Question about 2008 Toyota Camry

1 Answer

Change a turn signal bulb on a 2008 Camry

How do I change the bulb? It looks like I hav eto completely remove the lens itself. If so, how do I do it?

Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

You can see two screws holding this lens assembly, remove them and you can slide the lens off the cavity.

the wires and socket would be exposed, twist the socket counter clock wise and the bulb would be exposed.

replace the bulb and do the reverse in installing the signal light assembly back to the cavity.


tnx 4 using fixya,


drcool

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

1 Answer

How do you change the parking lights


Signal and Marker Lights
REMOVAL & INSTALLATION
Front Turn Signal and Parking Lights
1991-96 MODELS

  1. Remove the lens upper retaining screw and the fender side retaining screw.
  2. Slide the lens assembly forward until access to the rear is possible.
  3. If necessary, unplug the bulb electrical connection.
  4. Turn the bulb socket assembly counterclockwise and remove it from the lens.
  5. Depress and twist the bulb approximately 1?8 turn
    counterclockwise, then remove it from the socket.





    Fig. 1: Remove the lens upper retaining screw and the fender
    side retaining screw
    90986p79.jpg






    Fig. 2: If necessary, unplug the bulb's electrical connection
    90986p90.jpg






    Fig. 3: Turn the bulb socket assembly counterclockwise and remove it from the lens 90986p91.jpg






    Fig. 4: Remove the bulb from the socket
    90986p92.jpg

    To install:

  6. Align the bulb's locating pins, then install the bulb in the socket.
  7. Attach the socket to the lens and turn it clockwise to engage it.
  8. If removed, attach the bulb electrical connection.
  9. Place the lens into position, then tighten the fender side and upper
    retaining screws.

Oct 31, 2010 | 1991 Mercury Tracer

1 Answer

How do i changs rear turn signal bulb. it looks difficult.


not too difficult. you have to go thru your trunk. Carefully peel away the trunk liner where your rear lenses are. There are three nuts you have to unscrew to pull out the entire lens. carefully unscrew and push out the lens into your free hand. locate & replace the faulty bulb, and re-attach the lens and put back the trunk liner.

Oct 18, 2010 | 2008 Pontiac G6

1 Answer

How do I change the rear turn signal bulb on a 2004 Sebring convertible?


Peel back the trunk lining to reveal three wing nuts. Remove wing nuts to pull lens cap away from car. To remove bulb socket push on the rectangular button (the release) while pushing on the end of the socket to unlock and spin counter clockwise to release. pull out old bulb and reinstall lens cap.

May 21, 2010 | Cars & Trucks

1 Answer

How do you install turn signal lens on side mirrors on a 2005 F250?


- Adjust the mirror so the mirror glass is in as far as it will go (meaning if you were looking in the mirror you would see the side of the truck)

- Look inside the mirror housing
- Locate silver clip
- Using a flat screw driver, push the clip in
- Lenses will pop out on the outside
- Remove bulb
- Replace bulb
- Snap back together when new bulb in place.

May 02, 2010 | 2008 Ford F-250 Super Duty

3 Answers

1995 Toyota Camry tail light. no screws to


To change a bulb on this car you will need to go from the trunk. The bulbs are located behind a small plastic door.

Oct 28, 2009 | 1995 Toyota Camry

1 Answer

How do you replace the front turn signal bulb? I am having a difficult time.


turn signals are replaced one of two ways from the inside or the outside. #1 If they are replaced from the outside there will be a couple of screws on the out side of the lens take these out and the whole lens will come out turn the socket on back of lens and the bulb will be right there push bulb in and turn change bulb and reassemble. #2 you have to get at it from under the hood look from on top of signal or look up from under car you must get to the socket turn it and the bulb will be there push bulb in and turn replace bulb.

Oct 17, 2009 | 2002 Buick LeSabre

1 Answer

Rear Light Bulb Replacement


unfortunately you will have to remove the assembly to get to the bulbs

Jan 08, 2009 | 2001 Buick LeSabre

1 Answer

2008 Camry Front Turn signal Bulb


Front Open The Hood And View Back Of Headlight Turn And Then Pull Light.
Rear Open Trunk And Remove Carpet From Behind Light Now You Can View The Bulb Housing Turn And Pull.

Nov 16, 2008 | 2008 Toyota Camry

Not finding what you are looking for?
2008 Toyota Camry Logo

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...