Question about Plymouth Voyager

1 Answer

Whenever i put the voyager on driveshift and press on the pedal,it turn off the engine

Posted by on

  • dunmart Nov 15, 2008

    the engine turn off without moving whenevr i press the pedal to move the vehicle

  • yadayada
    yadayada May 11, 2010

    What is the question in this sentence?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 21,949 Answers

Engine cutting out when accelerating??if so see a local mechanic as their is a number of reasons and without a computor diagnostic connected it difficult to advise

Posted on Nov 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How toprogramm car key toyota matrix


  • 1 First you will need to purchase a blank Toyota transponder key. You can do this from the dealership, a locksmith, or an online source such as eBay. Once you have the key, take the blank key and the master key to a locksmith that he or she can duplicate the key. This will be much cheaper than the dealership.
  • 2 Now that you have the newly cut key and the master key, you can program the Toyota transponder key. Sit in the driver's side of the Toyota vehicle. Press and release the brake and gas pedal simultaneously.
  • 3 Insert the master transponder key. Do not turn it. Push and release the gas pedal 5 times within at least 15 seconds of inserting the master key.
  • 4 Press and release the brake pedal 6 times within 20 seconds of completing step 3, then remove the master transponder key.
  • 5 Insert the newly cut transponder key into the ignition, but do not turn. Press the gas pedal once.
  • 6 Wait up to 2 minutes or whenever the security light on the dashboard turns off. Once the light goes off, remove the new transponder key and press the brake pedal once. The new transponder key should now be programmed. Test the key by attempting to start the engine. If the engine does not start, repeat the steps above.
  • Mar 02, 2015 | 2010 Toyota Matrix

    1 Answer

    Press gas pedal


    check your throttle pedal position switch and your throttle position sensor

    Dec 19, 2013 | 2005 Chevrolet Cobalt Sedan

    1 Answer

    96 voyager is very weak in power. when you press the gas pedal the engine starts missing and just about stalls


    When was last tune-up ? Did this start suddenly? Any "check engine" light on in dash? Has fuel pressure been checked?

    Jan 23, 2013 | 1996 Plymouth Voyager

    1 Answer

    Hard brake pedal, 1997 grand voyager


    You likely have a defective power assist power brake booster, have a brake shop confirm this for you.

    Jun 16, 2012 | 1997 Plymouth Grand Voyager

    1 Answer

    1991toyotapickup clutchrepair manual


    ther is not any clutch repair manual i give some idias put your car on safety jack stands drain ****** oil remove driveshift or cardan you have to remove the clucth pump remove starter remove like 8 bolts of the ****** remove ****** mount remove ****** when you remove like 8 bolts in the clutch plate check very well their position or get pictures when your done push your cluch pedal few times WARNING if you never didnt any of this type of jobes dont doit only if you have some experience safety better good luck

    Jan 15, 2012 | 1991 Toyota Pickup

    1 Answer

    96 plymouth grand voyager is stuck on park what does that mean?


    Your problem might be with the brake light switch. This switch is under the brake pedal, and when the pedal is pressed, it lets you shift your van out of park. This switch also activates the brake lights when you press the brake pedal. Try checking if your brake lights work. These switches are inexpensive, and very easy to replace.
    Matt

    Jun 15, 2011 | 1996 Plymouth Grand Voyager

    2 Answers

    I have a 99 Plymouth voyager 3.3 flex fuel which stalls constantly on initial take off only. had the crank sensor replaced twice. was previously getting po140 code which is o2 sensor which i havent...


    Check the engine mounts. A friend of mine had a similar problem whereas acceleration caused a stall because the engine was rocking out of position.

    Jul 27, 2010 | 1998 Plymouth Voyager

    1 Answer

    Starts then shuts off


    if you give it some gas pedal while you start it, will that help it. there is a thing call an idle control solenoid. this allow a little air in to the engine while sitting with no throttle.

    Jun 30, 2009 | 1998 Plymouth Grand Voyager

    2 Answers

    94 Plymouth Voyager ABS light stays on


    Had a similar problem a number of years back. Underneath the brake pedal arm is a small switch with a plunger. when you press the pedal down it moves the plunger in and engages the brake lights. when you let off it's supposed to pop back out (turning the lights back off). Possible it is getting stuck in the down position and could need to be replaced. very easy to install and only about an 8 dollar fix.

    Mar 09, 2009 | Plymouth Voyager Cars & Trucks

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    42 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Plymouth Experts

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Plymouth Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...