Question about Ford Windstar

1 Answer

I have a 97 ford windstar that keeps blowing the fuse for the speedodemeter ,odemeter and the brake light and ABS light comes on when blowen.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 22,041 Answers

Dodgy light cluster on rear lights check connectors and bulbs

Posted on Nov 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My ABS light is on and the ABS keeps going off when I push my brakes. Can I just change the ABS fuse to start? I didn't want to take it to a mecanic to be charged $50. to check it out only to find out it's...


You should pay about $80.00 to diagnose the ABS System failure
More to repair if there is a problem

Fuses don't fix anything
Fuses don't get bad
Fuses protect circuits, from overheating, due to high current loads or a short to ground.
If a fuse blows,replacing it, just cause another to blow,until problem is corrected

Oct 07, 2010 | 2000 Ford Windstar

2 Answers

Can i bypass the abs system on my 98 ford windstar


Are you wanting to discontinue the abs? If so, then keep in mind that you will no longer have abs. The brakes will still function the same without abs. In order to "bypass" the abs system, locate the main fuse/control box under hood. There should be either a relay or large fuse marked for abs. If so, simply remove the fuse/relay.

Jun 09, 2010 | 1998 Ford Windstar

2 Answers

99 Ford windstar ABS light coming on and blowing fuse under dash. The problem is that the fuse also works the speedometer! Please help: where is the abs mod? and how can i fix this. Thank for any help!


Check the connector at the ABS unit. There have been some problems where the brake pressure switch leaks, the brake fluid runs down the wires right to the ABS connector, and creates a short. If this is the case, you'll have to replace the pressure switch kit and the ABS connector.

Sep 17, 2009 | 1999 Ford Windstar

1 Answer

Which fuse is the on that controls the problem, No manual when bo


speed odo is blank and o/d flashes and abs and brake light is on

Aug 13, 2009 | 2001 Ford Windstar

1 Answer

Brakes and fuse


did you replace and/or resurface the rotors??
a warped rotor will cause vibration and/or pulsating in the pedal!!
fuse # 16 is for cigar lighter/ flasher relays!!

Jun 17, 2009 | 1997 Ford Crown Victoria

2 Answers

2000 ford windstar... electrical mess!!


one reason for that fuse to blow is a bad brake pressure switch on the master cylinder. could be a
warranty/recall item. can also leak brake fluid. also check behind each wheel for any sign of brake fluid,
particularly the rear wheels if you have rear drum brakes. fixed one here recently where the vehicle's jack
came loose in the right rear compartment and short that circuit. make sure your jack is stowed properly.

good luck

Jun 17, 2009 | 2000 Ford Windstar

3 Answers

Brake switch fuse keeps blowing


replace your brake pressure switch on the master cylinder and that should take care of your problem.

Jun 04, 2009 | 1997 Ford F150 Regular Cab

4 Answers

Blown fuses


The problem is simple and you could possibly repair it yourself. the sensor on the brake master cylinder (front side protruding down from the bottom) is shorted out. This sensor turns off the cruise control when the brakes are pushed. You only have to unscrew the old sensor and replace it with the new one. You will notice that the old sensor has has brake fluid all through out it. this is the reason for the short. BTW you will lose a little brake fluid in the process so have the new sensor ready when you take off the old sensor. I know this doesnt sound like it could possibly be the reason but it is. hope it helps

Jul 17, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...