Question about 2008 Toyota Camry

1 Answer

2008 Camry Front Turn signal Bulb

How do I replace a burnt out fron turn sigal bulb for a 2008 Camry?

Posted by on

  • 1 more comment 
  • Anonymous Mar 14, 2014

    2008 Lincoln MKZ turn signal bulb

  • Anonymous Mar 28, 2014

    how to change the front blinker bulb

  • Anonymous Mar 29, 2014

    Replace bumper mounted front turn signal assembly

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 716 Answers

Front Open The Hood And View Back Of Headlight Turn And Then Pull Light.
Rear Open Trunk And Remove Carpet From Behind Light Now You Can View The Bulb Housing Turn And Pull.

Posted on Jan 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

2 Answers

My 2008 Chevy Cobalt coupe has a passenger side turn signal that flashes fast on the instrument panel. However, no turn bulb is burnt out in either the front or rear. The rear passenger turn blub just...


It is as simple as your hazzard switch needs to be replaced yes your hazzard switch as now turn signals are built threw the hazzard switch my PT Cruiser had same problem as my s10 replaced hazzard switch fixed the problem

Aug 18, 2011 | 2008 Chevrolet Cobalt

3 Answers

Rapid right turn signal on dash but no right rear turn ligt at all


What that rapid turn signal on the dash means is, the rear turn signal tail light is burnt out. This is how you know the bulb is bad. Replace the burnt out tail light bulb and you will be back to normal.

Jan 16, 2011 | 2008 Chevrolet Impala

2 Answers

My left turn signal goes too fast when i want to make a left turn but my right turn signal is fine... how do i make the left one normal again?


Replace the burned out bulb. It is flashing fast to alert you that bulb is burnt out. Turn on the side that works properly & note all bulbs flashing in front, rear & side. Most likely there is at least 1 burnt out on the other side.

Jun 25, 2010 | 2001 Cadillac DeVille

1 Answer

2004 Dodge Durango: Left turn signal blinks fast


Check the bulb socket for a burnt or a shorted condition. Remove bulb and try another bulb, if it does it again then you have a short in the socket or wiring to bulb. Turn on the 4 way flashers and see what it will do. If it continues then look for any burnt wire connector or wireing to bulb. Check the wiring behind the light for any metal that has cut into the wiring insulation. Hope this will help you.

May 23, 2010 | 2004 Dodge Durango

2 Answers

Right front turn signal not working at all right rear flashes fast? 2004 Impala


Sounds like your front turn bulb burnt out. When the turn signal operates fewer bulbs it works faster. You need to change the right front bulb.

Aug 09, 2009 | 2004 Chevrolet Impala

1 Answer

Want to change bulb in turn signal on bottom front of driver side


If there is no screws on lens, you may have to acsess it from under car, or under hood, twist plug and should come out to chg. bulb.

Feb 13, 2009 | 2000 Buick LeSabre

1 Answer

Change a turn signal bulb on a 2008 Camry


you can see two screws holding this lens assembly, remove them and you can slide the lens off the cavity.

the wires and socket would be exposed, twist the socket counter clock wise and the bulb would be exposed.

replace the bulb and do the reverse in installing the signal light assembly back to the cavity.


tnx 4 using fixya,


drcool

Nov 16, 2008 | 2008 Toyota Camry

2 Answers

Replacing front turn signal bulb on 2006 Cadillac SRX


You must take the front wheel off, then remove the inner front fender panels (2), they are fastened with plastic pushbuttons. this exposses the light housings for the turn and fog lambs. This takes about an hour, but saves you alot of money.

Nov 12, 2008 | 2006 Cadillac SRX

Not finding what you are looking for?
2008 Toyota Camry Logo

428 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...