Question about 1991 Ford Ranger Supercab

1 Answer

Removing manual tranny 99 ranger

A line going into the housing cannot get off

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 17 Answers

That is the hydraulic clutch line going to the internal slave cylinder.You will need to get a "clutch line removal tool" to take it out. You should be able to get one at a parts store.
Put the tool around the line and push it firmly into the bellhousing fitting and pull the line loose.

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 ranger 3.0 tranny bolt size


Autozone has free repair manuals available online.

May 11, 2013 | Cars & Trucks

1 Answer

How hard is it to replace the radiator in a 1986 Ford Ranger XL 2.9 V6? Where can I find instructions on how to do so?


This is really easy to do. There are a couple bolts to remove and two hoses to disconnect, and the two tranny lines to remove.

If yo ugo to autozone.com and register for a free account. Then login to the account. Choose vehicle year, make, and model, then choose "view repair manual"

Then pick on cooling system.

Nov 08, 2010 | 1986 Ford Ranger 2WD

1 Answer

I am putting a 99 ford explorer tranny in a 98 explorer sport with the 4.0 sohc engine. the bolts match perfect and the torque converter from the 99 tranny lines up perfect with the fly wheel. when I go to...


The torque converter is not all the way in the transmission. Pull the transmission back out(unfortunately) and you will need to shake and wiggle while lightly pushing the torque converter into the transmission. Once it goes over the splines for the pump, you will know and the space between it and the transmission housing will be minimal.

May 13, 2010 | 1998 Ford Explorer

1 Answer

99 ford won't go into reverse and makes a clunking noise this started a few days ago and all fluids are topped off.


You mean you can put it in reverse and it won't go? or the shifter won't move into the reverse position? If you're putting it in R and it won't go, then it's an internal tranny issue.

Dec 19, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Replace thermostat on 99 ford ranger with 2.5 engine


The upper radiator hose is connected between the upper radiator and the thermostat housing. Drain the coolant then remove the upper radiator hose from the thermostat housing, replace if necessary. Remove anything blocking access to the two bolts holding the housing to the engine such as the belt cover. Pay attention to the orientation of the thermostat so you install the new one correctly. If the housing is corroded or pitted you have have to replace it or suffer leaks. Push a rag into the engine opening now exposed and clean the contact surface well so it won't leak later. Installation is the reverse of the process.

Oct 12, 2009 | 1999 Ford Ranger SuperCab

3 Answers

Overdrive light flashes on and off


This will occur if the control solenoids that are located inside the pan on the valve body, are malfunctioning. First, i would check the fluid level. if the fluid level is proper, have the tranny flushed and change the filter as well. If this doesn't fix the issue, go ahead and replace the control solenoids.

Aug 24, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Need to replace clutch


Wow, your just starting..the good thing its easy. remove the shaft by taking off the UJoint from the rear end. The shaft the slides out from rear of tranny. Then remove cross member for tranny. remove shifter. Remove bolts from bell housing and your good..(PS Change slave cylinder if Manual).

Jun 16, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Torque converter removal


No, there is no other way. The tranny has to be dropped. Once it's dropped, just pull the converter from the bell housing.

Jan 30, 2009 | 1999 Oldsmobile Silhouette

1 Answer

Need step by step on how to bleed hydrolic clutch on a 1996 ford ranger


First remove the clutch reservoir top. Make sure the rubber stopper/bladder is in the cap when removed. Next locate the clutch line that goes into the tranny just aft of the bell housing. There should be a bleed screw, if so open it slightly. If no screw, than loosen the line where it attatches in. Next fill the clutch reservoir and watch till it leaks out on the tranny end. Once thats noticed, close the screw/line and recap reservoir. pump clutch pedal, and repeat bleed steps at least once more to ensure all air is out. remember to fill clutch fluid up to operating levels.

Jul 20, 2008 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
1991 Ford Ranger Supercab Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...