Question about 2004 Jaguar X-Type

1 Answer

Steering wheel removal

How to I remove the steering wheel from my 2006 X type - worried about the air bag ?

Posted by on

  • Anonymous Mar 16, 2014

    Remove sterring wheel only

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 324 Answers

First you want to unplug the air bag. you do this buy removing the plastic surround around the steering column, where the ignition is, just below the steering wheel itself, then you have to remove the air bag by removing the bolts from the back of the steering wheel...

then get a steeering wheel removal kit, autozone has a loan a tool program.

put the steering wheel tool on and turn oit with a wrench adn the wheel will pop off...

Posted on Nov 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steering wheel airbag removal on 2006 Cadillac cts cant find bolts


There are no bolts ! it takes a special tool , there are spring loaded Fasteners .
Pull the handle of the air bag tool away from the instrument panel (I/P) releasing one of the spring loaded fasteners.
Steering Wheel Inflatable Restraint Module Replacement
Tools Required J 44298 Driver Air Bag Removal Tool
Removal Procedure
Caution: Refer to
SIR Inflator Module Handling and Storage Caution in the Preface section.
Caution: Refer to SIR Caution in the Preface section.

showgif.do?image=640349

tif.gif
Caution: A deployed dual stage inflator module will look the same whether one or both stages were used. Always assume a deployed dual stage inflator module has an active stage 2. Improper handling or servicing can activate the inflator module and cause personal injury.
  1. Disable the SIR system. Refer to SIR Disabling and Enabling .
  2. On the back side of the steering wheel are 3 openings for removing the steering wheel module.
  3. Adjust and install J 44298 into 1 of the holes.
  4. Important: Seat the air bag removal tool all the way in to perform properly.
  5. Pull the handle of the air bag tool away from the instrument panel (I/P) releasing one of the spring loaded fasteners.
  6. Repeat this step for the other 2 fasteners.
  7. Pull the inflatable restraint module gently away from the steering wheel.
    showgif.do?image=818476
  8. tif.gif
  9. Important: Note the wire routing positions on the steering wheel module connectors, the redundant control routing positions, and the horn wire routing positions for the correct assembly.
  10. Remove the connector position assurance (CPA) (4) and the electrical connector from the steering wheel module.
  11. Remove the horn contact lead (2) from the steering column cam tower.
  12. Remove the steering wheel module (5

Mar 09, 2015 | 2006 Cadillac CTS

1 Answer

Remove the steering wheel of a 2013 Toyota corolla


As a general thing on newer models, disconnect negative battery cable, pull the air bag fuse(s) to ensure the air bag doesn't deploy. Remove the air bag by taking out the attaching screws usually on the back side of the wheel. Disconnect the air bag wiring from bag assembly then from steering column, unbolt wiring assembly and remove. Unscrew center hub bolt, then use a wheel puller to remove wheel.

May 23, 2014 | Toyota Corolla Cars & Trucks

1 Answer

Airbag light is on horn is not working what to do


Hi, odds are your clockspring has broken. You'll have to remove the steering wheel to access the clockspring, which will require the use of a steering wheel puller. I have pasted procedures below from autozone.com. After removing the airbag and before removing the steering wheel, you can verify that the clockspring has failed, if desired, by testing the continuity of the wires from the airbag to the bottom of the steering column. Please let me know if you have any questions, and thanks for using FixYa.
Removal & Installation CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the steering wheel. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

1. Make sure the front wheels are in the straight-ahead position.

2. Turn the ignition key cylinder to the LOCK position and remove the key. Turn the steering wheel a half turn toward the left until the steering column becomes locked in position.

3. Remove the 3 bolts attaching the air bag module to the steering wheel. Remove the air bag module.


CAUTION Disconnect and isolate the negative (ground) battery cable. Allow the system capacitor to discharge for at least 2 minutes before continuing with the removal procedure. This will disable the air bag system.

jturcotte_466.jpgFig. The airbag is attached to the steering wheel by three fasteners

jturcotte_467.jpg
Fig. After the airbag is unbolted from the steering wheel . . .

jturcotte_468.jpg
Fig. . . . reach behind and unplug the electrical connections

4. Disconnect the wiring connectors from the air bag module, horn switch and speed control switches.

5. Remove the routing clip for the wiring harness from the air bag module studs.

6. Remove the steering wheel mounting nut from the steering column shaft and remove the steering wheel damper from the steering wheel.

jturcotte_469.jpg
Fig. Always hold the airba
g away from your body when transporting it to a storage area

jturcotte_471.jpg
Fig. With the airbag removed, the steering wheel retaining nut can be removed

jturcotte_472.jpg
Fig. After the nut is removed, set aside the damper plate . . .

jturcotte_473.jpg
Fig. . . . and use a paint marker to matchmark the steering wheel shaft with the wheel

7. Using a steering wheel puller tool, remove the steering wheel from the steering column shaft. Do not thread the steering wheel puller tool bolts into the steering wheel more than a 1/2 in. or damage to the SRS clockspring will result. Do not hammer or bump the steering column or shaft when removing the steering wheel
8. Remove and replace the clockspring.

jturcotte_470.jpg
Fig. A steering wheel puller must be used to remove the wheel from the shaft

jturcotte_474.jpg
Fig. Once the wheel is free of the shaft, carefully route the wires through the wheel

To install:
1. Before installing the steering wheel, the clockspring must be centered . Center the clockspring as follows:
a. Disengage the lock mechanism by depressing the 2 plastic locking pins.

b. Turn the clockspring rotor clockwise until it stops, while the lock mechanism is disengaged. Do not use excessive force.

c. From the end of the clockwise travel, turn the clockspring rotor counter-clockwise. The clockspring wires should be at the top. Engage the clockspring locking pins.

d. Turn the clockspring a 1/2 additional rotation counter-clockwise from the center locked position. This should put the clockspring wiring at the bottom.

e. The clockspring is now correctly positioned for installation of the steering wheel.


2. Install the steering wheel onto the steering column shaft. Make sure the master splines of the steering wheel and steering shaft are in correct alignment. Be sure the flats on the steering wheel align with the formations on the clockspring. All wiring leads from the clockspring must be routed correctly.

3. Install the steering wheel damper onto the steering wheel in its original position.

4.Install the steering wheel-to-steering shaft retaining nut. Torque the retaining nut to 45 ft. lbs. (61 Nm).

5. Reconnect the horn switch wiring lead from the clockspring, onto the steering wheel horn switch wiring.

6. If equipped with speed control, reconnect the speed control wiring from the clockspring onto the speed control switch.

7. Install the wiring lead from the clockspring onto the air bag module. Make the wiring connection onto the air bag module, by pressing straight in on the connector. Be sure it is fully seated.

8. Install the air bag module to the steering wheel and then install the 3 air bag module attaching nuts. Torque all 3 air bag module attaching nuts to 100 inch lbs. (11 Nm).

9. When reconnecting the battery on a vehicle that has had the air bag removed, the following procedure should be used:
a. Connect the DRB or equivalent scan tool, to the ASDM diagnostic 6-way connector.
b. Turn the ignition key to the ON position. Exit the vehicle with the DRB, and install the latest version of the proper diagnostic cartridge into the DRB.
c. Make sure there are no occupants in the vehicle and reconnect the negative battery cable.
d. Using the DRB, read and record active or stored fault codes. Take appropriate actions to correct any faults.
e. Erase stored fault codes. If problems remain, fault codes will not erase.
f. From the passenger side of the vehicle, turn the ignition key to OFF and then ON , observing the instrument cluster air bag lamp. It should go ON for 6-8 seconds, then go out. This will indicate that the air bag system is functioning normally.


WARNING If the air bag warning lamp fails to light, blinks ON and OFF or goes ON and stays ON, there is an air bag system malfunction.

g.
Test the operation of any steering column functions such as the horn, lights or speed control system.
h.
Road test vehicle. Be sure the speed control and steering systems are functioning properly

Apr 24, 2011 | 2000 Chrysler Grand Voyager

1 Answer

I need to put in another steering collum and I dont know how to do it.its a 91 ford F150.hope you can help me.I got another one out of the junk yard for 125,00 is that a good price .thanks for helping my...


I'd say $125.00 is a good price for a steering column.

First, have to remove steering wheel (but I don't have instructions for the steering column. For that, maybe try alldata.com, but that will cost):

STEERING Steering Wheel REMOVAL & INSTALLATION Without Air Bag EXCEPT F-SUPER DUTY STRIPPED CHASSIS MODELS AND MOTOR HOME CHASSIS MODELS Fig. 1: Remove the screws from behind the wheel - F-150 model without air bag 88288p12.jpg
Fig. 2: Pull away the cover with the wiring still connected 88288p13.jpg
Fig. 3: Disconnect the wiring at the steering wheel 88288p14.jpg
Fig. 4: Matchmark the steering wheel 88288p15.jpg
Fig. 5: Remove the center nut from the steering wheel 88288p16.jpg
Fig. 6: Use a steering wheel puller to remove the wheel 88288p17.jpg
Fig. 7: Remove the steering wheel from the shaft 88288p18.jpg
Fig. 8: Correct steering wheel installation 84928058.gif
NOTE: The factory recommends that the front wheels be set in the straight-ahead position and you paint or make chalk marks on the column and steering wheel hub for alignment purposes during installation. Of these two safeguards, it is more important to mark the column so even if the column is moved slightly, the steering wheel can still be repositioned in its original position.
  1. Disconnect the negative battery cable.
  2. Remove the one screw from the underside of each steering wheel spoke, and lift the horn switch assembly (steering wheel pad) from the steering wheel. On vehicles equipped with the sport steering wheel option, pry the button cover off with a suitable prytool.
  3. Disconnect the horn switch wires at the connector and remove the switch assembly. On trucks equipped with speed control, squeeze the J-clip ground wire terminal firmly and pull it out of the hole in the steering wheel. Don't pull the wire out without squeezing the clip.
  4. Remove the horn switch assembly.
  5. Remove the steering wheel retaining nut and remove the steering wheel with a puller. WARNING
    Never hammer on the wheel or shaft to remove it! Never use a knock-off type puller.
  6. Install the steering wheel in the reverse order of removal. Tighten the shaft nut to 40 ft. lbs. (54 Nm)
F-SUPER DUTY STRIPPED CHASSIS MOTOR HOME CHASSIS MODELS
  1. Set the front wheel in the straight-ahead position and make chalk marks on the column and steering wheel hub for alignment purposes during installation.
  2. Disconnect the negative battery cable.
  3. Remove the one screw from the underside of each steering wheel spoke, and lift the horn switch assembly (steering wheel pad) from the steering wheel.
  4. Disconnect the horn switch wires at the connector and remove the switch assembly.
  5. Remove the horn switch assembly.
  6. Remove the steering wheel retaining nut and remove the steering wheel with a puller. WARNING
    Never hammer on the wheel or shaft to remove it! Never use a knock-off type puller.
  7. Install the steering wheel in the reverse order of removal. Tighten the shaft nut to 30-42 ft. lbs. (41-57 Nm).
With Air Bag Fig. 9: Remove the air bag module and disconnect the wiring harnesses 88288g00.gif
CAUTION
Read the air bag service precautions in Section 6 prior to doing work involving an air bag equipped steering column component. Always wear safety glasses when servicing an air bag vehicle and handling the air bag to avoid possible injury.
  1. Turn the front wheels to the straight-ahead position.
  2. Disconnect the battery-to-starter relay cable for at least one minute to let the air bag back-up power supply discharge.
  3. Remove the air bag module from the steering wheel (refer to Section 6).
  4. Disconnect the horn/speed control wiring from the steering wheel.
  5. Remove the steering wheel retaining bolt.
  6. Install the Differential Bearing Cone Remover/Replacer, No. T77F-4220B1, or equivalent, and remove the steering wheel. Route the contact assembly harnesses through the steering wheel as it is lifted off of the shaft. To install: NOTE: Make sure the front wheels are still in the straight-ahead position prior to installation.
  7. Route the air bag sliding contact wiring through the steering wheel at the 3 o'clock position. Position the steering wheel on the shaft an align the marks. Make sure not to pinch the contact wire. WARNING
    Make sure no air gets trapped between the steering wheel and air bag sliding contact.
  8. Install a new steering wheel retaining bolt, then tighten to 23-33 ft. lbs. (31-45 Nm).
  9. Connect the horn/speed control wiring and clip in place. Connect the air bag wire harness. Tighten the module retaining nuts to 35-53 inch lbs. (4-6 Nm). NOTE: When the battery cable has been disconnected, then reconnected, some abnormal driving symptoms may occur for the first 10 miles (16 km) until the PCM re-learns it adaptive strategy.
  10. Connect the battery to starter cable. Verify the air bag warning indicator light on the instrument panel.
prev.gif next.gif

Sep 24, 2010 | 1991 Ford F150

1 Answer

How do I replace steering wheel on 1995 chevy 1/2 ton pickup? will air bag deploy on me?


Well first disconnect the positive side of the battery. Then I recommend grounding the positive battery cable to the frame or negative side of the battery. (This will insure you have all possible stored voltage removed from your system). Your 95 model has two types of steering wheels and air bags. Model 1 there are four holes in the back of the steering wheel. You simply push a small punch or ice pick in the center to release the airbag from the steering wheel. If you have the later model 1995, there is a slot and you have to push a wire clip that holds the bag to the steering wheel. Once you get the air bag off the wheel, it just unplugs and you remove the steering wheel using a puller. All GM air bag circuits are yellow. They won't deploy without power. Good luck, I hope this helps.

Mar 13, 2010 | 1995 Chevrolet C1500

1 Answer

Needs key cylinder replacement


This first post is WITH AN AIR BAG:



With Air Bag Before removing the steering wheel, disable the air bag system
Disarming the System To disarm the air bag system, simply disconnect the negative battery cable from the battery. Isolate the battery cable by taping up any exposed metal areas of the cable. This will keep the cable from accidentally contacting the battery and causing deployment of the air bag. Allow the system capacitor to discharge for at least 2 minutes, although 10 minutes is recommended, to allow for the dissipation of any residual energy.

CAUTION Before removing the steering wheel, disable the air bag system (refer to Section 6). Failure to do so could result in accidental air bag deployment and possible injury.


  1. Disconnect the negative battery cable and disable the air bag system.
  2. Set the front tires in a straight-ahead position.
c0447ef.gif
Exploded view of the air bag module mounting

  1. Remove the air bag module retaining nuts from behind the steering wheel.
  2. Remove the air bag module.
  3. If equipped, remove the cruise control switch.
  4. Disconnect the horn wiring.
  5. Remove the steering wheel retaining nut.
  6. Scribe a line mark on the steering wheel and steering shaft if there is not one already.
1c64d39.gif
Use a puller to separate the wheel from the column

  1. Remove the steering wheel using a suitable puller.
To install:
  1. To install, align the scribe marks on the steering shaft with the steering wheel.
  2. Ensure the wheel compresses the 2 locktabs on the clockspring.

Oct 11, 2009 | 1993 Jeep Grand Cherokee

1 Answer

How do you get the steering wheel off a land rover discovery 3


with great difficulty,first you have to disconnect battery to stop air bag accidently going off ,then remove the air bab ,two clips underneath steering wheel ,very difficult without the right tools ,then the big nut and maybe evan a steering wheel puller.Whats the fault that necessatates removing the steering wheel in the first place?

Sep 10, 2009 | 2006 Land Rover LR3

1 Answer

Replacing a Cruise Control Switch


Ford Taurus/Sable 1996-1999 Repair Guide
Steering Wheel
Removal & Instalation

e69ab1a.gif

Fig. 1: Remove the access covers for the air bag module retaining bolts

83ac520.gif

Fig. 2: Remove the air bag retaining bolts and...

d0a0934.gif

Fig. 3: Carefully remove the air bag from the steering wheel to access the wiring connectors

3344f1a.gif

Fig. 4: Detach the connectors...

12ea02c.gif

Fig. 5: ... from the air bag module

6e8ff5b.gif

Fig. 6: Remove the center bolt from the steering wheel

fef72e6.gif

Fig. 7: Install a suitable puller and tighten the forcing screw to...

4b45cbd.gif

Fig. 8: ... remove the steering wheel


CONTINUE...

Aug 19, 2009 | 1998 Ford Taurus

2 Answers

97 Nissan Quest - steering wheel buttons don't work


probably the clock spring uner the steering wheel. It transfers voltage from the steering column to the steering wheel.

Section 11-04: Steering Column 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Sliding Contact, Air Bag Removal
  1. svv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE BACKUP POWER SUPPLY ENERGY MUST BE DEPLETED BEFORE ANY AIR BAG COMPONENT SERVICE IS PERFORMED. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE (14301) AND WAIT TEN MINUTES.
    Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Match mark and tape in place the inner and outer elements of the air bag sliding contact.
  1. Remove the two steering column shroud screws and the lower steering column shroud (3530).
  1. Loosen the shifter boot and position the upper steering column shroud out of the way.




  1. Remove the three air bag sliding contact screws.




    230e052.gif





  1. Disconnect the two lower air bag sliding contact electrical connectors.
  1. Remove the air bag sliding contact from the vehicle.

Apr 27, 2009 | 1997 Nissan Quest

2 Answers

Upgrade 97 Lexus ES300 Steering wheel to 2001.


Yes you can switch steering wheels, the wood grain is pricy. disconect the battery, wait 5min. remove caps from side of steering wheel. remove torx bolts from air bag assy. Remove wires from air bag. Place air bag upsode down in passenger seat. Make sure steering wheel is straight, remove 19mm nut and remove steering wheel.

Mar 06, 2009 | 1997 Lexus ES 300

Not finding what you are looking for?
2004 Jaguar X-Type Logo

1,125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

64034 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...