly following the procedures found in this section.
  3. Remove the heater & A/C control head assembly following the procedures found in this section.
  4. Remove the instrument cluster assembly following the procedures found in this section.
  5. Detach the electrical connectors from the ignition switch.
  6. Insert the key and turn the ignition switch lock cylinder to the ACC position.
  7. Depress the transaxle park/lock cable retainer to release, then pull to remove the cable from the ignition switch.
NOTE You must perform the Body Control Module theft deterrent relearn procedure after replacement of the ignition lock cylinder.
  1. If it is necessary to remove the ignition lock cylinder from the ignition switch (theft damage, etc.), use the following procedure:
    1. Insert the key and turn the ignition switch lock cylinder to the ON position.
    2. Using a small flat-bladed tool, depress and hold the lock cylinder retaining tab.
    3. Using the key as an aid, pull to remove the ignition switch lock cylinder from the switch.
    4. Remove the key from the lock cylinder.
    5. Carefully pull to release the ignition switch bezel from the ignition switch lock cylinder.
  2. Remove the ignition switch bracket bolts and remove the ignition switch through the instrument panel cluster opening.
  3. Remove the bolts retaining the ignition switch to the bracket and remove the bracket.
0900c15280090fea.jpgRemoving an instrument panel-mounted ignition switch assembly—1998 Oldsmobile Intrigue shown, others similar To install:
  1. Install the ignition switch to its bracket and install the bolts. Install the ignition switch into position through the instrument panel cluster opening and install the bracket retaining bolts.
  2. If removed, install the ignition switch lock cylinder to the ignition switch using the following procedure:
    1. Recode the lock cylinder, if necessary.
    2. Align the ignition switch bezel to the tabs on the ignition switch lock cylinder and carefully press to secure in place.
    3. Insert the key and turn the ignition switch lock cylinder to the ON position.
    4. Align the ignition switch lock cylinder to the ignition switch, then press into place.
  3. Turn the key to the ACC position. Align and press into place the transaxle park/lock cable to the ignition switch. Remove the key from the switch.
  4. Attach the electrical connectors to the ignition switch.
  5. Install the instrument cluster using the procedures found in this section.
  6. Install the heater & A/C control panel using the procedures found in this section.
  7. Install the radio assembly using the procedures found in this section.
  8. Connect the negative battery cable.
  9. If the lock cylinder was removed, perform the BCM Programming/RPO Configuration procedure.
THEFT DETERENT RE-LEARN—WITHOUT TECH 1®SCAN TOOL
This procedure takes approximately 30 minutes. Make sure the battery is fully charged before proceeding.
  1. Turn the ignition switch to the OFF position.
  2. Turn the ignition switch all the way from the OFF to the START position, then leave it in the ON position. The engine will not crank.
  3. The SECURITY light should come on and stay on for at lease ten minutes.
  4. Turn the ignition switch to the OFF position for five seconds.
  5. Repeat Steps 2, 3 and 4 again for a second time.
  6. Repeat Steps 2, 3 and 4 again for a third time.
  7. Turn the ignition switch to the OFF position.
  8. Turn the ignition switch all the way to the START position. The engine should now start.

Sep 09, 2008 | 2000 Pontiac Grand Prix

Not finding what you are looking for?
1996 Jeep Cherokee Country Logo

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...