Question about 2002 Land Rover Freelander

1 Answer

Freelander heater switch 1997

When i turn on heater swich settings 1/2 does not work 3/4 work ok any suggestions thanks

Posted by on

  • 1 more comment 
  • graythomas Nov 15, 2008

    hi thanks would u no where resistor pack is. gray

  • graythomas Nov 23, 2008

    thankyou i will check it out

  • graythomas Nov 23, 2008

    thankyou i will check it out

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

The fan works at different speeds by switching to a different resister for the given speed. A common fault is the resister pack has a thermal overload/cutout which over time corrosion sets in and it breaks down. When you find the pack [normally under bonnet and in the motor cowling ]although not necessarily, you will see agroup of wires 4/5 remove the pack locate the thermal cutout ,bridge it and test ,if the fan works on all speeds #replace the unit# , we don't want a fire do we??. the information that i have supplied is for general electrical principles , and unless your freelander has computor controlled heating the principles will be the same. if it is computor controlled it could get expensive .Good luck i hope that i have helped in some way. Pat.

Posted on Nov 15, 2008

  • hoskingmach Nov 22, 2008

    hi gray, don't use this much, as you may have gathered. The resister pack is by the clutch pedal at the bottom of the heater box according to my sources.Common fault apparently,also i have always found that the local landy dealer/specialist to be a good bunch and are normally very helpful, cos we all love our landy's, we're strange that way. Good luck pat

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan primera 2002


REMOVE INTERIOR FAN FUSE AND GET ELECTRICIAN TO CHECK ,MAY BE HEATER CONTROL UNIT OR HEATER VALVE PROBLEM

Jan 12, 2014 | Cars & Trucks

1 Answer

Hi, The heater fan only works on setting 4. I have just replaced the Heater motor resister, but the problem is still there. I've checked the fuses all seem fine. Thanks in advance for your help.


can you tell me the type of swich you have knob type or electric type knob type the switch needs to be replaced. electric type the control board has burnt out.

Oct 02, 2013 | Opel Vectra Cars & Trucks

1 Answer

What causes the break light swich to push, ive took apart the swich and can push it and break lights worked but when i put swich back on with clip it dose not work when i hit the break peddel


nothing, It doesn't work like that, when your brake switch is mounted , correctly , your pedal has a bracket on it that pushes the switch plunger in so brake lights are off. when you push brake pedal in, to stop vehicle, the switch plunger (spring loaded) comes out to turn brake lights ON ! get it ? when you release pedal it pushes plunger in, to turn lights OFF !

Jan 15, 2013 | 1997 GMC Sierra

1 Answer

Fan blows but i get no heat


1. the hot/cold switch on the dash has become disconnected. (if the swich has suddenly become easier to operate this is the problem) reattach.

2. the heater tap/hoses are blocked/broken/unattached... (do the heater lines under the bonnet get hot? (two rubber hoses about 1/2 to 3/4 inch thick that run fron the engine to the firewall/cab.
repair/replace.

Sep 30, 2012 | 2006 Kia Sorento

1 Answer

Brake lights not working on a freelander td4 2004 bulbs ok fuse ok. 1 light went out first then they all gone off


brake pedal switch has ratchetted to far replace with new switch available from dealers.

Aug 23, 2010 | 2004 Land Rover FreeLander

1 Answer

2002 freelander blinkers won't work


Check/replace relay 6,located in fuse box lower dash under steering wheel.

May 04, 2010 | 2002 Land Rover Freelander

2 Answers

Heater would only work on high for last two years. One day it quit working, but we found that a fuse had blown. Now, a few weeks later, it quit again. This time it is not a fuse. The car is a 2000 Ford...


sounds like a bad swich. but since it all of a sudden quit on you the blower motor could be bad as well. you can connect power and ground to blower to see if it works. if it turns then the swich is bad.

Feb 23, 2010 | 2004 Chrysler Pacifica

1 Answer

Heating not working in landrover freelander 2001


I am having same problem with my freelander...blowing cold air. But I tried something like starting the veh and drive round for 10 mins then turn the heater speed control to 3 or 4....it started warming up and was OK until next day and I'm back with same routine...try it and see

Jan 08, 2010 | 2002 Land Rover Freelander

Not finding what you are looking for?
2002 Land Rover Freelander Logo

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

79123 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...