Question about 1996 Pontiac Grand Am

2 Answers

1996 pontiac grand am se passlock1 or passlock2

I have A 1996 grand am se made in 05-96 does it have a passlock 1 or a passlock 2 in it? I am installing a remote starter in it and trying to find out what one it has. Can you help.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 436 Answers

Passlock 1

Posted on Oct 02, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

It has a passlock 2

Posted on Jun 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Grand Am SE A/C recharge location pictures


I searched "recharge air conditioning pontiac grand am" & got a fair number of hits. Suggest you try and see if there's any help there. It looks promising.

Jun 16, 2015 | 1996 Pontiac Grand Am

1 Answer

Firing order 1996 grand se 3.1


On 1996 Pontiac Grand AM 3.1 liter V-6 VIN "M"... Firing Order 1-2-3-4-5-6.

If you need this diagram or other information, countact us in the previous link.

Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa.

Oct 31, 2011 | 1996 Pontiac Grand Am

1 Answer

How to diable the passlock 1 on a 1996 pontiac sunfire?


Check out this link for options on disabling your passlock. http://vatspasslockpasskeysecurityhelp.yolasite.com/

Jun 05, 2011 | Pontiac Sunfire Cars & Trucks

1 Answer

How do you reset the theft system (for the car, not the radio) on a 1996 pontiac sunfire se. the battery went dead and the car has been sitting for a month now. the car will not start with the key. it will...


Your vehicle is equipped with the Passlock theft-deterrent system.
Passlock is a passive theft-deterrent systemT. he system is armed once the keyi s removed from the ignition. Passlock enables fuel if the ignition lock cylinderi s turned with a valid key. If a correct key is not used, fuel is disabled.

During normal operation, the THEFT SYSTEM light will go off after the engine is started. Ln the unlikely event that the engine stalls and the THEFT SYSTEM light flashes, wait until the light stopsf lashing before trying to restart the engine. Remember to release thkee y from the START position as soon as the engine starts. If after several tries the vehicle still does not start, the vehicle may need service. At this time, you may also want to check the fuses. See your Pontiac dealer for service.

If the THEFT SYSTEM light comes on while the engine is running, a problem has been detected and the system may need service. See your dealer for service. In an emergency, call the Pontiac Roadside Assistance Program at 1 -800-ROADSIDE or 1-800-762-3743.

This ans other details can find it in this link for 1996 Pontiac Sunfire - Owners Manual.

I hope helps (remember to rate and comment this).

Oct 13, 2010 | 1996 Pontiac Sunfire

1 Answer

1996 Grand Prix: How much for a tune up for my Pontiac Grand Prix S...


spark plugs, wires, oxygen sensors, fuel filter,air filter, oil, oil filter and while your at it, ac filter. In AL it will run you about 200 done yourself.

May 16, 2010 | 1996 Pontiac Grand Prix

1 Answer

Where is the starter located on a 91 grand prix se?


e12c4da.jpg

Fig.: Starter motor mounting-2.2L engine


58c758a.jpg

Fig.: Starter removal and installation-2.3L engine


8204771.jpg

Fig.: Starter motor mounting-2.5L engine


b967f34.jpg

Fig.: Starter motor mounting-1996 3.1L engine shown


Hope helped (remember comment and rates this).

Apr 16, 2010 | 1991 Pontiac Grand Prix

1 Answer

1996 buick skylark..alarm theft keeps flashin..try to start..it turns but wont stay running..


Need a bit more information, Is the security light on, have you checked for spark and fuel pressure, just in case you did and know it is the passlock system then check this out, hopefully it will ansewer your problem, please rate your mechanics help.
have a great day. Sorry the pictures won't come up, but check out the site

GM Passlock I & II Information

Please study the following information carefully WHEN INSTALLING REMOTE START systems on a 1996 or later GM car or truck.
Introduced in 1996, GM has changed the VATS anti theft system to Pass-Lock system. This is a similar device to the VATS system, in that there is a resistor present during the start cycle. However, in the PASSLOCK system, the resistor has been placed inside the ignition switch, instead of the key. See the GM V.A.T.S page for more information.
To remotely start a car with this feature, you must bypass the PASSLOCK system. There are two methods of doing so.. The first, is to permanently bypass this system. This is the easiest method for accomplishing your task. The second way, is to temporarily bypass the PASSLOCK, by introducing relays into the system, which retain all of the features of the system, while allowing your remotes start module to bypass it automatically during a remote start cycle.
Vehicles effected
(1996 and newer): N & J body cars, such as
Pontiac Sunfire and GrandAm Passlock-1
Chevrolet Cavalier Passlock-1
Buick Skylark Passlock-1
Oldsmobile Achieva Passlock-1

1997 or newer
Chevrolet Malibu Passlock-II
Oldsmobile Cutlass Passlock-II

1998 or newer
All trucks , SUVs and Vans Passlock-II

It is important to pay special attention to the fact that there are many different ways of achieving the same goal. There are actually 2 different Passlock-II systems. On the next page, there are tests to establish which type of passlock-II your car has.

Relays shown are standard automotive 5 pin spdt relays, available from IEI.
A multi meter is required to measure the resistance values. Accuracy is important within 5%.

Once the value of the resistor is measured, a resistor of the same value +/-5% must be purchased (Radio Shack2.gif, for example). You can also use a Potentiometer (POT), which can be adjusted to the same value of the resistor in the ignition switch.

pslc1.gif Passlock-I bypass procedure....

1: Remove the top and bottom shrouds from the steering column.
2: Find the 3 wire ribbon cable2.gif, coming from the ignition switch, containing White, Black, Yellow (Sometimes White, Black, Black). These are THIN wires.
3: Locate the Black 6 position connector on the LEFT side of the steering column, right above the ignition switch position. There is a BLACK (Thin) wire in this connector, called "Bulb Test", which shows Ground with ignition in the Off position, OPEN in the "Run" position, and GROUND in the "Crank" position.
4: Turn the ignition switch to the "Run" position. Do not crank the car.
5: Cut the Thin Yellow wire and strip both ends.
6: Without cutting the Black wire, expose some of the copper.
7: Using the ohmmeter, measure from the Yellow wire (the end coming from the ignition switch), to the exposed Black wire and record the value. Measure more than once to assure you have the right value.
8: Acquire the same size resistor and 3 relays, and perform the connections shown in the diagram below.

pslk2.gif PASSLOCK-II bypass procedure

There are 2 types of Passlock-II systems. To determine which system you have, follow these instructions;

1: Locate two wires, which are THIN and are in the main ignition harness.. Orange/Black (or Black) and Yellow.
2: Cut the Yellow wire, and strip back some of the insulation from the Orange/Black (Or Black) wires.
3: Turn the ignition to the "Run" position ( don't crank the starter). Measure and record the value measured from the KEY SIDE of the Yellow wire, to the Black/Orange wire.
4: Turn the key to the "Crank" position and release. Now read the value again.
pslk3.gif5: If the value changed, follow "Method#1". If the value stayed the same, follow "Method#2".



These diagrams are from our friends at ALARMTEK AUTO ALARM
Need additional assistance?

Oct 22, 2009 | 1996 Buick Skylark

2 Answers

2001 grand am gt 3.4 v6, has fire and fuel cranks but wont start


check to see if the security light is blinking, if it is. thats an easy fix.

Oct 18, 2009 | 2001 Pontiac Grand Am SE

2 Answers

My son has a 1999 grand am, just like the oneshown above. the car wont start because the security sys. shuts off the fuel sys. down. the manifold still has good pressure cause we just had thefuel pump...


Need a bit more information, Is the security light on, have you checked for spark and fuel pressure2.gif, just in case you did and know it is the passlock system then check this out, hopefully it will ansewer your problem, please rate your mechanics help.
have a great day. Sorry the pictures won't come up, but check out the site
GM Passlock I & II Information

Please study the following information carefully WHEN INSTALLING REMOTE START systems on a 1996 or later GM car or truck.
Introduced in 1996, GM has changed the VATS anti theft system to Pass-Lock system. This is a similar device to the VATS system, in that there is a resistor present2.gif during the start cycle. However, in the PASSLOCK system, the resistor has been placed inside the ignition switch, instead of the key. See the GM V.A.T.S page for more information.
To remotely start a car with this feature, you must bypass the PASSLOCK system. There are two methods of doing so.. The first, is to permanently bypass this system. This is the easiest method for accomplishing your task. The second way, is to temporarily bypass the PASSLOCK, by introducing relays into the system, which retain all of the features of the system, while allowing your remotes start module to bypass it automatically during a remote start cycle.
Vehicles effected
(1996 and newer): N & J body cars, such as
Pontiac Sunfire and GrandAm Passlock-1
Chevrolet2.gif Cavalier Passlock-1
Buick Skylark Passlock-1
Oldsmobile Achieva Passlock-1
1997 or newer
Chevrolet Malibu2.gif Passlock-II
Oldsmobile Cutlass Passlock-II
1998 or newer
All trucks , SUVs and Vans Passlock-II
It is important to pay special attention to the fact that there are many different ways of achieving the same goal. There are actually 2 different Passlock-II systems. On the next page, there are tests to establish which type of passlock-II your car has.
Relays shown are standard automotive 5 pin spdt relays, available from IEI.
A multi meter is required to measure the resistance values. Accuracy is important within 5%.
Once the value of the resistor is measured, a resistor of the samevalue +/-5% must be purchased (Radio Shack2.gif, for example). You can also use a Potentiometer (POT), which can be adjusted to the same value of the resistor in the ignition switch.

pslc1.gif Passlock-I bypass procedure....

1: Remove the top and bottom shrouds from the steering column.
2: Find the 3 wire ribbon cable2.gif, coming from the ignition switch, containing White, Black, Yellow (Sometimes White, Black, Black). These are THIN wires.
3: Locate the Black 6 position connector on the LEFT side of the steering column, right above the ignition switch position. There is a BLACK (Thin) wire in this connector, called "Bulb Test", which shows Ground with ignition in the Off position, OPEN in the "Run" position, and GROUND in the "Crank" position.
4: Turn the ignition switch to the "Run" position. Do not crank the car.
5: Cut the Thin Yellow wire and strip both ends.
6: Without cutting the Black wire, expose some of the copper.
7: Using the ohmmeter, measure from the Yellow wire (the end coming from the ignition switch), to the exposed Black wire and record the value. Measure more than once to assure you have the right value.
8: Acquire the same size resistor and 3 relays, and perform the connections shown in the diagram below.

pslk2.gif PASSLOCK-II bypass procedure

There are 2 types of Passlock-II systems. To determine which system you have, follow these instructions;

1: Locate two wires, which are THIN and are in the main ignition harness.. Orange/Black (or Black) and Yellow.
2: Cut the Yellow wire, and strip back some of the insulation from the Orange/Black (Or Black) wires.
3: Turn the ignition to the "Run" position ( don't crank the starter). Measure and record the value measured from the KEY SIDE of the Yellow wire, to the Black/Orange wire.
4: Turn the key to the "Crank" position and release. Now read the value again.
pslk3.gif5: If the value changed, follow "Method#1". If the value stayed the same, follow "Method#2".



These diagrams are from our friends at ALARMTEK AUTO ALARM

Oct 05, 2009 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
1996 Pontiac Grand Am Logo

Related Topics:

556 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...