Question about Dodge Durango

1 Answer

My problem of my truck light all of them is keep flashing like emergency light.After 10 minutes showing the problem when i turn it on the ignition switch.

Posted by on

  • Rabindra Robinson May 11, 2010

    can you be more specific please

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 393 Answers

Be sure the hazard switch isn't depressed i had same truck it easy to hit by accident

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could keep my coil from firing ? I have the Ignition control signal and 12v. while cranking over engine at the top primary wiring of coil. Can you help me get spark?


Sounds like the security system is causing your problem. Is the "security" light flashing? If it is, turn the key on, leave the key in the ON position for 10 minutes. The light will stop flashing. Now, turn OFF the key, turn it back to ON, and then crank it. It should start. If the security light starts flashing again, go through the process again until it starts. This is resetting the security system after the battery has died, battery has been changed, radio was changed, instrument cluster was removed and replaced, etc. Hope this works for you.

Mar 29, 2016 | 2001 Chevrolet Silverado 1500

1 Answer

What does a car with a lock light mean


Chevrolet Malibu Questions - SECURITY SYSTEM LIGHT ...

www.cargurus.com > Questions > Chevrolet > Malibu

CarGurusFeb 3, 2014 - SECURITY SYSTEM LIGHT COMES ON - CAR TURNS OVER WON[T START ... Insert the ignition key into the driver door lock. ... When I start my car 3 keys programmed pops up on my dashboard what does that mean.

Chevrolet Malibu Questions - Why does the anti theft system ...

www.cargurus.com > Questions > Chevrolet > Malibu

CarGurusFeb 23, 2011 - Why does the anti theft system keep tripping on my 03 malibu - Every other day my anti-theft system goes off in my car then I have to reset it. It's not ha... ...it needs a pass lock sensor/ ignition lock cylinder. 10 out of 10 people think ... Wait 10 minutes until the light stops flashing, then start. Repairs could run ...

No Start Due to Failed Passlock Sensor : Chevrolet Malibu ...

repairpal.com > Problems > Chevrolet > Malibu

Jan 13, 2016 | 2005 Chevrolet Malibu Maxx

1 Answer

97 cavalier cranks will not start theft light stays on


Is the security light flashing? If so, turn ignition on and wait for 10 minutes and light should stay on solid. Then try and start the car without turning the ignition back off. Then turn off ignition and wait 1 minute. Then turn ignition on and see if security light is flashing. If not try and start your car. If it is flashing, try waiting again with just the ignition on and see if it goes out.

Nov 24, 2012 | Cars & Trucks

1 Answer

I have a 2001 Oldsmobile Alero. A month ago I did have the ignition replaced in it to the tune of $795. I got in my car today, and it turns, starts then shuts off after about two seconds. It does...


It still sounds like a passkey or theft deterrent issue. The check engine light is most likely a B2865 or B2860 code for an invalid key, likely related to the ignition switch being replaced. The passlock sensor is inside the ignition switch, and could have been damaged during install. Try just turning the key on and watch the security light, if it starts to flash after a few minutes, keep the key on for 10 minutes (or until it stops flashing). Then retry to start. You may have to have it scanned for further diagnosis.

Feb 22, 2011 | 2001 Oldsmobile Alero

4 Answers

Security light keeps going on, I'm not able to start it then... how do I disable this?


IF YOU AWAY FROM HOME. LIKE AT WORK, SHOPPING MALL OR STORE.WHEN YOU GET IN CAR AND IT DONT CRANK.PUT KEY IN THE IGNITION SWITCH AND TURN IGNITION SWITCH TO THE ON POSITION FOR 10 MINUTE.UNTIL YOU SEE THE SECURITY LIGHT TURN OFF. WHEN SECURITY LIGHT TURN OFF TURN OFF IGNITION SWITCH WAIT FOR 5 SECONDS. THEN TRY STARTING VECHICLE SHOULD START.TAKE VECHICLE TO DEALERSHIP.THEY WILL HAVE SCAN VECHICLE.YOUR PROBLEM COULD BE WORN IGNITION KEYS OR WORN IGNITION SWITCH ALSO FAULTY BCM.THE DEALERSHIP HAS TO FIX AND REPROGRAM THEFT SECURITY SYSTEM.IF YOU REPLACE KEYS, IGNITION SWITCH OR BCM. THE 10 MINUTE TRICK WILL GET CAR STARTED TO GET HOME OR SHOP.BUT DONT KEEP DRIVING BECAUSE IT WILL COME TO A POINT WHERE VECHICLE WONT CRANK AGAIN.

Nov 20, 2010 | 1999 Oldsmobile Alero

1 Answer

Purchased a new clicker.from g/m.i can't program it.i have replaced the transformer under the dash panel that was used.. i have been told 96 models has several transmitters on it.


1. Move all Keyless Remotes out of range of vehicle. (10 to 15 feet)
2. Turn ignition key to the ON position.
3. Push the TRIP/ODO button on the DIC (Driver Info Center) twice.
4. Within 5 seconds, push & hold the FUEL INFO button on the DIC until
the PKE light comes on and stays on.
5. Turn the ignition to the OFF position, but leave the key in the ignition.
The PKE light will begin flashing.
6. Bring one Keyless Remote into range. The PKE light will stop flashing
and stay on to show the code is stored. Move the Keyless Remote out
of range. The PKE light will begin flashing indicating the system is ready
for the next Keyless Remote.
7. If more than one Keyless Remote is being programmed, move the first
Keyless Remote out of range and repeat step 6 for any additional Keyless
Remotes. Up to three Keyless Remotes can be programmed.
8. To turn off the programming mode, simply remove the key from the ignition
or turn the ignition switch on.
9. The programming mode will shut off after two minutes if.
A) You have not programmed any Keyless Remotes.
B) Removed the key from the ignition.
C) After three Keyless Remotes have been programmed.

Good luck and keep me posted.

Jan 23, 2010 | 1996 Chevrolet Corvette

2 Answers

My car turns over like it wants to start but never connects. Also the security light came on yesterday and this never happens. What could be wrong?


 If you have the second ignition key's with you try it.  If not try this, it takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself. Good luck and hope this helps, keep me posted, be glad to help. 

Jul 20, 2009 | 2001 Pontiac Grand Am SE

2 Answers

1996 Oldsmobile Achieva: Security light flashes upon startup


Here is what you do, but only when the SECURITY light flashes - if it is always ON or OFF it's no use.
Turn the key in the ignition to ON.
Wait for exactly 10 minutes ( SECURITY light will flash for 10 minutes and then stay on SOLID)
Turn the key to OFF
Wait 5 seconds.
Turn the key in the ignition to ON.
Wait for exactly 10 minutes.
Turn the key to OFF
Wait 5 seconds.
Turn the key in the ignition to ON.
Wait for exactly 10 minutes.
Turn the ignition OFF.

Start the car normally.
It has relearnt the keycode and you're good to go.
NOTICE - it takes 30 minutes to relearn, that's THREE cycles of ON - 10 minutes - OFF.

Good luck.

Jul 11, 2009 | 1996 Oldsmobile Achieva

1 Answer

When security light flashing,will not allow car to start,why??


Because you have to let the system relearn the keys for some reason. Its a pain in the nack but do this:
Turn key in the ignition to ON
Wait for 10 minutes.
Turn it OFF
wait for 5 seconds.
Turn key in the ignition to ON
Wait for 10 minutes.
Turn it OFF
wait for 5 seconds.
Turn key in the ignition to ON
Wait for 10 minutes.
Turn it OFF
wait for 5 seconds.

Start the car as you would normally.

Good luck.

Jul 11, 2009 | 1999 Oldsmobile Alero

1 Answer

Security light flashing and ignition doesnt work


your ignition switch is bad for now though turn your key on for at least ten minutes until the light stops flashing this will reset your security system after stops flashing turn key off and then start the truck

Mar 17, 2009 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...