Question about 1994 Mazda MX-6

1 Answer

Dash board lights out, need to replace blub. how do i do it???

How to i replace the bulbs in the dash board? Is there a way to take the panel off?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 110 Answers

Only way to replace bulbs is to remove clocks

Posted on Nov 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change dash lights in pontiac sunfire


tHE INSTRUMENT PANEL HAS NO SERVICEABLE BULBS. THE CLUSTER HAS TO BE SENT IN FOR SEVICE AS ALL THE BLUBS ARE'NT REMOVEABLE. yOUR DEALER CAN SEND IT IN FOR SERVICE AND IT COMES BACK IN ABOUT A WEEK ABOUT $175.

Oct 29, 2010 | 2003 Pontiac Sunfire

1 Answer

Installing Dash light bulbs in a 1993 S-10 Blazer


To replace the blubs you have to take out the insterment cluster. This is done by romoving the light switch trim plate and disconnect the wirering harness. The remove the A/C heater control panel. Remove the plastic trim from around the insterment cluster. The unbolt and remove the insterment cluster and uplug the wires and the speedometer cable. This speedometer cables can be a pain in the **** but depress the spring clip and pull. The bulbs are accessed from the back of the cluster.
Bulbs in this cluster don't burn out very often and if none of the bulbs don't work it probley isn't the bulbs. In this cause make sure the dimmer switch is turned up if it is play with the switch see if the dash light flicker.
Oh also in the mauals they always tell you to disconnect battery when pulling electrial apart.

Oct 20, 2010 | 1989 Chevrolet S-10 Blazer

2 Answers

Front main light wont work when new blub fitted v reg fiesta


First ensure that power is getting to the bulb connection behind the headlight. You can use a 12v test light to do this or use a known good bulb. If no power to the bulb connector, check the fuse panel on the lower left of the dash and look for the fuse for the headlight lamps and replace if necessary.

Sep 02, 2009 | 1993 Ford Festiva

1 Answer

How to replace the license plate blub


open the trunk and remove the back panel in the trunk could be a couple of clips or a few screws holding the panel on one you remove the panel you should have easy access to the bulb just twist and remove. or on some avalons you need to pry the lens off the light to replace it then the lens will click back into place with a little push

Mar 09, 2009 | 2000 Toyota Avalon

1 Answer

Light blubs in Dashboard.


Hello scooterr1105,

If you have an all digital dash, then no, there is no light bulb to replace. It is a digital device, such as that of a calculator. While I am not familiar with these types of dashes, there may be some type of element in there that merely needs replaced. My Odemeter (milieage indicator) is lighted as such as well. I haven't had any issues with it as of yet, but I imagine there may be something to replace, rather than the whole part. I would call the manufacturer, or the dealer to research this more.

Thank you for choosing fixya.com. My apologize for not having a solution for you that would fix it.

Thank you for choosing fixya.com

carsandcomps
Guru, fixya.com
Oregon

Jan 02, 2009 | 2006 Chevrolet Equinox

1 Answer

The dash board panel lights are out for the most part. The speedo is 1/2 iluminated. Could this be a fuse ? If not, how involved is it to change the lights?


i think it could be bulb issue.

you have to remove the dash board and replace bulbs that are busted. replacing the bulb is no problem . the problem is taking the dash off. need to remove the dash cover first before you can remove the actual dash.

another thing to consider is the speedometer cable which is attached at the center of the gauge.

tnx 4 using fixya,

drcool

Oct 28, 2008 | 2006 Toyota Sequoia

1 Answer

Colorado Instrument panel lighting


The bulbs plug into a printed circuit board, I suspect they have come loose, pull the cluster and see if they are loose or burned out.

Oct 26, 2008 | 2006 Chevrolet Colorado

1 Answer

1990 Buick Lesabre Custom


You will need to include more information. !. Are you referring to the turn blub in the dash or the bluds mounted in the body of the car. If in the body of the car, you need to indicate whether it is front or rear.?

If the rear, open the trunk, and in the corner nearest the tail light you will see a cloth like material that can be pulled back, which will uncover the tail light assembly. From there you can remove the blub and holder by turning it to the left or right, pull it out and remove the blub.
Bill

Oct 25, 2008 | 1992 Buick LeSabre

1 Answer

Replace light blub in the infromation center on dash


after disassembly of dash and unit is away from dahboard enough to see. you will see fiber optic wires that go into one cluster. the could be white or black. it has one light bulb in that cluster it will twist out for replacement.

Oct 12, 2008 | 1998 Plymouth Voyager

Not finding what you are looking for?
1994 Mazda MX-6 Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...