Question about 1995 Dodge Caravan

1 Answer

Belts how many belts does a 1995 dodge caravan have and what are the belts called

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

Depends on the engine...3.3 has 1 belt
3.0 has 2 belts a serpentine belt and an ac belt
2.5 has 3belts a waterpump belt an ac belt and a power steering belt

Posted on Nov 18, 2008

5 Suggested Answers

SOURCE: tensioner pulley 1995 dodge caravan

Hi my name is Allen!

To help you I need to know what engine you have?

For example; 3.0 liter or 3.3 liter

If it is the 3.0 liter the nut for the tensioner is toward the firewall side of the engine tucked tightly under the exhaust manifold, very hard to get too.

If its the 3.3 liter you would have already seen it, both have only one nut holding the tensioner on. This one is easier.

For further assistance contact me at FixYa!

Posted on Dec 28, 2008

RudolfDiesel
  • 100 Answers

SOURCE: replace serpentine belt on 2004 dodge caravan

Hello
Here is a link for belt replacement
RD
http://www.autozone.com/addVehicleId,2945902/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c152800b639e

Posted on Jan 15, 2009

LEFTY64
  • 69 Answers

SOURCE: Need to replace the heater core in a 1995 Dodge Grand Caravan SE

1991-95 Models

  1. Disable the air bag system by disconnecting the negative battery cable.
  2. Have the system discharged by a qualified professional mechanic using an approved recovery/recycling machine.
  3. Drain the cooling system.
  4. Remove the steering column cover and left and right side under panel silencers.
  5. Remove the center bezel by unclipping it from the instrument panel.
  6. Remove the accessory switch carrier and the heater/air conditioning control head.
  7. Remove storage bin and lower right instrument panel.
  8. Disconnect the blower motor lead under the right side of the instrument panel.
  9. Remove the right side 40-way connector wiring bracket.
  10. Remove the lower right reinforcement, body computer bracket and mid-to-lower reinforcement as an assembly.
  11. Disconnect the vacuum lines at the brake booster and water valve.
  12. Clamp off the heater hoses near the heater core and remove the hoses from the core tubes. Plug the hose ends and the core tubes to prevent spillage of coolant.
  13. If equipped with air conditioning, remove the H-valve and condensation tube.
  14. Disconnect the temperature control cable and vacuum harness at the connection at the top of the unit.
  15. Remove the retaining nuts from the package mounting studs at the firewall. Disconnect the hanger strap from the package and rotate it aside.

To install:
  1. Remove the temperature control door from the unit and clean the unit out with solvent. Lubricate the lower pivot rod and its well and install. Wrap the heater core and/or evaporator with foam tape and place in position. Secure with the screws.
  2. Assemble the unit, making sure all vacuum tubes are properly routed.
  3. Install the assembly to the vehicle and connect the vacuum harness. Install the nuts to the firewall and install the condensation tube. Fold the carpeting back into position.
  4. Connect the hanger strap from the package and rotate it aside. Install the 2 brackets supporting the lower edge of the heater housing. Connect the blower motor wiring, resistor wiring and the temperature control cable.
  5. Install the retaining screws from the right side to the steering column. Install the instrument panel trim covering and reinforcement.
  6. Assemble the unit, making sure all vacuum tubes are properly routed.
  7. Install the assembly to the vehicle and connect the vacuum harness. Install the nuts to the firewall and install the condensation tube. Fold the carpeting back into position.
  8. Connect the hanger strap from the package and rotate it aside. Connect the blower motor wiring and temperature control cable.
  9. Install the lower right reinforcement, body computer bracket and mid-to-lower reinforcement as an assembly.
  10. Install the right side 40-way connector wiring bracket.
  11. Install the lower right instrument panel and storage bin.
  12. Install the heater/air conditioning control head and accessory switch carrier.
  13. Install the center bezel to the instrument panel.
  14. Install the under panel silencers and steering column cover.
  15. Install the vacuum lines at the brake booster and water valve.
  16. Connect the heater hoses to the core tubes.
  17. Using new gaskets, install the H-valve and connect the refrigerant lines. Install the condensation tube.
  18. Have the system evacuated and recharged by a qualified professional mechanic, utilizing the proper equipment. Add 2 fl. oz. (59 ml) of refrigerant oil during the recharge. Fill the cooling system.
  19. Perform the Air Bag System Check procedures outlined in this section before connecting the negative battery cable.
  20. Connect the negative battery cable and check the entire climate control system for proper operation and leaks.

Posted on Apr 08, 2009

inspectmycar
  • 233 Answers

SOURCE: 1995 dodge caravan 3.0 L serpentine belt drive

hope

Posted on Sep 16, 2009

  • 1757 Answers

SOURCE: Need serpentine belt routing diagram for 1994 Dodge grand caravan

3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!

Posted on Jan 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a timing belt diagram for a 1995 dodge caravan 3.3


The 3.3 L Caravan engine does not use a timing belt.. It is timing chain set up. What belt are you talking about that broke?? The serpentine belt that drives all the accessories??

Jan 30, 2013 | 1995 Dodge Caravan

1 Answer

Where do I fine a diagram for the serpentine belt on a 1995 dodge caravan 3.0 L with separate belt for A\C


I come across that sometimes, a NAPA parts store are willing to print out a schematic.If not you can go to a Chrysler dealership, thell be more than happy to help.

Feb 24, 2011 | 1995 Dodge Caravan

1 Answer

Need a picture of how the belt goes on mine came off 1995 dodge caravan


When you buy the belt from Orielly's auto parts you can ask for a diagram for the routing of the belt. The belt tensioner is located near the middle of the engine towards the left. It can be adjusted by using a wrench but be careful it has a lot of tension.All you have to do is put the wrench on the center bolt and pry up or down until it moves.

Oct 08, 2010 | 1995 Dodge Grand Caravan

1 Answer

How to route the belt on a 1995 Dodge Caravan?


To find out what size your engine is, look for an emissions sticker on the hood....or look at the engine and it will be on the valve covers....

2.2L
2.5L
2.6L
3.0L OHV OR DOHC
3.3L
3.8L

May 23, 2010 | 1995 Dodge Caravan

2 Answers

2006 Dodge Gr. Caravan. Loud humming noise upon


Misalignment of the belt, incorrect belt, worn or loose tensioner, Too tight of an adjustment (many service centers do this on purpose so when the belt breaks in it becomes properly adjusted, I do not believe in this philosophy), The belt is actually one long belt called a serpentine belt.....

Feb 21, 2010 | 2006 Dodge Grand Caravan

1 Answer

Fan drive belt diagram for 1995 dodge caravan


The belt diagram should be under the hood on a white sticker. Located on the radiator cover.

Jan 20, 2010 | 1995 Dodge Caravan

1 Answer

Replace serpentine belt on 3.3 L 1995 Dodge grand


I go to the local parts store & buy a repair book for the vehicle for approx. $20, read the procedure in the book, gather the tools & parts required, replace the belt per the instructions

Oct 11, 2009 | 1995 Dodge Caravan

Not finding what you are looking for?
1995 Dodge Caravan Logo

Related Topics:

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...