Question about 1999 Ford Super Duty F 550

2 Answers

1995 ford powerstroke

Engine won't fire not even with either. the hasn't been taken apart and it ran good when i parked it.what could be the problem?

Posted by on

  • yadayada
    yadayada May 11, 2010

    How is the fuel pressure, have the system tested for codes, until then we are shooting in the dark.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Check oil level, these run on oil pressure. Also check HPOP oil level, should be one inch from the top.

Posted on Sep 15, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 62 Answers

Try wd 40 to start it ,sounds like the piston rings are dry

Posted on Jul 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Truck just died at stop sign a block from home and will not start


assuming the vehicle is a diesel because you say you drained the water separator ? What engine ? What fuel pressure does it have to the injectors ? Do the injectors fire ?
Ford 7 3 powerstroke crank no start due to low icp injection pressure...
Do you know how to trouble shoot diesel engines ? Your best bet take it to a qualified repair shop .

May 06, 2017 | 2008 Ford F-350 Super Duty

1 Answer

1995 7.3 idi wont fire fuel or eather


have you taken off the valve covers to see if the connectors are broken the wires to the injectors and the glow plugs and they are molded into the valve cover gasket over time the little tab that holds them together breaks and they come apart the gaskets are about 110 dollars through dorman

Feb 12, 2014 | 1995 Ford F350

1 Answer

I PUT A NEW HIGH PRESSURE OIL PUMP IN MY 6.0 2003 POWERSTROKE IT RAN GOOD FOR TWO WEEKS THEN STARTED RUNNING ROUGH AND THEN DIED


Ford had a lot of problems with this engine. Most diagnosis requires a factory software scanner or one that can interface with the FICM module (fuel injector control module) Now you can perform injector buzz test and glow plug tests. If you can get running then also do a power balance test these test check fuel injectors statically and dynamically with the common rail oil pressure control sensor. These FICM modules are famous failure parts. Napa auto can get them.

Nov 07, 2013 | Ford F-350 Cars & Trucks

1 Answer

91 Buick Skylark ran when parked but now won't


Is the check engine light on when the engine is running ?
Someone will need to check for spark on all cylinders and fuel pressure.
You might try spraying carb cleaner or starting fluid into the throttle body to boost fuel supply and see if it helps. If it does that would tell you its a fuel problem.

Feb 06, 2013 | Cars & Trucks

1 Answer

1995 ford 7.3 powerstroke automatic shifts rough after transmission installed after replacing rear main seal


-check your transmission fluid level. park the truck on a level surface with the engine running and pull your dipstick and read the level in regards to the engine and trans temp (hot or cold)
-if that checks out i would go under the truck and check all of the electrical connectors that go to the transmission making sure they are secure and making good contact. also check the wiring to the tcm(normally located on the right side frame rail if i remember correctly)and make sure they are all secure and in good condition

Did you do the rear main seal yourself or did you pay a garage to do it? and is there anything else that was done at that time?

Jan 22, 2013 | 1995 Ford F350

2 Answers

I have a 1995 Ford F250 Powerstroke Hard Auto shifting


I had the same problem on my 95. The problem was the torque converter was not unlocking. It had to be replaced.

Mar 23, 2010 | 1995 Ford F250

1 Answer

1995 JEEP GRAND CHEROKEE RAN AND DIED WILL NOT START


They are easy to replace. Here is the location It is near the top of the transmission bell housing just to the left of centerline. You will need to unbolt it from underneath using a 7/16" socket on a long extension. Before doing so, set the parking brake and disconnect the transmission shifter linkage. Do this from underneath the truck. Let me know if this helps you at all

Jun 01, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Put new glow plugs in ran fine for 1 day now it wont start..


You may want to surf around on some of the powerstroke forums for detailed answers, but I know the powerstrokes use oil pressure to control the injectors so you may have some problems with the high pressure oil pump.
Again, it is just a guess. I just wanted to point you to some of the Ford Powerstroke forums which may be of much more help for you.
Good luck..

Feb 02, 2009 | 1997 Ford F350 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5623 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...