Question about 1996 Chevrolet Blazer

1 Answer



Posted by on

  • 1 more comment 
  • Anonymous Dec 03, 2008

    My brake lights and hazard flashers stopped working. Directionals and taillights are OK

  • Anonymous Mar 16, 2014

    tail lights don't works. brake lights,and signals don't work at night.

  • Anonymous Mar 21, 2014

    turn off hazard light



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert that has over 500 points.

  • Expert
  • 324 Answers

Did you check the fuses?

If so, then check the plug on the steering column....

Posted on Nov 26, 2008


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 11896 Answers

SOURCE: 97 blazer hazards, turn signals and tail lights

Likely the brake switch above brake pedal is bad.

Posted on Feb 10, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 97 blazer. My turn signals don't work...not even on the hazard lights...and brake lights are on without pressing the pedal...what can I do

this could be the signal switch that has shorted out or damaged. unplug the switch, this is down at the base of the steering colume, check for poor connections. with the switch connected, using a test light turning on the signals check for power at the connector. yellow is left signal, green is right signal. if you don`t have power at this spot the switch is bad.

Apr 09, 2015 | 1997 Chevrolet Blazer

2 Answers

I have a 1989 ford f250 my hazard lights and brake lights don't work but my turn signal and tail lights do what could it be

Hi Jonathan,

I am not positive, but believe your Hazards work on the 'high' element of your tail lights, similar to how your brake lights do. Recall, when your lights are on, your brake lights are at normal illumination; when you press on the brakes, they're on their 'high' mode. If these high elements are burnt out, they won't illuminate; and accordingly neither may your hazards. Again, not certain on the hazards using the high element, but think so.

Good luck.

Feb 26, 2015 | Ford Cars & Trucks

1 Answer

1991 Park avenue, Tail lights and license's plate light's stopped working turn signal's hazards and brake lights still functional. but no tail lights or license plate lights

Check for Power on your License Plate Light, more than likely you have lost GROUND

Turn Signals, Do the Front Work and the Back don't? If NONE then FLASHER FUSE

Apr 09, 2013 | 1991 Buick Park Avenue

1 Answer

Rear lights not working on 2002 suzuki grand vitara

In the underdash fuse/relay box, the 15A TAIL fuse feeds power to the coil of headlight relay 2. When the combination switch is set to TAIL, the relay closes and the outer tail lamps light. In the same underdash fuse/relay box, the 20A STOP fuse feeds power to the brake light switch. When the brake pedal is pressed, the inner brake lamps light. The underdash fuse/relay box also contains the 10A TURN BACK fuse which feeds power to the hazard switch and the turn signal relay. Relay output is fed to the combination switch and turn signal power is applied to the selected middle tail light. The fourth fuse in the underdash fuse/relay box is the 15A HAZARD fuse which feeds power to the hazard switch and turn signal relay. When the hazard switch is set, the turn lamps on both sides begin flashing.

Sep 18, 2012 | 2002 Suzuki Grand Vitara

1 Answer

97 blazer all three brake lights dont work and also the hazard,but the parking lights and turn signals work fine.when you push the pedal you hear a noise down there

Hi, Sounds like you have a short in wiring, also check the brake fuses. Have it checked out by a (qualified mechanic).

Jun 07, 2011 | 1997 Chevrolet Blazer

2 Answers

My 97 chevy blazer, the brake lights dont work but the third brake light does and the turn signals or hazard lights dont work??

More likely it is the hazard/turnsignal/highbeam/cruise control switch module. It costs about $275 for the module. However there is a repair kit for the likely culprit...the hazard button. Try jiggling it around a little, see if that helps. Spray a little WD-40 into it so it can jostle back into it's correct position. You could try a junkyard unit or Ebay. It's not too hard to change. The hard part is doing it without removing the steering wheel. It can be done. I've done it. But hopefully you can locate the repair kit which costs about 15 dollars. Good luck.

Apr 27, 2010 | 1997 Chevrolet Blazer

1 Answer

Problem with my 97 Chevrolet S10 Blazer

I'd look into the multifunction switch. That controles both hazard and turn.

Dec 12, 2009 | 1997 Chevrolet Blazer

1 Answer

Left side brake and hazard lights don"t work

sounds like a bad turn signal switch, wiggle it , just a little bit,... see if some of the lights start to work. do your turn lights work correctly??

Dec 02, 2008 | 2000 Chevrolet Lumina

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

Related Topics:

507 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78010 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides